View SAB80515_1047015.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Microcomputer Components
SAB 80515/SAB 80C515 8-Bit Single-Chip Microcontroller Family
User's Manual 08.95
SAB 80515 / SAB 80C515 Family Revision History: 8.95 Previous Releases: Page 30 39 80 105 106 109 137 152 243 301 12.90/10.92
Subjects (changes since last revision) Modified timing diagram (PSEN rising edge) More detailed description of ACMOS port structure Differential output impedance of analog reference supply voltage now: 1 k Second paragraph: additional description; WDT reset information added SWDT reset information added Figure 7-51 corrected Encoding of ADD A, direct corrected Encoding of CPL bit corrected New release of SAB 80C515 / SAB 80C535 data sheet inserted New release of SAB 80515 / SAB 80535 data sheet inserted
Edition 08.95 Published by Siemens AG, Bereich Halbleiter, MarketingKommunikation, Balanstrae 73, 81541 Munchen (c) Siemens AG 1995. All Rights Reserved. Attention please! As far as patents or other rights of third parties are concerned, liability is only assumed for components, not for applications, processes and circuits implemented within components or assemblies. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. For questions on technology, delivery and prices please contact the Semiconductor Group Offices in Germany or the Siemens Companies and Representatives worldwide (see address list). Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Siemens Office, Semiconductor Group. Siemens AG is an approved CECC manufacturer. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components1 of the Semiconductor Group of Siemens AG, may only be used in life-support devices or systems2 with the express written approval of the Semiconductor Group of Siemens AG. 1 A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered.
Contents
Contents 1 2 2.1 2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 2.1.6 2.1.7 3 3.1 3.2 4 4.1 4.2 4.3 4.4 5 5.1 5.2 5.3 5.4 6 6.1 6.1.1 6.1.2 7 7.1 7.1.1 7.1.1.1 7.1.1.2 7.1.1.3 7.1.2 7.1.3 7.1.4 7.1.4.1
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Fundamental Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Differences between MYMOS (SAB 80515/80535) and ACMOS (SAB 80C515/80C535) Versions . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Power Saving Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Special Function Register PCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Port Driver Circuitries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 The A/D Converter Input Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 A/D Converter Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 The Oscillator and Clock Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 The VBB Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Central Processing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 CPU Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Memory Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 General Purpose Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Special Function Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 External Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Accessing External Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 PSEN, Program Store Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 ALE, Address Latch Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Overlapping External Data and Program Memory Spaces . . . . . . . . . . . . . .29 System Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Hardware Reset and Power-Up Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Reset Function and Circuitries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Hardware Reset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 On-Chip Peripheral Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Parallel I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Port Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Digital I/O Port Circuitry (MYMOS/ACMOS) . . . . . . . . . . . . . . . . . . . . . . . . .36 MYMOS Port Driver Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 ACMOS Port Driver Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Port 0 and Port 2 Used as Address/Data Bus . . . . . . . . . . . . . . . . . . . . . . . .41 Alternate Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Port Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
3
Semiconductor Group
Contents
Contents 7.1.4.2 7.1.4.3 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.4.1 7.2.4.2 7.2.4.3 7.2.4.4 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.4 7.4.1 7.4.1.1 7.4.1.2 7.4.2 7.4.3 7.5 7.5.1 7.5.2 7.5.2.1 7.5.2.2 7.5.2.3 7.5.3 7.6 7.6.1 7.6.1.1 7.6.2 7.6.2.1 7.6.2.2 7.7
Page
Port Loading and Interfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Read-Modify-Write Feature of Ports 0 through 5 . . . . . . . . . . . . . . . . . . . . . .45 Serial Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Operating Modes of Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Multiprocessor Communication Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Baud Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Detailed Description of the Operating Modes . . . . . . . . . . . . . . . . . . . . . . . .54 Mode 0, Synchronous Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Mode 1, 8-Bit UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Mode 2, 9-Bit UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Mode 3, 9-Bit UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Timer 0 and Timer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 A/D Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Function and Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 lnitialization and Input Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Start of Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Reference Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 A/D Converter Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 Timer 2 with Additional Compare/Capture/Reload . . . . . . . . . . . . . . . . . . . . .82 Timer 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Compare Function of Registers CRC, CC1 to CC3 . . . . . . . . . . . . . . . . . . . .88 Compare Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 Compare Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Using Interrupts in Combination with the Compare Function . . . . . . . . . . . . .94 Capture Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Power Saving Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 Power Saving Modes of the SAB 80515/80535 . . . . . . . . . . . . . . . . . . . . . . .99 Power-Down Mode of the SAB 80515/80535 . . . . . . . . . . . . . . . . . . . . . . . .99 Power Saving Modes of the SAB 80515/80535 . . . . . . . . . . . . . . . . . . . . . .100 Power-Down Mode of the SAB 80C515/80C535 . . . . . . . . . . . . . . . . . . . . .101 Idle Mode of the SAB 80C515/80C535 . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Semiconductor Group
4
Contents
Contents 7.8 7.8.1 7.8.2 7.8.2.1 7.8.2.2 7.9 8 8.1 8.2 8.3 8.4 8.5 9 9.1 9.2 9.2.1 9.2.2 9.2.3 9.2.4 9.3 10
Page
Oscillator and Clock Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Crystal Oscillator Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Driving for External Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Driving the SAB 80515/80535 from External Source . . . . . . . . . . . . . . . . . .108 Driving the SAB 80C515/80C535 from External Source . . . . . . . . . . . . . . .109 System Clock Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Interrupt System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Interrupt Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Priority Level Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 How Interrupts are Handled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 External Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Response Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Introduction to the Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Arithmetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 Control Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 Instruction Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 Device Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214
Semiconductor Group
5
Introduction
1
Introduction
The SAB 80C515/80C535 is a new, powerful member of the Siemens SAB 8051 family of 8-bit microcontrollers. lt is designed in Siemens ACMOS technology and is functionally compatible with the SAB 80515/80535 devices designed in MYMOS technology. The ACMOS and the MYMOS versions 1) 2) are stand-alone, high-performance single-chip microcontrollers based on the SAB 8051/80C51 architecture. While maintaining all the SAB 80(C)51 operating characteristics, the SAB 80(C)515/80(C)535 3) incorporate several enhancements which significantly increase design flexibility and overall system performance. The low-power properties of Siemens ACMOS technology allow applications where power consumption and dissipation are critical. Furthermore, the SAB 80C515/80C535 has two softwareselectable modes of reduced activity for further power reduction: idle and power-down mode. The SAB 80(C)535 is identical to the SAB 80(C)515 except that it lacks the on-chip program memory. The SAB 80(C)515/80(C)535 is supplied in a 68-pin plastic leaded chip carrier package (P-LCC-68). In addition to the standard temperature range version (0 to + 70 C) there are also versions for extended temperature ranges available (see data sheets). Functional Description The members of the SAB 80515 family of microcontrollers are: - SAB 80C515: Microcontroller, designed in Siemens ACMOS technology, with 8-Kbyte factory mask-programmable ROM - SAB 80C535: ROM-less version, identical to the SAB 80C515 - SAB 80515: Microcontroller, designed in Siemens MYMOS technology, with 8-Kbyte factory mask-programmable ROM - SAB 80535: ROM-less version, identical to the SAB 80515 - SAB 80515K: Special ROM-less version of the SAB 80515 with an additional interface for program memory accesses. An external ROM that is accessed via the interface substitutes the SAB 80515's internal ROM.
1 2 3
In this User's Manual the term "ACMOS versions" is used to refer to both the SAB 80C515 and SAB 80C535. The term "MYMOS versions" stands for SAB 80535 and SAB 80515. The term "SAB 80(C)515" refers to the SAB 80515 and the SAB 80C515, unless otherwise noted. 6
Semiconductor Group
Introduction
The SAB 80(C)515 features are: - - - - - - - - - - - - - - - - - - - 8 Kbyte on-chip program memory 256 byte on-chip RAM Six 8-bit parallel I/O ports One input port for digital input 1) Full-duplex serial port, 4 modes of operation, fixed or variabie baud rates Three 16-bit timer/counters 16-bit reload, compare, capture capability A/D converter, 8 multiplexed analog inputs, programmable reference voltages 16-bit watchdog timer Power-down supply for 40 byte of RAM Boolean processor 256 directly addressable bits 12 interrupt sources (7 external, 5 internal), 4 priority levels Stack depth up to 256 byte 1 s instruction cycle at 12-MHz operation 4 s multiply and divide External program and data memory expandable up to 64 Kbyte each Compatible with standard SAB 8080/8085 peripherals and memories Space-saving P-LCC-68 package
For small-quantity applications and system development the SAB 80535 can be employed being the equivalent of an SAB 80515 without on-chip ROM.
1
Additional feature of the ACMOS versions
Semiconductor Group
7
Introduction
Figure 1-1 shows the logic symbol, figure 1-2 the block diagram of the SAB 80(C)515:
Figure 1-1 Logic Symbol
Semiconductor Group
8
Introduction
Figure 1-2 Block Diagram Semiconductor Group 9
Fundamental Structure
2
Fundamental Structure
The SAB 80(C)515/80(C)535 is a totally 8051-compatible microcontroller while its peripheral performance has been increased significantly. Some of the various peripherals have been added to support the 8-bit core in case of stringent embedded control requirements without loosing compatibility to the 8051 architecture. Furthermore, the SAB 80(C)515/80(C)535 contains e. g. an additional 8-bit A/D converter, two times as much ROM and RAM as the 80(C)51 and an additional timer with compare/capture/reload facilities for all kinds of digital signal processing. Figure 2.1 shows a block diagram of the SAB 80(C)515/80(C)535. The SAB 80C515/80C535 combines the powerful architecture of the industry standard controller SAB 80515/80535 with the advantages of the ACMOS technology (e. g. power-saving modes). The differences between MYMOS and ACMOS components are explained in section 2.1. Readers who are familiar with the SAB 8051 may concentrate on chapters 2.1, 6, 7 and 8 where the differences between MYMOS and ACMOS components, the reset conditions, the peripherals and the interrupt system are described. For newcomers to the 8051 family of microcontrollers, the following section gives a general view of the basic characteristics of the SAB 80515/80535. The details of operation are described later in chapters 3 and 4.
Semiconductor Group
10
Fundamental Structure
Central Processing Unit The CPU is designed to operate on bits and bytes. The instructions, which consist of up to 3 bytes, are performed in one, two or four machine cycles. One machine cycle requires twelve oscillator cycles. The instruction set has extensive facilities for data transfer, logic and arithmetic instructions. The Boolean processor has its own full-featured and bit-based instructions within the instruction set. The SAB 80(C)515/80(C)535 uses five addressing modes: direct access, immediate, register, register indirect access, and for accessing the external data or program memory portions a base register plus index-register indirect addressing. Memory Organization The SAB 80C515, 80515 have an internal ROM of 8 Kbyte. The program memory can externally be expanded up to 64 Kbyte (see bus expansion control). The internal RAM consists of 256 bytes. Within this address space there are 128 bit-addressable locations and four register banks, each with 8 general purpose registers. In addition to the internal RAM there is a further 128-byte address space for the special function registers, which are described in sections to follow. Because of its Harvard architecture, the SAB 80(C)515/80(C)535 distinguishes between an external program memory portion (as mentioned above) and up to 64 Kbyte external data memory accessed by a set of special instructions. Bus Expansion Control The external bus interface of the SAB 80(C)515/80(C)535 consists of an 8-bit data bus (port 0), a 16-bit address bus (port 0 and port 2) and five control lines. The address latch enable signal (ALE) is used to demultiplex address and data of port 0. The program memory is accessed by the program store enable signal (PSEN) twice a machine cycle. A separate external access line (EA) is used to inform the controller while executing out of the lower 8 Kbyte of the program memory, whether to operate out of the internal or external program memory. The read or write strobe (RD, WR) is used for accessing the external data memory. Peripheral Control All on-chip peripheral components - I/O ports, serial interface, timers, compare/capture registers, the interrupt controller and the A/D converter - are handled and controlled by the so-called special function registers. These registers constitute the easy-to-handle interface with the peripherals. This peripheral control concept, as implemented in the SAB 8051, provides the high flexibility for further expansion as done in the SAB 80(C)515/80(C)535. Moreover some of the special function registers, like accumulator, B-register, program status word (PSW), stack pointer (SP) and the data pointer (DPTR) are used by the CPU and maintain the machine status.
Semiconductor Group
11
Fundamental Structure
Figure 2-1 Detailed Block Diagram Semiconductor Group 12
Fundamental Structure
2.1
Differences between MYMOS (SAB 80515/80535) and ACMOS (SAB 80C515/80C535) Versions
There are some differences between MYMOS and ACMOS versions concerning: - - - - - - - 2.1.1 Power Saving Modes Special Function Register PCON Port Driver Circuitry A/D Converter Input Ports A/D Converter Conversion Time Oscillator and Clock Circuit VBB Pin Power Saving Modes
The SAB 80515/80535 has just the power-down mode, which allows retention of the on-chip RAM contents through a backup supply connected to the VPD pin. The SAB 80C515/80C535 additionally has the following features: idle mode the same power supply pin VCC for active, power-down and idle mode an extra pin (PE) that allows enabling/disabling the power saving modes starting of the power-saving modes by software via special function register PCON (Power Control Register) - protection against unintentional starting of the power-saving modes These items are described in detail in section 7.6. 2.1.2 Special Function Register PCON - - - -
In the MYMOS version SAB 80515/80535 the SFR PCON (address 87H ) contains only bit 7 (SMOD). In the ACMOS version SAB 80C515/80C535 there are additional bits used (see figure 2-2). The bits PDE, PDS and IDLE, IDLS select the power-down mode or idle mode, respectively, when the power saving modes are enabled by pin PE. Furthermore, register PCON of the ACMOS version contains two general-purpose flags. For example, the flag bits GF0 and GF1 can be used to indicate whether an interrupt has occurred during normal operation or during idle. Then an instruction that activates idle can also set one or both flag bits. When idle is terminated by an interrupt, the interrupt service routine can sample the flag bits.
Semiconductor Group
13
Fundamental Structure
2.1.3
Port Driver Circuitries
The port structures of the MYMOS and ACMOS versions are functionally compatible. For low power consumption the pullup arrangement is realized differently in both versions. Chapters 7.1.1.1, 7.1.1.2, 7.1.1.3 are dealing with the port structures in detail. 2.1.4 The A/D Converter Input Ports
The analog input ports (AN0 to AN7) of the SAB 80515/80535 can only be used as analog inputs for the A/D converter. The analog input ports (P6.0 to P6.7) of the SAB 80C515/80C535 can be used either as input channels for the A/D converter or as digital inputs (see chapter 7.4) Figure 2-2 Special Function Register PCON (Address 87H) 87H SMOD 7 PDS 6 IDLS 5 - 4 GF1 3 GF0 2 PDE 1 IDLE 0 PCON
These bits are available in the MYMOS version
Symbol SMOD PDS
Position PCON.7 PCON.6
Function When set, the baud rate of the serial channel in mode 1, 2, 3 is doubled. Power-down start bit. The instruction that sets the PDS flag bit is the last instruction before entering the power-down mode. Idle start bit. The instruction that sets the IDLS flag bit is the last instruction before entering the idle mode. Reserved General purpose flag General purpose flag Power-down enable bit. When set, starting of the power-down mode is enabled. Idle mode enable bit. When set, starting of the idle mode is enabled.
IDLS
PCON.5
- GF1 GF0 PDE
PCON.4 PCON.3 PCON.2 PCON.1
IDLE
PCON.0
Semiconductor Group
14
Fundamental Structure
2.1.5
A/D Converter Timings
See the corresponding data sheets for the specification of tL (load time), tS (sample time), tC (conversion time). 2.1.6 The Oscillator and Clock Circuits
There is no difference between the MYMOS and ACMOS versions if they are driven from a crystal or a ceramic resonator. Please note that there is a difference between driving MYMOS and ACMOS components from external source. How to drive each device is described in chapter 7.8.2 and in each data sheet. 2.1.7 The VBB Pin
The SAB 80515/80535 has an extra VBB pin connected to the device's substrate. lt must be connected to VSS through a capacitor for proper operation of the A/D converter. The SAB 80C515/80C535 has no VBB pin. In ACMOS technology the substrate is directly connected to VCC ; therefore, the corresponding pin is used as an additional VCC pin.
Semiconductor Group
15
Central Processing Unit
3 3.1
Central Processing Unit General Description
The CPU (Central Processing Unit) of the SAB 80(C)515 consists of the instruction decoder, the arithmetic section and the program control section. Each program instruction is decoded by the instruction decoder. This unit generates the internal signals controlling the functions of the individual units within the CPU. They have an effect on the source and destination of data transfers, and control the ALU processing. The arithmetic section of the processor performs extensive data manipulation and is comprised of the Arithmetic/Logic Unit (ALU), an A register, B register and PSW register. The ALU accepts 8-bit data words from one or two sources and generates an 8-bit result under the control of the instruction decoder. The ALU performs the arithmetic operations add, subtract, multiply, divide, increment, decrement, BCD-decimal-add-adjust and compare, and the logic operations AND, OR, Exclusive OR, complement and rotate (right, left or swap nibble (left four)). Also included is a Boolean processor performing the bit operations of set, clear, complement, jump-if-not-set, jump-if-set-andclear and move to/from carry. Between any addressable bit (or its complement) and the carry flag, it can perform the bit operations of logical AND or logical OR with the result returned to the carry flag. The A, B and PSW registers are described in section 4.4. The program control section controls the sequence in which the instructions stored in program memory are executed. The 16-bit program counter (PC) holds the address of the next instruction to be executed. The PC is manipulated by the control transfer instructions listed in the chapter "Instruction Set". The conditional branch logic enables internal and external events to the processor to cause a change in the program execution sequence.
Semiconductor Group
16
Central Processing Unit
3.2
CPU Timing
A machine cycle consists of 6 states (12 oscillator periods). Each state is divided into a phase 1 half, during which the phase 1 clock is active, and a phase 2 half, during which the phase 2 clock is active. Thus, a machine cycle consists of 12 oscillator periods, numbered S1P1 (state 1, phase 1) through S6P2 (state 6, phase 2). Each state lasts for two oscillator periods. Typically, arithmetic and logical operations take place during phase 1 and internal register-to-register transfers take place during phase 2. The diagrams in figure 3-1 show the fetch/execute timing related to the internal states and phases. Since these internal clock signals are not user-accessible, the XTAL2 oscillator signals and the ALE (address latch enable) signal are shown for external reference. ALE is normally activated twice during each machine cycle: once during S1P2 and S2P1, and again during S4P2 and S5P1. Execution of a one-cycle instruction begins at S1P2, when the op-code is latched into the instruction register. lf it is a two-byte instruction, the second is read during S4 of the same machine cycle. lf it is a one-byte instruction, there is still a fetch at S4, but the byte read (which would be the next opcode) is ignored, and the program counter is not incremented. In any case, execution is completed at the end of S6P2. Figures 3-1 A) and B) show the timing of a 1-byte, 1-cycle instruction and for a 2-byte, 1-cycle instruction. Most SAB 80(C)515 instructions are executed in one cycle. MUL (multiply) and DIV (divide) are the only instructions that take more than two cycles to complete; they take four cycles. Normally two code bytes are fetched from the program memory during every machine cycle. The only exception to this is when a MOVX instruction is executed. MOVX is a one-byte, 2-cycle instruction that accesses external data memory. During a MOVX, the two fetches in the second cycle are skipped while the external data memory is being addressed and strobed. Figures 3-1 C) and D) show the timing for a normal 1-byte, 2-cycle instruction and for a MOVX instruction.
Semiconductor Group
17
Central Processing Unit
Figure 3-1 Fetch/Execute Sequence
Semiconductor Group
18
Memory Organization
4
Memory Organization
The SAB 80(C)515 CPU manipulates operands in the following four address spaces: - - - - 4.1 up to 64 Kbyte of program memory up to 64 Kbyte of external data memory 256 bytes of internal data memory a 128-byte special function register area Program Memory
The program memory of the SAB 80(C)515 consists of an internal and an external memory portion (see figure 4-1). 8 Kbyte of program memory may reside on-chip (SAB 80C515/80515 only), while the SAB 80C535/80535 has no internal ROM. The program memory can be externally expanded up to 64 Kbyte. If the EA pin is held high, the SAB 80(C)515 executes out of the internal program memory unless the address exceeds 1FFF H. Locations 2000H through 0FFFFH are then fetched from the external memory. If the EA pin is held low, the SAB 80(C)515 fetches all instructions from the external program memory. Since the SAB 80C535/80535 has no internal program memory, pin EA must be tied low when using this device. In either case, the 16-bit program counter is the addressing mechanism. Locations 03H through 93H in the program memory are used by interrupt service routines. 4.2 Data Memory
The data memory address space consists of an internal and an external memory portion. Internal Data Memory The internal data memory address space is divided into three physically separate and distinct blocks: the lower 128 bytes of RAM, the upper 128-byte RAM area, and the 128-byte special function register (SFR) area (see figure 4-2). Since the latter SFR area and the upper RAM area share the same address locations, they must be accessed through different addressing modes. The map in figure 4-2 and the following table show the addressing modes used for the different RAM/ SFR spaces.
Semiconductor Group
19
Memory Organization
Address Space Lower 128 bytes of RAM Upper 128 bytes of RAM Special function registers
Locations 00H to 7FH 80H to 0FFH 80H to 0FFH
Addressing Mode direct/indirect indirect direct
For details about the addressing modes see chapter 9.1.
Figure 4-1 Program Memory Address Space The lower 128 bytes of the internal RAM are again grouped in three address spaces (see figure 4-3): 1) 2) A general purpose register area occupies locations 0 through 1FH (see also section 4.3). The next 16 bytes, location 20H through 2FH, contain 128 directly addressable bits. Programming information: These bits can be referred to in two ways, both of which are acceptable for the ASM51. One way is to refer to their bit addresses, i.e. 0 to 7FH. The other way is by referencing to bytes 20H to 2FH. Thus bits 0 to 7 can also be referred to as bits 20.0 to 20.7, and bits 08H and 0FH are the same as 21.0 to 21.7 and so on. Each of the 16 bytes in this segment may also be addressed as a byte.) Locations 30H to 7FH can be used as a scratch pad area. 20
3)
Semiconductor Group
Memory Organization
Using the Stack Pointer (SP) - a special function register described in section 4.4 - the stack can be located anywhere in the whole internal data memory address space. The stack depth is limited only by the internal RAM available (256 byte maximum). However, the user has to take care that the stack is not overwritten by other data, and vice versa. External Data Memory Figure 4-2 and 4-3 contain memory maps which illustrate the internal/external data memory. To address data memory external to the chip, the "MOVX" instructions in combination with the 16-bit datapointer or an 8-bit general purpose register are used. Refer to chapter 9 (Instruction Set) or 5 (External Bus Interface) for detailed descriptions of these operations. A maximum of 64 Kbytes of external data memory can be accessed by instructions using 16-bit address.
Figure 4-2 Data Memory / SFR Address Space Semiconductor Group 21
Memory Organization
Figure 4-3 Mapping of the Lower Portion of the Internal Data Memory Semiconductor Group 22
Memory Organization
4.3
General Purpose Register
The lower 32 locations of the internal RAM are assigned to four banks with eight general purpose register (GPRs) each. Only one of these banks may be enabled at a time. Two bits in the program status word, PSW.3 and PSW.4, select the active register bank (see description of the PSW). This allows fast context switching, which is useful when entering subroutines or interrupt service routines. ASM51 and the device SAB 80(C)515 default to register bank 0. The 8 general purpose registers of the selected register bank may be accessed by register addressing. With register addressing the instruction op code indicates which register is to be used. For indirect accessing R0 and R1 are used as pointer or index register to address internal or external memory (e.g. MOV @R0). Reset initializes the stack pointer to location 07H and increments it once to start from location 08H which is also the first register (R0) of register bank 1. Thus, if one is going to use more than one register bank, the SP should be initiated to a different location of the RAM which is not used for data storage. 4.4 Special Function Registers
The Special Function Register (SFR) area has two important functions. Firstly, all CPU register except the program counter and the four register banks reside here. The CPU registers are the arithmetic registers like A, B, PSW and pointers like SP, DPH and DPL. Secondly, a number of registers constitute the interface between the CPU and all on-chip peripherals. That means, all control and data transfers from and to the peripherals use this register interface exclusively. The special function register area is located in the address space above the internal RAM from addresses 80H to FFH. All 41 special function registers of the SAB 80(C)515 reside here. Fifteen SFRs, that are located on addresses dividable by eight, are bit-addressable, thus allowing 128 bit-addressable locations within the SFR area. Since the SFR area is memory mapped, access to the special function registers is as easy as with internal RAM, and they may be processed with most instructions. In addition, if the special functions are not used, some of them may be used as general scratch pad registers. Note, however, all SFRs can be accessed by direct addressing only. The special function registers are listed in table 4-1. Bit- and byte-addressable special function registers are marked with an asterisk at the symbol name.
Semiconductor Group
23
Memory Organization
Table 4-1 Special Function Registers Symbol * P0 SP DPL DPH PCON TCON TMOD TL0 TL1 TH0 TH1 P1 SCON SBUF P2 IEN0 IP0 P3 IEN1 IP1 IRCON CCEN CCL1 CCH1 CCL2 CCH2 CCL3 CCH3 T2CON CRCL CRCH TL2 TH2 PSW ADCON ADDAT DAPR P6 ACC P4 B P5 Name Port 0 Stack pointer Data pointer, low byte Data pointer, high byte Power control register Timer control register Timer mode register Timer 0, low byte Timer 1, low byte Timer 0, high byte Timer 1, high byte Port 1 Serial channel control register Serial channel buffer register Port 2 Interrupt enable register 0 Interrupt priority register 0 Port 3 Interrupt enable register 1 Interrupt priority register 1 Interrupt request control register Compare/capture enable register Compare/capture register 1, low byte Compare/capture register 1, high byte Compare/capture register 2, low byte Compare/capture register 2, high byte Compare/capture register 3, low byte Compare/capture register 3, high byte Timer 2 control register Compare/reload/capture register, low byte Compare/reload/capture register, high byte Timer 2, low byte Timer 2, high byte Program status word register A/D converter control register A/D converter data register D/A converter program register Port 6 Accumulator Port 4 B register Port 5 Address 80H 81H 82H 83H 87H 88H 89H 8AH 8BH 8CH 8DH 90H 98H 99H 0A0H 0A8H 0A9H 0B0H 0B8H 0B9H 0C0H 0C1H 0C2H 0C3H 0C4H 0C5H 0C6H 0C7H 0C8H 0CAH 0CBH 0CCH 0CDH 0D0H 0D8H 0D9H 0DAH 0DBH 1) 0E0H 0E8H 0F0H 0F8H
*
* * * * * * *
*
* *
* * * *
The SFR's marked with an asterisk (*) are bit- and byte-addressable. 1) Additional feature of the ACMOS versions
Semiconductor Group
24
Memory Organization
The following paragraphs give a general overview of the special function register and refer to sections where a more detailed description can be found. Accumulator, SFR Address 0E0H ACC is the symbol for the accumulator register. The mnemonics for accumulator-specific instructions, however, refer to the accumulator simply as A. Figure 4-4 Program Status Word Register (PSW), SFR Address 0D0H 0D7H 0D0H CY 0D6H AC 0D5H F0 0D4H RS1 0D3H RS0 0D2H OV 0D1H F1 0D0H P PSW
The PSW register contains program status information. Bit CY AC F0 RS1 0 0 1 1 OV F1 P RS0 0 1 0 1 Function Carry flag Auxiliary carry flag (for BCD operations) General purpose user flag 0 Register bank select control bits Bank 0 selected, data address 00H - 07H Bank 1 selected, data address 08H - 0FH Bank 2 selected, data address 10H - 17H Bank 3 selected, data address 18H - 1F7 Overflow flag General purpose user flag Parity flag. Set/cleared by hardware each instruction cycle to indicate an odd/ even number of "one" bits in the accumulator, i.e. even parity.
B Register, SPF Address 0F0H The B register is used during multiply and divide and serves as both source and destination. For other instructions it can be treated as another scratch pad register. Stack Pointer, SFR Address 081H The Stack Pointer (SP) register is 8 bits wide. It is incriminated before data is stored during PUSH and CALL executions and decremented after data is popped during a POP and RET (RETI) execution, i.e. it always points to the last valid stack byte. While the stack may reside anywhere in on-chip RAM, the stack pointer is initialized to 07H after a reset. This causes the stack to begin at location 08H above register bank zero. The SP can be read or written under software control.
Semiconductor Group
25
Memory Organization
Datapointer, SFR Address 082H and 083H The 16-bit Datapointer (DPTR) register is a concatenation of registers DPH (data pointer's high order byte) and DPL (data pointer's low order byte). The data pointer is used in register-indirect addressing to move program memory constants and external data memory variables, as well as to branch within the 64 Kbyte program memory address space. Ports 0 to 5 P0 to P5 are the SFR latches to port 0 to 5, respectively. The port SFRs 0 to 5 are bit-addressable. Ports 0 to 5 are 8-bit I/O ports (that is in total 48 I/O lines) which may be used as general purpose ports and which provide alternate output functions dedicated to the on-chip peripherals of the SAB 80(C)515. Port 6 (AN0 to AN7) In the MYMOS versions, the analog input lines AN0 to AN7 can only be used as inputs for the A/D converter. In the ACMCS versions these lines may also be used as digital inputs. In this case they are addressed as an additional input port (port 6) via special function register P6 (0DBH). Since port 6 has no internal latch, the contents of SFR P6 only depends on the levels applied to the input lines. For details about this port please refer to section 7.1 (Parallel I/O). Peripheral Control, Data and Status Registers Most of the special function registers are used as control, status, and data registers to handle the on-chip peripherals. In the special function register table the register names are organized in groups and each of these groups refer to one peripheral unit. More details on how to program these registers are given in the descriptions of the following peripheral units: Unit Ports Serial Channel Timer 0/1 A/D-Converter Timer 2 with Comp/Capt/Reload Power Saving Modes Watchdog Timer Interrupt System Symbol - - - ADC CCU - WDT - Section 7.1 7.2 7.3 7.4 7.5 7.6 7.7 8
Semiconductor Group
26
External Bus Interface
5
External Bus Interface
The SAB 80(C)515 allows for external memory expansion. To accomplish this, the external bus interface common to most 8051-based controllers is employed. 5.1 Accessing External Memory
lt is possible to distinguish between accesses to external program memory and external data memory or other peripheral components respectively. This distinction is made by hardware: accesses to external program memory use the signal PSEN (program store enable) as a read strobe. Accesses to external data memory use RD and WR to strobe the memory (alternate functions of P3.7 and P3.6, see section 7.1.). Port 0 and port 2 (with exceptions) are used to provide data and address signals. In this section only the port 0 and port 2 functions relevant to external memory accesses are described (for further details see chapter 7.1). Fetches from external program memory always use a 16-bit address. Accesses to external data memory can use either a 16-bit address (MOVX @DPTR) or an 8-bit address (MOVX @Ri). Role of P0 and P2 as Data/Address Bus When used for accessing external memory, port 0 provides the data byte time-multiplexed with the low byte of the address. In this state, port 0 is disconnected from its own port latch, and the address/ data signal drives both FETs in the port 0 output buffers. Thus, in this application, the port 0 pins are not open-drain outputs and do not require external pullup resistors. During any access to external memory, the CPU writes 0FFH to the port 0 latch (the special function register), thus obliterating whatever information the port 0 SFR may have been holding. Whenever a 16-bit address is used, the high byte of the address comes out on port 2, where it is held for the duration of the read or write cycle. During this time, the port 2 lines are disconnected from the port 2 latch (the special function register). Thus the port 2 latch does not have to contain 1 s, and the contents of the port 2 SFR are not modified. lf an 8-bit address is used (MOVX @Ri), the contents of the port 2 SFR remain at the port 2 pins throughout the external memory cycle. This will facilitate paging. lt should be noted that, if a port 2 pin outputs an address bit that is a 1, strong pullups will be used for the entire read/write cycle and not only for two oscillator periods.
Semiconductor Group
27
External Bus Interface
Timing The timing of the external bus interface, in particular the relationship between the control signals ALE, PSEN, RD and information on port 0 and port 2, is illustrated in figure 5-1 a) and b). Data memory: in a write cycle, the data byte to be written appears on port 0 just before WR is activated, and remains there until after WR is deactivated. In a read cycle, the incoming byte is accepted at port 0 before the read strobe is deactivated.
Program memory: signal PSEN functions as a read strobe. For further information see section 5.2. External Program Memory Access The external program memory is accessed under two conditions: - whenever signal EA is active; or - whenever the program counter (PC) contains a number that is larger than 01FFF H. This requires the ROM-less versions SAB 80C535/80535 to have EA wired low to allow the lower 8 K program bytes to be fetched from external memory. When the CPU is executing out of external program memory, all 8 bits of port 2 are dedicated to an output function and may not be used for general-purpose I/O. The contents of the port 2 SFR however is not affected. During external program memory fetches port 2 lines output the high byte of the PC, and during accesses to external data memory they output either DPH or the port 2 SFR (depending on whether the external data memory access is a MOVX @DPTR or a MOVX @Ri). Since the SAB 80C535/80535 has no internal program memory, accesses to program memory are always external, and port 2 is at all times dedicated to output the high-order address byte. This means that port 0 and port 2 of the SAB 80C535/80535 can never be used as general-purpose I/O. This also applies to the SAB 80C515/80515 when it is operated with only an external program memory.
Semiconductor Group
28
External Bus Interface
5.2
PSEN, Program Store Enable
The read strobe for external fetches is PSEN. PSEN is not activated for internal fetches. When the CPU is accessing external program memory, PSEN is activated twice every cycle (except during a MOVX instruction) no matter whether or not the byte fetched is actually needed for the current instruction. When PSEN is activated its timing is not the same as for RD. A complete RD cycle, including activation and deactivation of ALE and RD, takes 12 oscillator periods. A complete PSEN cycle, including activation and deactivation of ALE and PSEN takes 6 oscillator periods. The execution sequence for these two types of read cycles is shown in figure 5-1 a) and b). 5.3 ALE, Address Latch Enable
The main function of ALE is to provide a properly timed signal to latch the low byte of an address from P0 into an external latch during fetches from external memory. The address byte is valid at the negative transition of ALE. For that purpose, ALE is activated twice every machine cycle. This activation takes place even it the cycle involves no external fetch. The only time no ALE pulse comes out is during an access to external data memory when RD/WR signals are active. The first ALE of the second cycle of a MOVX instruction is missing (see figure 5-1b) ). Consequently, in any system that does not use data memory, ALE is activated at a constant rate of 1/6 of the oscillator frequency and can be used for external clocking or timing purposes. 5.4 Overlapping External Data and Program Memory Spaces
In some applications it is desirable to execute a program from the same physical memory that is used for storing data. In the SAB 80(C)515, the external program and data memory spaces can be combined by AND-ing PSEN and RD. A positive logic AND of these two signals produces an active low read strobe that can be used for the combined physical memory. Since the PSEN cycle is faster than the RD cycle, the external memory needs to be fast enough to adapt to the PSEN cycle.
Semiconductor Group
29
External Bus Interface
Figure 5-1 a) and b) External Program Memory Execution Semiconductor Group 30
System Reset
6 6.1 6.1.1
System Reset Hardware Reset and Power-Up Reset Reset Function and Circuitries
The hardware reset function incorporated in the SAB 80(C)515 allows for an easy automatic startup at a minimum of additional hardware and forces the controller to a predefined default state. The hardware reset function can also be used during normal operation in order to restart the device. This is particularly done when the power-down mode (see section 7.6) is to be terminated. In addition to the hardware reset, which is applied externally to the SAB 80(C)515, there is also the possibility of an internal hardware reset. This internal reset will be initiated by the watchdog timer (section 7.7). The reset input is an active low input at pin 10 (RESET). An internal Schmitt trigger is used at the input for noise rejection. Since the reset is synchronized internally, the RESET pin must be held low for at least two machine cycles (24 oscillator periods) while the oscillator is running. With the oscillator running the internal reset is executed during the second machine cycle in which RESET is low and is repeated every cycle until RESET goes high again. During reset, pins ALE and PSEN are configured as inputs and should not be stimulated externally. (An external stimulation at these lines during reset activates several test modes which are reserved for test purposes. This in turn may cause unpredictable output operations at several port pins). A pullup resistor is internally connected to VCC to allow a power-up reset with an external capacitor only. An automatic reset can be obtained when VCC is applied by connecting the reset pin to VSS via a capacitor as shown in figure 6-1 a) and c). After VCC has been turned on the capacitor must hold the voltage level at the reset pin for a specified time below the upper threshold of the Schmitt trigger to effect a complete reset. The time required is the oscillator start-up time plus 2 machine cycles, which, under normal conditions, must be at least 10 - 20 ms for a crystal oscillator. This requirement is usually met using a capacitor of 4.7 to 10 microfarad. The same considerations apply if the reset signal is generated externally (figure 6-1 b) ). In each case it must be assured that the oscillator has started up properly and that at least two machine cycles have passed before the reset signal goes inactive.
Semiconductor Group
31
System Reset
Figure 6-1 a) - c) Reset Circuitries A correct reset leaves the processor in a defined state. The program execution starts at location 0000H. The default values of the special function registers (SFR) during and after reset are listed in table 6-1. After reset is internally accomplished the contents of the port latches of port 0 to 5 is 0FFH. This leaves port 0 floating, since it is an open drain port when not used as data/address bus. All other I/O port lines (ports 1 through 5) output a one (1). In the MYMOS versions, the analog input lines AN0 to AN7 can only be used as inputs. In the ACMOS versions these lines may also be used as digital inputs. In this case they are addressed as an additional input port (port 6) via special function register P6 (0DBH) Since port 6 has no internal latch, the contents of SFR P6 only depends on the levels applied to the input lines. For details about this port please refer to section 7.1 (Parallel I/O). The contents of the internal RAM of the SAB 80(C)515 is not affected by a reset. After power-up the contents is undefined, while it remains unchanged during a reset if the power supply is not turned off.
Semiconductor Group
32
System Reset
Table 6-1 Register Contents after Reset Register P0 - P5 DPTR TCON TL0, TH0 TL2, TH2 IEN0, IEN1 IRCON CCL1, CCH1 CCL3, CCH3 T2CON ADCON DAPR B PC Contents 0FFH 0000H 00H 00H 00H 00H 00H 00H 00H 00H 00X0 0000B 00H 00H 0000H Register SP PCON TMOD TL1, TH1 SCON SBUF IP0 IP1 CCEN CCL2, CCH2 CRCL, CRCH PSW ADDAT ACC Watchdog Contents 07H 000X 0000B 00H 00H 00H undefined X000 0000B XX00 0000B 00H 00H 00H 00H 00H 00H 0000H
Semiconductor Group
33
System Reset
6.1.2
Hardware Reset Timing
This section describes the timing of the hardware reset signal. The input pin RESET is sampled once during each machine cycle. This happens in state 5 phase 2. Thus, the external reset signal is synchronized to the internal CPU timing. When the reset is found active (low level at pin 10) the internal reset procedure is started. lt needs two complete machine cycles to put the complete device to its correct reset state. i.e. all special function registers contain their default values, the port latches contain 1's etc. Note that this reset procedure is not performed if there is no clock available at the device. The RESET signal must be active for at least two machine cycles; after this time the SAB 80(C)515 remains in its reset state as long as the signal is active. When the signal goes inactive this transition is recognized in the following state 5 phase 2 of the machine cycle. Then the processor starts its address output (when configured for external ROM) in the following state 5 phase 1. One phase later (state 5 phase 2) the first falling edge at pin ALE occurs. Figure 6-2 shows this timing for a configuration with EA = 0 (external program memory). Thus, between the release of the RESET signal and the first falling edge at ALE there is a time period of at least one machine cycle but less than two machine cycles.
One Machine Cycle S4 S5 S6 S1 P1 P2 S2 S3 S4 S5 S6 S1 S2 S3 S4 S5 S6 S1 S2
RESET
P0
PCL OUT PCH OUT
Inst. PCL IN OUT PCH OUT
P2
ALE
MCT01879
Figure 6-2 CPU Timing after RESET
Semiconductor Group
34
On-Chip Peripheral Components
7
On-Chip Peripheral Components
This chapter gives detailed information about all on-chip peripherals of the SAB 80(C)515 except for the integrated interrupt controller, which is described separately in chapter 8. Sections 7.1 and 7.2 are associated with the general parallel and serial I/O facilities while the remaining sections describe the miscellaneous functions such as the timers, serial interface, A/D converter, power saving modes, watchdog timer, oscillator and clock circuitries, and system clock output. 7.1 7.1.1 Parallel I/O Port Structures
Digital I/O The SAB 80(C)515 allows for digital I/O on 48 lines grouped into 6 bidirectional 8-bit ports. Each port bit consists of a latch, an output driver and an input buffer. Read and write accesses to the I/O ports P0 through P5 are performed via their corresponding special function registers P0 to P5. The output drivers of port 0 and 2 and the input buffers of port 0 are also used for accessing external memory. In this application, port 0 outputs the low byte of the external memory address, timemultiplexed with the byte being written or read. Port 2 outputs the high byte of the external memory address when the address is 16 bits wide. Otherwise, the port 2 pins continue emitting the P2 SFR contents (see also chapter 7.1.2 and chapter 5 for more details about the external bus interface). Digital/Analog Input Ports The analog input lines AN0 to AN7 of the MYMOS versions can only be used as analog inputs. In the ACMOS versions these lines may also be used as digital inputs. In this case they are addressed as an additional input port (port 6) via special function register P6 (0DBH). Since port 6 has no internal latch, the contents of SFR P6 only depends on the levels applied to the input lines. When used as analog input the required analog channel is selected by a three-bit field in SFR ADCON , as described in section 7.4. Of course, it makes no sense to output a value to these inputonly ports by writing to the SFR P6 or P8; this will have no effect.
Semiconductor Group
35
On-Chip Peripheral Components
lf a digital value is to be read, the voltage levels are to be held within the input voltage specifications (VIL/VIH). Since P6 is not a bit-addressable register, all input lines of P6 are read at the same time by byte instructions. Nevertheless, it is possible to use port 6 simultaneously for analog and digital input. However, care must be taken that all bits of P6 are masked which have an undetermined value caused by their analog function . In order to guarantee a high-quality A/D conversion, digital input lines of port 6 should not toggle while a neighbouring port pin is executing an A/D conversion. This could produce crosstalk to the analog signal. 7.1.1.1 Digital I/O Port Circuitry (MYMOS/ACMOS) Figure 7-1 shows a functional diagram of a typical bit latch and I/O buffer, which is the core of each of the 6 I/O-ports. The bit latch (one bit in the port's SFR) is represented as a type-D flip-flop, which will clock in a value from the internal bus in response to a "write-to-latch" signal from the CPU. The Q output of the flip-flop is placed on the internal bus in response to a "read-latch" signal from the CPU. The level of the port pin itself is placed on the internal bus in response to a "read-pin" signal from the CPU. Some instructions that read from a port (i.e. from the corresponding port SFR P0 to P5) activate the "read-latch" signal, while others activate the "read-pin" signal (see section 7.1.4.3).
Figure 7-1 Basic Structure of a Port Circuitry Semiconductor Group 36
On-Chip Peripheral Components
Port 1 through 5 output drivers have internal pullup FET's (see figure 7-2). Each I/O line can be used independently as an input or output. To be used as an input, the port bit must contain a one (1) (that means for figure 7-2: Q = 0), which turns off the output driver FET n1. Then, for ports 1 through 5, the pin is pulled high by the internal pullups, but can be pulled low by an external source. When externally pulled low the port pins source current (IIL or ITL). For this reason these ports are sometimes called "quasi-bidirectional".
Figure 7-2 Basic Output Driver Circuit of Ports 1 through 5 In fact, the pullups mentioned before and included in figure 7-2 are pullup arrangements as shown in figure 7-3. These pullup arrangements are realized differently in the MYMOS and ACMOS versions. In the next two sections both versions are discussed separately.
Semiconductor Group
37
On-Chip Peripheral Components
Figure 7-3 Output Driver Circuits of Ports 1 through 5
Semiconductor Group
38
On-Chip Peripheral Components
7.1.1.2 MYMOS Port Driver Circuitry The output driver circuitry of the MYMOS version (figure 7-3) consists of two pullup FETs (pullup arrangements) and one pulldown FET: - The transistor n1 is a very strong pullup transistor which is only activated for two oscillator periods, if a 0-to-1 transition is executed by this port bit. Transistor n1 is capable of driving high currents. - The transistor n2 is a weak pullup transistor, which is always switched on. When the pin is pulled down (e.g. when the port is used as input), it sources a low current. This value can be found as the parameter IIL in the DC characteristics. - The transistor n3 is a very strong pull-down transistor which is switched on when a "0" is programmed to the corresponding port latch. Transistor n3 is capable of sinking high currents (IOL in the DC characteristics). A short circuit to VCC must be avoided if the transistor is turned on because the high current might destroy the FET. 7.1.1.3 ACMOS Port Driver Circuitry The output driver circuitry of the ACMOS version (figure 7-3) is realized by three pullup FETs (pullup arrangement) and one pulldown FET: - The pulldown FET n1 is of n-channel type. lt is a very strong driver transistor which is capable of sinking high currents (IOL); it is only activated if a "0" is programmed to the port pin. A short circuit to VCC must be avoided if the transistor is turned on, since the high current might destroy the FET. - The pullup FET p1 is of p-channel type. lt is activated for two oscillator periods (S1P1 and S1P2) if a 0-to-1 transition is programmed to the port pin, i.e. a "1" is programmed to the port latch which contained a "0". The extra pullup can drive a similar current as the pulldown FET n1. This provides a fast transition of the logic levels at the pin. - The pullup FET p2 is of p-channel type. lt is always activated when a "1" is in the port latch, thus providing the logic high output level. This pullup FET sources a much lower current than p1; therefore the pin may also be tied to ground, e.g. when used as input with logic low input level. - The pullup FET p3 is of p-channel type. lt is only activated if the voltage at the port pin is higher than approximately 1.0 to 1.5 V. This provides an additional pullup current if a logic high level is to be output at the pin (and the voltage is not forced lower than approximately 1.0 to 1.5 V). However, this transistor is turned off if the pin is driven to a logic low level, e.g. when used as input. In this configuration only the weak pullup FET p2 is active, which sources the current IIL. lf, in addition, the pullup FET p3 is activated, a higher current can be sourced (ITL). Thus, an additional power consumption can be avoided if port pins are used as inputs with a low level applied. However, the driving cabability is stronger if a logic high level is output. The described activating and deactivating of the four different transistors translates into four states the pins can be: - - - - input low state (IL), p2 active only input high state (IH) = steady output high state (SOH) p2 and p3 active forced output high state (FOH), p1, p2 and p3 active output low state (OL), n1 active
Semiconductor Group
39
On-Chip Peripheral Components
If a pin is used as input and a low level is applied, it will be in IL state, if a high level is applied, it will switch to IH state. If the latch is loaded with "0", the pin will be in OL state. If the latch holds a "0" and is loaded with "1", the pin will enter FOH state for two cycles and then switch to SOH state. If the latch holds a "1" and is reloaded with a "1" no state change will occur. At the beginning of power-on reset the pins will be in IL state (latch is set to "1", voltage level on pin is below of the trip point of p3). Depending on the voltage level and load applied to the pin, it will remain in this state or will switch to IH (=SOH) state. If it is used as output, the weak pull-up p2 will pull the voltage level at the pin above p3's trip point after some time and p3 will turn on and provide a strong "1". Note, however, that if the load exceeds the drive capability of p2 (IIL), the pin might remain in the IL state and provide a week "1" until the first 0-to-1 transition on the latch occurs. Until this the output level might stay below the trip point of the external circuitry. The same is true if a pin is used as bidirectional line and the external circuitry is switched from outpout to input when the pin is held at "0" and the load then exceeds the p2 drive capabilities. If the load exceeds IIL the pin can be forced to "1" by writing a "0" followed by a "1" to the port pin. Port 0, in contrast to ports 1 through 5, is considered as "true" bidirectional, because the port 0 pins float when configured as inputs. Thus, this port differs in not having internal pullups. The pullup FET in the P0 output driver (see figure 7-4 a) ) is used only when the port is emitting 1 s during the external memory accesses. Otherwise, the pullup is always off. Consequently, P0 lines that are used as output port lines are open drain lines. Writing a "1" to the port latch leaves both output FETs off and the pin floats. In that condition it can be used as high-impedance input. lf port 0 is configured as general I/O port and has to emit logic high level (1), external pullups are required.
Figure 7-4 a) Port 0 Circuitry Semiconductor Group 40
On-Chip Peripheral Components
7.1.2
Port 0 and Port 2 Used as Address/Data Bus
As shown in figures 7-4 a) and 7-4 b), the output drivers of ports 0 and 2 can be switched to an internal address or address/data bus for use in external memory accesses. In this application they cannot be used as general purpose I/O, even if not all address lines are used externally. The switching is done by an internal control signal dependent on the input level at the EA pin and/or the contents of the program counter. lf the ports are configured as an address/data bus, the port latches are disconnected from the driver circuit. During this time, the P2 SFR remains unchanged while the P0 SFR has 1's written to it. Being an address/data bus, port 0 uses a pullup FET as shown in figure 7-4 a). When a 16-bit address is used, port 2 uses the additional strong pullups p1 to emit 1's for the entire external memory cycle instead of the weak ones (p2 and p3) used during normal port activity.
Figure 7-4 b) Port 2 Circuitry
Semiconductor Group
41
On-Chip Peripheral Components
7.1.3
Alternate Functions
Several pins of ports 1 and 3 are multifunctional. They are port pins and also serve to implement special features as listed in table 7-1. Table 7-1 Port P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 Pin INT3/CC0 INT4/CC1 INT5/CC2 INT6/CC3 INT2 T2EX CLKOUT T2 RXD TXD INT0 INT1 T0 T1 WR RD Alternate Function Ext. interrupt 3 input, compare 0 output, capture 0 input Ext. interrupt 4 input, compare 1 output, capture 1 input Ext. interrupt 5 input, compare 2 output, capture 2 input Ext. interrupt 6 input, compare 3 output, capture 3 input Ext. interrupt 2 input Timer 2 external reload trigger input System clock output Timer 2 external reload trigger input Serial port's receiver data input (asynchronous) or data input/output (synchronous) Serial port's transmitter data output (asynchronous) or clock output (synchronous) External interrupt 0 input, timer 0 gate control External interrupt 1 input, timer 1 gate control Timer 0 external counter input Timer 1 external counter input External data memory write strobe External data memory read strobe
Semiconductor Group
42
On-Chip Peripheral Components
Figure 7-5 shows a functional diagram of a port latch with alternate function. To pass the alternate function to the output pin and vice versa, however, the gate between the latch and driver circuit must be open. Thus, to use the alternate input or output functions, the corresponding bit latch in the port SFR has to contain a one (1); otherwise the pull-down FET is on and the port pin is stuck at 0. (This does not apply to ports 1.0 to 1.3 when operated in compare output mode; refer to section 7.5.2 for details). After reset all port latches contain ones (1).
Figure 7-5 Port 1 and 3
Semiconductor Group
43
On-Chip Peripheral Components
7.1.4
Port Handling
7.1.4.1 Port Timing When executing an instruction that changes the value of a port latch, the new value arrives at the latch during S6P2 of the final cycle of the instruction. However, port latches are only sampled by their output buffers during phase 1 of any clock period (during phase 2 the output buffer holds the value it noticed during the previous phase 1). Consequently, the new value in the port latch will not appear at the output pin until the next phase 1, which will be at S1P1 of the next machine cycle. When an instruction reads a value from a port pin (e.g. MOV A, P1) the port pin is actually sampled in state 5 phase 1 or phase 2 depending on port and alternate functions. Figure 7-6 illustrates this port timing. lt must be noted that this mechanism of sampling once per machine cycle is also used if a port pin is to detect an "edge", e.g. when used as counter input. In this case an "edge" is detected when the sampled value differs from the value that was sampled the cycle before. Therefore, there must be met certain requirements on the pulse length of signals in order to avoid signal "edges" not being detected. The minimum time period of high and low level is one machine cycle, which guarantees that this logic level is noticed by the port at least once.
Figure 7-6 Port Timing
Semiconductor Group
44
On-Chip Peripheral Components
7.1.4.2 Port Loading and Interfacing The output buffers of ports 1 through 5 can drive TTL inputs directly. The maximum port load which still guarantees correct logic output levels can belooked up in the DC characteristics in the Data Sheet of the SAB 80(C)515. The corresponding parameters are VOL and VOH. The same applies to port 0 output buffers. They do, however, require external pullups to drive floating inputs, except when being used as the address/data bus. When used as inputs it must be noted that the ports 1 through 5 are not floating but have internal pullup transistors. The driving devices must be capable of sinking a sufficient current if a logic low level shall be applied to the port pin (the parameters ITL and IIL in the DC characteristics specify these currents). Port 0 as well as the input only ports 6 of the ACMOS versions have floating inputs when used for digital input. 7.1.4.3 Read-Modify-Write Feature of Ports 0 through 5 Some port-reading instructions read the latch and others read the pin (see figure 7-1). The instructions reading the latch rather than the pin read a value, possibly change it, and then rewrite it to the latch. These are called "read-modify-write" instructions, which are listed in table 7-2. lf the destination is a port or a port bit, these instructions read the latch rather than the pin. Note that all other instructions which can be used to read a port, exclusively read the port pin. In any case, reading from latch or pin, resp., is performed by reading the SFR P0 to P5; for example, "MOV A, P3" reads the value from port 3 pins, while "ANL P4, #0AAH" reads from the latch, modifies the value and writes it back to the latch.
Semiconductor Group
45
On-Chip Peripheral Components
Table 7-2 Read-Modify-Write Instructions Instruction ANL ORL XRL JBC CPL INC DEC DJNZ MOV Px.y, C CLR Px.y SETB Px.y Function Logic AND; e.g. ANL P1, A Logic OR; e.g. ORL P2, A Logic exclusive OR; e.g. XRL P3, A Jump if bit is set and clear bit; e.g. JBC P1.1, LABEL Complement bit; e.g. CPL P3.0 Increment byte; e.g. INC P4 Decrement byte; e.g. DEC P5 Decrement and jump if not zero; e.g. DJNZ P3, LABEL Move carry bit to bit y of port x Clear bit y of port x Set bit y of port x
lt is not obvious that the last three instructions in this list are read-modify-write instructions, but they are. The reason is that they read the port byte, all 8 bits, modify the addressed bit, then write the complete byte back to the latch. The reason why read-modify-write instructions are directed to the latch rather than the pin is to avoid a possible misinterpretation of the voltage level at the pin. For example, a port bit might be used to drive the base of a transistor. When a "1" is written to the bit, the transistor is turned on. lf the CPU then reads the same port bit at the pin rather than the latch, it will read the base voltage of the transistor (approx. 0.7 V, i.e. a logic low level !) and interpret it as "0". For example, when modifying a port bit by a SETB or CLR instruction, another bit in this port with the above mentioned configuration might be changed if the value read from the pin were written back to the latch. However, reading the latch rather than the pin will return the correct value of "1".
Semiconductor Group
46
On-Chip Peripheral Components
7.2
Serial Interfaces
The serial port of the SAB 80(C)515S enables communication between microcontrollers or between the microcontroller and peripheral devices. The serial port is full-duplex, meaning it can transmit and receive simultaneously. It is also receive buffered, meaning it can commence reception of a second byte before a previously received byte has been read from the receive register (however, if the first byte still has not been read by the time reception of the second byte is complete, the last received byte will be lost). The serial channel is completely compatible with the serial channel of the SAB 80(C)51. 7.2.1 Operating Modes of Serial Interface
The serial interface can operate in four modes (one synchronous mode, three asynchronous modes). The baud rate clock for this interface is derived from the oscillator frequency (mode 0, 2) or generated either by timer 1 or by a dedicated baud rate generator (mode 1, 3). A more detailed description of how to set the baud rate will follow in section 7.2.3. Mode 0: shift register (synchronous) mode: Serial data enters and exits through RxD. TxD outputs the shift clock. 8 data bits are transmitted/ received (LSB first). The baud rate is fixed at 1/12 of the oscillator frequency. Mode 1: 8-bit UART, variable baud rate: 10 bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), and a stop bit (1). On reception, the stop bit goes into RB8 in special function register SCON. The baud rate is variable. Mode 2: 9-bit UART, fixed baud rate: 11 bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), a programmable 9th bit, and a stop bit (1). On transmission, the 9th data bit (TB8 in SCON) can be assigned to the value of 0 or 1. For example, the parity bit (P in the PSW) could be moved into TB8 or a second stop bit by setting TB8 to 1. On reception the 9th data bit goes into RB8 in special function register SCON, while the stop bit is ignored. The baud rate is programmable to either 1/32 or 1/64 of the oscillator frequency. Mode 3: 9-bit UART, variable baud rate: 11 bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), a programmable 9th bit, and a stop bit (1). On transmission, the 9th data bit (TB8 in SCON) can be assigned to the value of 0 or 1. For example, the parity bit (P in the PSW) could be moved into TB8 or a second stop bit by setting TB8 to 1. On reception, the 9th data bit goes into RB8 in special function register SCON, while the stop bit is ignored. In fact, mode 3 is the same as mode 2 in all respects except the baud rate. The baud rate in mode 3 is variable.
Semiconductor Group
47
On-Chip Peripheral Components
In all four modes, transmission is initiated by any instruction that uses SBUF as a destination register. Reception is initiated in mode 0 by the condition RI = 0 and REN = 1. Reception is initiated in the other modes by the incoming start bit if REN = 1. The serial interfaces also provide interrupt requests when a transmission or a reception of a frame has completed. The corresponding interrupt request flags for serial interface are TI or RI, resp. See section 8 for more details about the interrupt structure. The interrupt request flags TI and RI can also be used for polling the serial interface if the serial interrupt is not to be used (i.e. serial interrupt not enabled). The control and status bits of the serial channel 0 in special function register S0CON are illustrated in figure 7-8. Figure 7-7 shows the special function register S0BUF which is the data register for receive and transmit. The following table summarizes the operating modes of serial interface 0.
Figure 7-7 Special Function Register SCON (Address 98H) 9FH 98H Bit SM0 0 0 1 1 SM2 SM1 0 1 0 1 SM0 9EH SM1 9DH SM2 9CH REN 9BH TB8 9AH RB8 99H TI 98H RI SCON
Symbol Serial mode 0: Serial mode 1: Serial mode 2: Serial mode 3: Shift register mode, fixed baud rate 8-bit UART, variable baud rate 9-bit UART, fixed baud rate 9-bit UART, variable baud rate
Enables the multiprocessor communication feature in modes 2 and 3. In mode 2 or 3 and SM2 being set to 1, RI will not be activated if the received 9th data bit (RB8) is 0. In mode 1 and SM2 = 1, RI will not be activated if a valid stop bit has not been received. In mode 0, SM2 should be 0. Receiver enable. Enables serial reception. Set by software to enable reception. Cleared by software to disable reception. Transmitter bit 8. Is the 9th data bit that will be transmitted in modes 2 and 3. Set or cleared by software as desired. Receiver bit 8. In modes 2 and 3 it is the 9th bit that was received. In mode 1, if SM2 = 0, RB8 is the stop bit that was received. In mode 0, RB8 is not used. Transmitter interrupt. Is the transmit interrupt flag. Set by hardware at the end of the 8th bit time in mode 0, or at the beginning of the stop bit in the other modes, in any serial transmission. Must by cleared by software. Receiver interrupt. Is the receive interrupt flag. Set by hardware at the end of the 8th bit time in mode 0, or during the stop bit time in the other modes, in any serial reception. Must be cleared by software.
REN TB8 RB8
TI
RI
Semiconductor Group
48
On-Chip Peripheral Components
The control and status bits of the serial channel in special function register SCON are illustrated in figure 7-8. Figure 7-7 shows the special function register SBUF which is the data register for receive and transmit. The following table summarizes the operating modes of the serial interface.
Table 7-3 Serial Interface, Mode Selection SM0 0 0 1 1 SM1 0 1 0 1 Mode 0 1 2 3 Descriptions Shift register 8-bit UART 9-bit UART 9-bit UART Baud Rate
fOSC/12
Variable
fOSC/64 or fOSC/32
Variable
Figure 7-8 Special Function Register SBUF (Address 99H) 99H Serial interface buffer register SBUF
Receive and transmit buffer of serial interface. Writing to SBUF loads the transmit register and initiates transmission. Reading out SBUF accesses a physically separate receive register.
Semiconductor Group
49
On-Chip Peripheral Components
7.2.2
Multiprocessor Communication Feature
Modes 2 and 3 of the serial interface 0 have a special provision for multi-processor communication. In these modes, 9 data bits are received. The 9th bit goes into RB8. Then a stop bit follows. The port can be programmed such that when the stop bit is received, the serial port 0 interrupt will be activated (i.e. the request flag RI is set) only if RB8 = 1. This feature is enabled by setting bit SM2 in SCON. A way to use this feature in multiprocessor communications is as follows. lf the master processor wants to transmit a block of data to one of the several slaves, it first sends out an address byte which identifies the target slave. An address byte differs from a data byte in that the 9th bit is 1 in an address byte and 0 in a data byte. With SM2 = 1, no slave will be interrupted by a data byte. An address byte, however, will interrupt all slaves, so that each slave can examine the received byte and see if it is being addressed. The addressed slave will clear its SM2 bit and prepare to receive the data bytes that will be coming. After having received a complete message, the slave sets SM2 again. The slaves that were not addressed leave their SM2 set and go on about their business, ignoring the incoming data bytes. SM2 has no effect in mode 0. In mode 1 SM2 can be used to check the validity of the stop bit. lf SM2 = 1 in mode 1, the receive interrupt will not be activated unless a valid stop bit is received. 7.2.3 Baud Rates
As already mentioned there are several possibilities to generate the baud rate clock for the serial interface depending on the mode in which it is operated. To clarify the terminology, something should be said about the difference between "baud rate clock" and "baud rate". The serial interface requires a clock rate which is 16 times the baud rate for internal synchronization, as mentioned in the detailed description of the various operating modes in section 7.2.4. Therefore, the baud rate generator have to provide a "baud rate clock" to the serial interface which there divided by 16 - results in the actual "baud rate". However, all formulas given in the following section already include the factor and calculate the final baud rate.
Semiconductor Group
50
On-Chip Peripheral Components
Mode 0 The baud rate in mode 0 is fixed: Mode 0 baud rate = oscillator frequency 12
Mode 2 The baud rate in mode 2 depends on the value of bit SMOD in special function register PCON (see figure 7-9). If SMOD = 0 (which is the value after reset), the baud rate is 1/64 of the oscillator frequency. If SMOD = 1, the baud rate is 1/32 of the oscillator frequency. Mode 2 baud rate = 2SMOD 64 x oscillator frequency
Figure 7-9 Special Function Register PCON (Address 87H)
87H SMOD
PDS
IDLS
-
GF1
GF0
PDE
IDLE
PCON
These bits are not used in controlling serial interface.
Bit SMOD Modes 1 and 3
Function When set, the baud rate of serial interface in modes 1, 2, 3 is doubled.
In these modes the baud rate is variable and can be generated alternatively by a dedicated baud rate generator or by timer 1. Using the baud rate generator: In modes 1 and 3, the SAB 80(C)515 can use the internal baud rate generator for the serial interface. To enable this feature, bit BD (bit 7 of special function register ADCON) must be set (see figure 7-10). This baud rate generator divides the oscillator frequency by 2500. Bit SMOD (PCON.7) also can be used to enable a multiply by two prescaler (see figure 7-9). At 12-MHz oscillator frequency, the commonly used baud rates 4800 baud (SMOD = 0) and 9600 baud (SMOD = 1) are available. The baud rate is determined by SMOD and the oscillator frequency as follows: 2SMOD 2500
Mode 1, 3 baud rate =
x oscillator frequency
Semiconductor Group
51
On-Chip Peripheral Components
Figure 7-10 Special Function Register ADCON (Address 0D8H) 0DFH 0D8H BD 0DEH CLK 0DDH ADEX 0DCH BSY 0DBH ADM 0DAH MX2 0D9H MX1 0D8H MX0 ADCON
These bits are not used in controlling serial interface.
Bit BD
Function Baud rate enable. When set, the baud rate in modes 1 and 3 of serial interface is taken from a dedicated prescaler. Standard baud rates 4800 and 9600 baud at 12-MHz oscillator frequency can be achieved.
Using timer 1 to generate baud rates: Timer 1 can be used for generating baud rates in mode 1 and 3 of the serial channel. Then the baud rate is determined by the timer 1 overflow rate and the value of SMOD as follows: Mode 1, 3 baud rate = 2SMOD 32 x (Timer 1 OV-rate)
The timer 1 interrupt is usually disabled in this application. The timer itself can be configured for either "timer" or "counter" operation, and in any of its operating modes. In the most typical applications, it is configured for "timer" operation in the auto-reload mode (high nibble of TMOD = 0010B). In the case, the baud rate is given by the formula: Mode 1, 3 baud rate = 2SMOD x oscillator frequency 32 x 12 x (256 - (TH1))
One can achieve very low baud rates with timer 1 by leaving the timer 1 interrupt enabled, configuring the timer to run as 16-bit timer (high nibble of TMOD = 0001B), and using the timer 1 interrupt for a 16-bit software reload. Table 7-4 lists various commonly used baud rates and shows how they can be obtained from timer 1.
Semiconductor Group
52
On-Chip Peripheral Components
Table 7-4 Timer 1 Generated Commonly Used Baud Rates Baud Rate
fOSC (MHz)
SMOD C/T
Timer 1 Mode 2 2 2 2 2 2 2 1 Reload Value FFH FDH FDH FAH F4H E8H 72H FEEBH
Mode 1, 3:
62.5 Kbaud 19.5 Kbaud 9.6 Kbaud 4.8 Kbaud 2.4 Kbaud 1.2 Kbaud 110 Baud 110 Baud
12.0 11.059 11.059 11.059 11.059 11.059 6.0 12.0
1 1 0 0 0 0 0 0
0 0 0 0 0 0 0 0
Figure 7-11 shows the mechanisms for baud rate generation of serial channel, while table 7-5 summarizes the baud rate formulas for all usual configurations.
Figure 7-11 Generation of Baud Rates for Serial Interface
Semiconductor Group
53
On-Chip Peripheral Components
Table 7-5 Baud Rates of Serial Interface 0 Baud Rate Derived from Timer 1 in mode 1 Interface Mode 1, 3 Baud Rate 2SMOD 2 Timer 1 in mode 2 1, 3 2SMOD 2 Oscillator 2 2SMOD 2 Baud rate generator 1, 3 2SMOD 2 1 16 1 16 1 16 1 16 x (timer 1 overflow rate)
x
x
x
fOSC
12 x (256 - (TH1))
x
x
fOSC
2
x
x
fOSC
1250
7.2.4
Detailed Description of the Operating Modes
The following sections give a more detailed description of the several operating modes of the serial interface. 7.2.4.1 Mode 0, Synchronous Mode Serial data enters and exits through RxD. TxD outputs the shift clock. 8 bits are transmitted/ received: 8 data bits (LSB first). The baud rate is fixed at 1/12 of the oscillator frequency. Figures 7-16 a) and b) show a simplified functional diagram of the serial port in mode 0, and associated timing. Transmission is initiated by any instruction that uses SBUF as a destination register. The "write-toSBUF" signal at S6P2 also loads a 1 into the 9th bit position of the transmit shift register and tells the TX control block to commence a transmission. The internal timing is such that one full machine cycle will elapse between "write-to-SBUF" and activation of SEND.
Semiconductor Group
54
On-Chip Peripheral Components
SEND enables the output of the shift register to the alternate output function line P3.0, and also enables SHIFT CLOCK to the alternate output function line P3.1. SHIFT CLOCK is low during S3, S4, and S5 of every machine cycle, and high during S6, S1, and S2, while the interface is transmitting. Before and after transmission SHIFT CLOCK remains high. At S6P2 of every machine cycle in which SEND is active, the contents of the transmit shift register is shifted one position to the right. As data bits shift to the right, zeros come in from the left. When the MSB of the data byte is at the output position of the shift register, then the 1 that was initially loaded into the 9th position, is just left of the MSB, and all positions to the left of that contain zeros. This condition flags the TX control block to do one last shift and then deactivates SEND and sets TI. Both of these actions occur at S1P1 in the 10th machine cycle after "write-to-SBUF". Reception is initiated by the condition REN = 1 and RI = 0. At S6P2 in the next machine cycle, the RX control unit writes the bits 1111 1110 to the receive shift register, and in the next clock phase activates RECEIVE. RECEIVE enables SHIFT CLOCK to the alternate output function line of P3.1. SHIFT CLOCK makes transitions at S3P1 and S6P1 in every machine cycle. At S6P2 of every machine cycle in which RECEIVE is active, the contents of the receive shift register are shifted one position to the left. The value that comes in from the right is the value that was sampled at the P3.0 pin at S5P2 in the same machine cycle. As data bits come in from the right, 1 s shift out to the left. When the 0 that was initially loaded into the rightmost position arrives at the leftmost position in the shift register, it flags the RX control block to do one last shift and load SBUF. At S1P1 in the 10th machine cycle after the write to SCON that cleared RI, RECEIVE is cleared and RI is set. 7.2.4.2 Mode 1, 8-Bit UART Ten bits are transmitted (through TxD), or received (through RxD): a start bit (0), 8 data bits (LSB first), and a stop bit (1). On reception through RxD, the stop bit goes into RB8 (SCON). The baud rate for serial interface 0 is determined by the timer 1 overflow rate or by the internal baud rate generator. Figures 7-17 a) and b) show a simplified functional diagram of the serial channel in mode 1. The generation of the baud rate clock is described in section 7.2.3.
Semiconductor Group
55
On-Chip Peripheral Components
Transmission is initiated by any instruction that uses SBUF as a destination register. The "write-toSBUF" signal also loads a 1 into the 9th bit position of the transmit shift register and flags the TX control block that a transmission is requested. Transmission actually commences at S1P1 of the machine cycle following the next roll-over in the divide-by-16 counter (thus, the bit times are synchronized to the divide-by-16 counter, not to the "write-to-SBUF" signal). The transmission begins with activation of SEND, which puts the start bit to TxD. One bit time later, DATA is activated, which enables the output bit of the transmit shift register to TxD. The first shift pulse occurs one bit time after that. As data bits shift out to the right, zeros are clocked in from the left. When the MSB of the data byte is at the output position of the shift register, then the 1 that was initially loaded into the 9th position, is just left of the MSB, and all positions to the left of that contain zero. This condition flags the TX control to do one last shift and then deactivates SEND and sets TI. This occurs at the 10th divideby-16 rollover after "write-to-SBUF". Reception is initiated by a detected 1-to-0 transition at RxD. For this purpose RxD is sampled at a rate of 16 times whatever baud rate has been established. When a reception is detected, the divideby-16 counter is immediately reset, and 1FFH is written into the input shift register. Resetting the divide-by-16 counter aligns its rollover with the boundaries of the incoming bit times. The 16 states of the counter divide each bit time into 16 counter states. At the 7th, 8th and 9th counter state of each bit time, the bit detector samples the value of RxD. The value accepted is the value that was seen in at least 2 of the 3 samples. This is done for noise rejection. lf the value accepted during the first bit time is not 0, the receive circuits are reset and the unit goes back looking for another 1-to-0 transition. This is to provide rejection of false start bits. lf the start bit proves valid, it is shifted into the input shift register, and reception of the rest of the frame will proceed. As data bits come from the right, 1's shift out to the left. When the start bit arrives at the leftmost position in the shift register (which in mode 1 is a 9-bit register), it flags the RX control block to do one last shift. The signal to load SBUF and RB8 and to set RI will be generated if, and only if, the following conditions are met at the time the final shift pulse is generated: 1) 2) RI = 0, and either SM2 = 0 or the received stop bit = 1
lf either of these two conditions is not met the received frame is irretrievably lost. lf both conditions are met, the stop bit goes into RB8, the 8 data bits go into SBUF, and RI is activated. At this time, no matter whether the above conditions are met or not, the unit goes back to looking for a 1-to-0 transition in RxD.
Semiconductor Group
56
On-Chip Peripheral Components
7.2.4.3 Mode 2, 9-Bit UART Mode 2 is functionally identical to mode 3 (see below). The only exception is, that in mode 2 the baud rate can be programmed to two fixed quantities: either 1/32 or 1/64 of the oscillator frequency. In mode 3 the baud rate clock is generated by timer 1, which is incremented by a rate of fOSC/12 or by the internal baud rate generator. 7.2.4.4 Mode 3, 9-Bit UART Eleven bits are transmitted (through TxD), or received (through RxD): a start bit (0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). On transmission, the 9th data bit (TB8) can be assigned the value of 0 or 1. On reception the 9th data bit goes into RB8 in SCON. The baud rate is generated by either using timer 1 or the internal baud rate generator (see section 7.2.3). Figures 7-18 a) and b) show a functional diagram of the serial interfaces in mode 2 and 3 and associated timing. The receive portion is exactly the same as in mode 1. The transmit portion differs from mode 1 only in the 9th bit of the transmit shift register. Transmission is initiated by any instruction that uses SBUF as a destination register. The "write to SBUF" signal also loads TB8 into the 9th bit position of the transmit shift register and flags the TX control unit that a transmission is requested. Transmission commences at S1P1 of the machine cycle following the next rollover in the divide-by-16 counter (thus the bit times are synchronized to the divide-by-16 counter, and not to the "write-to-SBUF" signal). The transmission begins with the activation of SEND, which puts the start bit to TxD. One bit time later, DATA is activated which enables the output bit of transmit shift register to TxD. The first shift pulse occurs one bit time after that. The first shift clocks a 1 (the stop bit) into the 9th bit position of the shift register. Thereafter, only zeros are clocked in. Thus, as data shift out to the right, zeros are clocked in from the left. When TB8 is at the output position of the shift register, then the stop bit is just left of the TB8, and all positions to the left of that contain zeros. This condition flags the TX control unit to do one last shift and then deactivate SEND and set TI. This occurs at the 11th divide-by-16 rollover after "write-to-SBUF". Reception is initiated by a detected 1-to-0 transition at RxD. For this purpose RxD is sampled of a rate of 16 times whatever baud rate has been established. When a transition is detected, the divideby-16 counter is immediately reset, and 1FH is written to the input shift register.
Semiconductor Group
57
On-Chip Peripheral Components
At the 7th, 8th and 9th counter state of each bit time, the bit detector samples the value of RxD. The value accepted is the value that was seen in at least 2 of the 3 samples. lf the value accepted during the first bit time is not 0, the receive circuits are reset and the unit goes back to looking for another 1-to-0 transition. lf the start bit proves valid, it is shifted into the input shift register, and reception of the rest of the frame will proceed. As data bits come from the right, 1 s shift out to the left. When the start bit arrives at the leftmost position in the shift register (which is a 9-bit register), it flags the RX control block to do one last shift, load SBUF and RB8, and set RI. The signal to load SBUF and RB8, and to set RI, will be generated if, and only if, the following conditions are met at the time the final shift pulse is generated: 1) RI = 0, and 2) either SM2 = 0 or the received 9th data bit = 1 lf either one of these two conditions is not met, the received frame is irretrievably lost, and RI is not set. lf both conditions are met, the received 9th data bit goes into RB8, the first 8 data bits go into SBUF. One bit time later, no matter whether the above conditions are met or not, the unit goes back to look for a 1-to-0 transition at the RxD. Note that the value of the received stop bit is irrelevant to SBUF, RB8, or RI.
Semiconductor Group
58
On-Chip Peripheral Components
Figure 7-16 a) Functional Diagram - Serial Interface, Mode 0
Semiconductor Group
59
On-Chip Peripheral Components
Figure 7-16 b) Timing Diagram - Serial Interface, Mode 0
Semiconductor Group
60
On-Chip Peripheral Components
Figure 7-17 a) Functional Diagram - Serial Interface, Mode 1
Semiconductor Group
61
On-Chip Peripheral Components
Figure 7-17 b) Timing Diagram - Serial Interface, Mode 1
Semiconductor Group
62
On-Chip Peripheral Components
Figure 7-18 a) Functional Diagram - Serial Interface, Modes 2 and 3
Semiconductor Group
63
On-Chip Peripheral Components
Figure 7-18 b) Timing Diagram - Serial Interface, Modes 2 and 3
Semiconductor Group
64
On-Chip Peripheral Components
7.3
Timer 0 and Timer 1
The SAB 80(C)515 three general purpose 16-bit timer/counters: timer 0, timer 1, timer 2 and the compare timer (timer 2 is discussed separately in section 7.5). Timer/counter 0 and 1 are fully compatible with timer/counters 0 and 1 of the SAB 80(C)51 and can be used in the same operating modes. Timer/counter 0 and 1 which are discussed in this section can be configured to operate either as timers or event counters: - In "timer" function, the register is incremented every machine cycle. Thus one can think of it as counting machine cycles. Since a machine cycle consists of 12 oscillator periods, the count rate is 1/12 of the oscillator frequency. - In "counter" function, the register is incremented in response to a 1-to-0 transition (falling edge) at its corresponding external input pin, T0 or T1 (alternate functions of P3.4 and P3.5, resp.). In this function the external input is sampled during S5P2 of every machine cycle. When the samples show a high in one cycle and a low in the next cycle, the count is incremented. The new count value appears in the register during S3P1 of the cycle following the one in which the transition was detected. Since it takes two machine cycles (24 oscillator periods) to recognize a 1-to-0 transition, the maximum count rate is 1/24 of the oscillator frequency. There are no restrictions on the duty cycle of the external input signal, but to ensure that a given level is sampled at least once before it changes, it must be held for at least one full machine cycle. In addition to the "timer" and "counter" selection, timer/counters 0 and 1 have four operating modes from which to select.
Semiconductor Group
65
On-Chip Peripheral Components
Figure 7-19 Special Function Register TCON (Address 88H) 8FH 88H TF1 8EH TR1 8DH TF0 8CH TR0 8BH IE1 8AH IT1 89H IE0 88H IT0 TCON
These bits are not used in controlling timer/counter 0 and 1.
Bit TR0 TF0 TR1 TF1
Function Timer 0 run control bit. Set/cleared by software to turn timer/counter 0 ON/OFF. Timer 0 overflow flag. Set by hardware on timer/counter overflow. Cleared by hardware when processor vectors to interrupt routine. Timer 1 run control bit. Set/cleared by software to turn timer/counter 1 ON/OFF. Timer 1 overflow flag. Set by hardware on timer/counter overflow. Cleared by hardware when processor vectors to interrupt routine.
Each timer consists of two 8-bit registers (TH0 and TL0 for timer/counter 0, TH1 and TL1 for timer/ counter 1) which may be combined to one timer configuration depending on the mode that is established. The functions of the timers are controlled by two special function registers TCON and TMOD, shown in figures 7-19 and 7-20. In the following descriptions the symbols TH0 and TL0 are used specify the high-byte and low-byte of timer 0 (TH1 and TL1 for timer 1, respectively). The operating modes are described and shown for timer 0. If not explicitly noted, this applies also to timer 1.
Semiconductor Group
66
On-Chip Peripheral Components
Figure 7-20 Special Function Register TMOD (Address 89H)
89H
GATE
C/T
M1
M0
GATE
C/T
M1
M0
TMOD
Timer 1 Timer/counter 0/1 mode control register.
Timer 0
Bit Gate
Symbol Gating control. When set, timer/counter "x" is enabled only while "INTx" pin is high and "TRx" control bit is set. When cleared timer "x" is enabled whenever "TRx" control bit is set. Counter or timer select bit. Set for counter operation (input from "Tx" input pin). Cleared for timer operation (input from internal system clock). M0 0 8-bit timer/counter "THx" operates as 8-bit timer/counter "TLx" serves as 5-bit prescaler. 16-bit timer/counter. "THx" and "TLx" are cascaded; there is no prescaler. 8-bit auto-reload timer/counter. "THx" holds a value which is to be reloaded into "TLx" each time it overflows. Timer 0: TL0 is an 8-bit timer/counter controlled by the standard timer 0 control bits. TH00 is an 8-bit timer only controlled by timer 1 control bits. Timer 1: Timer/counter 1 stops
C/T
M1 0
0 1
1 0
1
1
1
1
Semiconductor Group
67
On-Chip Peripheral Components
7.3.1
Mode 0
Putting either timer/counter into mode 0 configures it as an 8-bit timer/counter with a divide-by-32 prescaler. Figure 7-21 shows the mode 0 operation. In this mode, the timer register is configured as a 13-bit register. As the count rolls over from all 1's to all 0's, it sets the timer overflow flag TF0. The overflow flag TF0 then can be used to request an interrupt (see section 8 for details about the interrupt structure). The counted input is enabled to the timer when TR0 = 1 and either GATE = 0 or INT0 = 1 (setting GATE = 1 allows the timer to be controlled by external input INT0, to facilitate pulse width measurements). TR0 is a control bit in the special function register TCON; GATE is in TMOD. The 13-bit register consists of all 8 bits of TH1 and the lower 5 bits of TL0. The upper 3 bits of TL0 are indeterminate and should be ignored. Setting the run flag (TR0) does not clear the registers. Mode 0 operation is the same for timer 0 as for timer 1. Substitute TR1, TF1, TH1, TL1, and INT1 for the corresponding timer 1 signals in figure 7-21. There are two different gate bits, one for timer 1 (TMOD.7) and one for timer 0 (TMOD.3).
Figure 7-21 Timer/Counter 0, Mode 0: 13 Bit-Timer/Counter The same applies to timer/counter 1
Semiconductor Group
68
On-Chip Peripheral Components
7.3.2
Mode 1
Mode 1 is the same as mode 0, except that the timer register is run with all 16 bits. Mode 1 is shown in figure 7-22.
Figure 7-22 Timer/Counter 0, Mode 1: 16-Bit Timer/Counter The same applies to timer/counter 1
Semiconductor Group
69
On-Chip Peripheral Components
7.3.3
Mode 2
Mode 2 configures the timer register as an 8-bit counter (TL0) with automatic reload, as shown in figure 7-23. Overflow from TL0 not only sets TF0, but also reloads TL0 with the contents of TH0, which is preset by software. The reload leaves TH0 unchanged.
Figure 7-23 Timer/Counter 0, Mode 2: 8-Bit Timer/Counter with Auto-Reload The same applies to timer/counter 1
Semiconductor Group
70
On-Chip Peripheral Components
7.3.4
Mode 3
Mode 3 has different effects on timer 0 and timer 1. Timer 1 in mode 3 simply holds its count. The effect is the same as setting TR1 = 0. Timer 0 in mode 3 establishes TL0 and TH0 as two separate counters. The logic for mode 3 on timer 0 is shown in figure 7-24. TL0 uses the timer 0 control bits: C/T, GATE, TR0, INT0, and TF0. TH0 is locked into a timer function (counting machine cycles) and takes over the use of TR1 and TF1 from timer 1. Thus, TH0 now controls the "timer 1" interrupt. Mode 3 is provided for applications requiring an extra 8-bit timer or counter. When timer 0 is in mode 3, timer 1 can be turned on and off by switching it out of and into its own mode 3, or can still be used by the serial channel as a baud rate generator, or in fact, in any application not requiring an interrupt from timer 1 itself.
Figure 7-24 Timer/Counter 0, Mode 3: Two 8-Bit Timers/Counters
Semiconductor Group
71
On-Chip Peripheral Components
7.4
A/D Converter
The SAB 80(C)515 provides an A/D converter with the following features: - Eight multiplexed input channels - The possibility of using the analog input channels (port 6) as digital inputs (ACMOS version only). - Programmable internal reference voltages (16 steps each) via resistor array - 8-bit resolution within the selected reference voltage range - 13 machine cycles conversion time for ACMOS versions (including sample time) - 15 machine cycles conversion time for MYMOS versions (including sample time) - Internal start-of-conversion trigger - Interrupt request generation after each conversion For the conversion, the method of successive approximation via capacitor array is used. The externally applied reference voltage range has to be held on a fixed value within the specifications (see section "A/D Converter Characteristics" in the data sheet). The internal reference voltages can be varied to reduce the reference voltage range of the A/D converter and thus to achieve a higher resolution. Figure 7-25 shows a block diagram of the A/D converter. There are three user-accessible special function registers: ADCON (A/D converter control register), ADDAT (A/D converter data register) and DAPR (D/A converter program register) for the programmable reference voltages.
Semiconductor Group
72
On-Chip Peripheral Components
Figure 7-25 A/D Converter Block Diagram Semiconductor Group 73
On-Chip Peripheral Components
7.4.1
Function and Control
7.4.1.1 lnitialization and Input Channel Selection
Special function register ADCON which is illustrated in figure 7-26 is used to set the operating modes, to check the status, and to select one of eight analog input channels.
Figure 7-26 Special Function Register ADCON (Address 0D8H) 0DFH 0D8H BD 0DEH CLK 0DDH - 0DCH BSY 0DBH ADM 0DAH MX2 0D9H MX1 0D8H MX0 ADCON
These bits are not used in controlling A/D converter functions.
Bit MX0 MX1 MX2 ADM BSY
Function Select 8 input channels of the A/D converter, see table 7-6
A/D conversion mode. When set, a continuous conversion is selected. If ADM = 0, the converter stops after one conversion. Busy flag. This flag indicates whether a conversion is in progress (BSY = 1). The flag is cleared by hardware when the conversion is completed.
Register ADCON contains two mode bits. Bit ADM is used to choose the single or continuous conversion mode. In single conversion mode only one conversion is performed after starting, while in continuous conversion mode after the first start a new conversion is automatically started on completion of the previous one. The busy flag BSY (ADCON.4) is automatically set when a conversion is in progress. After completion of the conversion it is reset by hardware. This flag can be read only, a write has no effect. There is also an interrupt request flag IADC (IRCON.0) that is set when a conversion is completed. See section 8 for more details about the interrupt structure.
Semiconductor Group
74
On-Chip Peripheral Components
Table 7-6 Selection of the Analog Input Channels MX2 0 0 0 0 1 1 1 1 MX1 0 0 1 1 0 0 1 1 MX0 0 1 0 1 0 1 0 1 Selected Channel MYMOS Analog input 0 Analog input 1 Analog input 2 Analog input 3 Analog input 4 Analog input 5 Analog input 6 Analog input 7 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 Pin ACMOS P6.0 P6.1 P6.2 P6.3 P6.4 P6.5 P6.6 P6.7
The bits MX0 to MX2 in special function register ADCON are used for selection of the analog input channels. Port 6 of the ACMOS versions is a dual purpose input port. lf the input voltage meets the specified logic levels, it can be used as digital input as well regardless of whether the pin levels are sampled by the A/D converter at the same time. The special function register ADDAT (figure 7-28) holds the converted digital 8-bit data result. The data remains in ADDAT until it is overwritten by the next converted data. ADDAT can be read or written under software control. lf the A/D converter of the SAB 80(C)515 is not used, register ADDAT can be used as an additional general purpose register.
Figure 7-28 Special Function Register ADDAT (Address 0D9H) 0D9H Conversion result ADDAT
This register contains the 8-bit conversion result. 7.4.1.2 Start of Conversion An internal start of conversion is triggered by a write-to-DAPR instruction. The start procedure itself is independent of the value which is written to DAPR. However, the value in DAPR determines which internal reference voltages are used for the conversion (see section 7.4.2). When single conversion mode is selected (ADM = 0) only one conversion is performed. In continuous mode after completion of a conversion a new conversion is triggered automatically, until bit ADM is reset.
Semiconductor Group
75
On-Chip Peripheral Components
7.4.2
Reference Voltages
The SAB 80(C)515 has two pins to which a reference voltage range for the on-chip A/D converter is applied (pin VAREF for the upper voltage and pin VAGND for the lower voltage). In contrast to conventional A/D converters it is now possible to use not only these externally applied reference voltages for the conversion but also internally generated reference voltages which are derived from the externally applied ones. For this purpose a resistor ladder provides 16 equidistant voltage levels between VAREF and VAGND. These steps can individually be assigned as upper and lower reference voltage for the converter itself. These internally generated reference voltages are called VlntAREF and VlntAGND. The internal reference voltage programming can be thought of as a programmable "D/A converter" which provides the voltages VIntARFF and VIntAGND for the A/D converter itself. The SFR DAPR (see figure 7-29) is provided for programming the internal reference voltages
VIntAREF and VlntAGND. For this purpose the internal reference voltages can be programmed in steps of 1/16 of the external reference voltages (VAREF - VAGND) by four bits each in register DAPR. Bits 0 to 3 specify VlntAGND, while bits 4 to 7 specify VIntAREF. A minimum of 1 V difference is required between the internal reference voltages VlntARF and VIntAGND for proper operation of the A/D converter. This means, for example, in the case where VAREF is 5 V and VAGND is 0 V, there must be at least four steps difference between the internal reference voltages VIntAREF and VIntAGND.
The values of VIntAGND and VIntAREF are given by the formulas: DAPR (.3-.0) 16
VIntAGND = VAGND +
(VAREF - VAGND)
with DAPR (.3-.0) < CH;
VIntAREF = VAGND +
DAPR (.7-.4)
16 with DAPR (.7-.4) > 3H;
(VAREF - VAGND)
DAPR (.3-.0) is the contents of the low-order nibble, and DAPR (.7-.4) the contents of the high-order nibble of DAPR.
Semiconductor Group
76
On-Chip Peripheral Components
If DAPR (.3-.0) or DAPR (.7-.4) = 0, the internal reference voltages correspond to the external reference voltages VAGND and VAREF, respectively. If VAINPUT > VIntAREF, the conversion result is 0FFH, if VAINPUT < VIntAGDN , the conversion result is 00H (VAINPUT is the analog input voltage). If the external reference voltages VAGND = 0 V and VAREF = +5 V (with respect to VSS and VCC) are applied, then the following internal reference voltages VIntAGND and VIntAREF shown in table 7-7 can be adjusted via the special function register DAPR.
Figure 7-29 Special Function Register DAPR (Address DAH) 0DAH Programming of VIntAREF Programming of VIntAGND DAPR
D/A converter program register. Each 4-bit nibble is used to program the internal reference voltages. Write-access to DAPR starts conversion. DAPR (.3-.0) 16
VIntAGND = VAGND +
(VAREF - VAGND)
with DAPR (.3-.0) < 13;
VIntAGND = VAGND +
DAPR (.7-.4) 16
(VAREF - VAGND)
with DAPR (.7-.4) > 3;
Semiconductor Group
77
On-Chip Peripheral Components
Table 7-7 Adjustable Internal Reference Voltages Step 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 DAPR (.3-.0) DAPR (.7-.4) 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111
VIntAGND
0.0 0.3125 0.625 0.9375 1.25 1.5625 1.875 2.1875 2.5 2.8125 3.125 3.4375 3.75 - - -
VIntAREF
5.0 - - - 1.25 1.5625 1.875 2.1875 2.5 2.8125 3.125 3.4375 3.75 4.0625 4.375 4.68754
The programmability of the internal reference voltages allows adjusting the internal voltage range to the range of the external analog input voltage or it may be used to increase the resolution of the converted analog input voltage by starting a second conversion with a compressed internal reference voltage range close to the previously measured analog value. Figures 7-30 and 7-31 illustrate these applications.
Semiconductor Group
78
On-Chip Peripheral Components
Figure 7-30 Adjusting the Internal Reference Voltages within Range of the External Analog Input Voltages
Figure 7-31 Increasing the Resolution by a Second Conversion
Semiconductor Group
79
On-Chip Peripheral Components
The external reference voltage supply need only be applied when the A/D converter is used, otherwise the pins VAREF and VAGND may be left unconnected. The reference voltage supply has to meet some requirements concerning the level of VAGND and VAREF and the output impedance of the supply voltage (see also "A/D Converter Characteristics" in the data sheet). - The voltage VAREF must meet the following specification: VAREF = VCC 5 % - The voltage VAGND must meet a similar specification: VAGND = VSS 0.2 V - The differential output impedance of the analog reference supply voltage should be less than 1 k lf the above mentioned operating conditions are not met the accuracy of the converter may be decreased. Furthermore, the analog input voltage VAINPUT must not exceed the range from (VAGND - 0.2 V) to (VAREF + 0.2 V). Otherwise, a static input current might result at the corresponding analog input which will also affect the accuracy of the other input channels. 7.4.3 A/D Converter Timing
A conversion is started by writing into special function register DAPR. A write-to-DAPR will start a new conversion even if a conversion is currently in progress. The conversion begins with the next machine cycle and the busy flag BSY will be set. The conversion procedure is divided into three parts: Load time (tL): During this time the analog input capacitance CI (see data sheet) must be loaded to the analog input voltage level. The external analog source needs to be strong enough to source the current to load the analog input capacitance during the load time. This causes some restrictions for the impedance of the analog source. For a typical application the value of the impedance should be less than approx. 5 k. Sample time (tS): During this time the internal capacitor array is connected to the selected analog input channel. The sample time includes the load time which is described above. After the load time has passed the selected analog input must be held constant for the rest of the sample time. Otherwise the internal calibration of the comparator circuitry could be affected which might result in a reduced accuracy of the converter. However, in typical applications a voltage change of approx. 200 - 300 mV at the inputs during this time has no effect.
Semiconductor Group
80
On-Chip Peripheral Components
Conversion time (tC): The conversion time tC includes the sample and load time. Thus, tC is the total time required for one conversion. After the load time and sample time have elapsed, the conversion itself is performed during the rest of tC. In the last machine cycle the converted result is moved to ADDAT; the busy flag (BSY) is cleared before. The A/D converter interrupt is generated by bit IADC in register IRCON. IADC is already set some cycles before the result is written to ADDAT. The flag IADC is set before the result is available in ADDAT because the shortest possible interrupt latency time is taken into account in order to ensure optimal performance. Thus, the converted result appears at the same time in ADDAT when the first instruction of the interrupt service routine is executed. Similar considerations apply to the timing of the flag BSY where usually a "JB BSY,$" instruction is used for polling. lf a continuous conversion is established, the next conversion is automatically started in the machine cycle following the last cycle of the previous conversion.
Figure 7-32 Timing Diagram of an A/D Converter
Semiconductor Group
81
On-Chip Peripheral Components
7.5
Timer 2 with Additional Compare/Capture/Reload
The timer 2 with additional compare/capture/reload features is one of the most powerful peripheral units of the SAB 80(C)515. lt is used for all kinds of digital signal generation and event capturing like pulse generation, pulse width modulation, pulse width measuring etc. This allows various automotive control applications (ignition/injection-control, anti-lock-brake ...) as well as industrial applications (DC-, three-phase AC- and stepper-motor control, frequency generation, digital-to-analog conversion, process control ...). Please note that this timer is not equivalent to timer 2 of the SAB 80(C)52 (see section 7.5.1 ). Timer 2 in combination with the compare/capture/reload registers allows the following modes: Compare: Capture: Reload: up to 4 PWM signals with 65535 steps at maximum, and 1 sec resolution up to 4 high speed inputs with 1 sec resolution modulation of timer 2 cycle time
The block diagram in figure 7-33 a) shows the general configuration of timer 2 with the additional compare/capture/reload registers. The corresponding port functions are listed in table 7-8. Table 7-9 shows the additional special function registers of timer 2.
Semiconductor Group
82
On-Chip Peripheral Components
Figure 7-33 a) Timer 2 Block Diagram Semiconductor Group 83
On-Chip Peripheral Components
Figure 7-33 b) Timer 2 in Reload Mode Table 7-8 Alternate Port Functions of Timer 2 Pin Symbol P1.7/T2 P1.5/T2EX P1.3/INT6/CC3 P1.2/INT5/CC2 P1.1/INT4/CC1 P1.0/INT3/CC0 Input (I) Output (O) I/O I/O I/O I/O I/O I/O Function External count or gate input to timer 2 External reload trigger input Comp. output/capture input for CC register 3 Comp. output/capture input for CC register 2 Comp. output/capture input for CC register 1 Comp. output/capture input for CRC register
Semiconductor Group
84
On-Chip Peripheral Components
Table 7-9 Additional Special Function Registers of Timer 2 Symbol CCEN CCH1 CCH2 CCH3 CCL1 CCL2 CCL3 CRCH CRCL IRCON TH2 TL2 T2CON 7.5.1 Timer 2 Description Comp./capture enable reg. Comp./capture reg. 1, high byte Comp./capture reg. 2, high byte Comp./capture reg. 3, high byte Comp./capture reg. 1, low byte Comp./capture reg. 2, low byte Comp./capture reg. 3, low byte Com./rel./capt. reg., high byte Com./rel./capt. reg., low byte Interrupt control register Timer 2, high byte Timer 2, low byte Timer 2 control register Address 0C1H 0C3H 0C5H 0C7H 0C2H 0C4H 0C6H 0CBH 0CAH 0C0H 0CDH 0CCH 0C8H
The timer 2, which is a 16-bit-wide register, can operate as timer, event counter, or gated timer. Timer Mode In timer function, the count rate is derived from the oscillator frequency. A 2:1 prescaler offers the possibility of selecting a count rate of 1/12 or 1/24 of the oscillator frequency. Thus, the 16-bit timer register (consisting of TH2 and TL2) is either incremented in every machine cycle or in every second machine cycle. The prescaler is selected by bit T2PS in special function register T2CON (see figure 7-35). lf T2PS is cleared, the input frequency is 1/12 of the oscillator frequency; if T2PS is set, the 2:1 prescaler gates 1/24 of the oscillator frequency to the timer. Gated Timer Mode In gated timer function, the external input pin T2 (P1.7) functions as a gate to the input of timer 2. lf T2 is high, the internal clock input is gated to the timer. T2 = 0 stops the counting procedure. This will facilitate pulse width measurements. The external gate signal is sampled once every machine cycle (for the exact port timing, please refer to section 7.1 "Parallel I/O").
Semiconductor Group
85
On-Chip Peripheral Components
Event Counter Mode In the counter function, the timer 2 is incremented in response to a 1-to-0 transition at its corresponding external input pin T2 (P1.7). In this function, the external input is sampled every machine cycle. When the sampled inputs show a high in one cycle and a low in the next cycle, the count is incremented. The new count value appears in the timer register in the cycle following the one in which the transition was detected. Since it takes two machine cycles (24 oscillator periods) to recognize a 1-to-0 transition, the maximum count rate is 1/24 of the oscillator frequency. There are no restrictions on the duty cycle of the external input signal, but to ensure that a given level is sampled at least once before it changes, it must be held for at least one full machine cycle (see also section 7.1 "Parallel I/O" for the exact sample time at the port pin P1.7). Note: The prescaler must be off for proper counter operation of timer 2, i.e. T2PS must be 0. In either case, no matter whether timer 2 is configured as timer, event counter, or gated timer, a rolling-over of the count from all 1's to all 0's sets the timer overflow flag TF2 (bit 6 in SFR IRCON, interrupt request control) which can generate an interrupt. lf TF2 is used to generate a timer overflow interrupt, the request flag must be cleared by the interrupt service routine as it could be necessary to check whether it was the TF2 flag or the external reload request flag EXF2 which requested the interrupt (for EXF2 see below). Both request flags cause the program to branch to the same vector address. The input clock to timer 2 is selected by bits T2I0, T2I1, and T2PS as listed in figure 7-35. Reload of Timer 2 (see figure 7-33 b) ) The reload mode for timer 2 is selected by bits T2R0 and T2R1 in SFR T2CON as listed in figure 7-35. Two reload modes are selectable: In mode 0, when timer 2 rolls over from all 1's to all 0's, it not only sets TF2 but also causes the timer 2 registers to be loaded with the 16-bit value in the CRC register, which is preset by software. The reload will happen in the same machine cycle in which TF2 is set, thus overwriting the count value 0000H. In mode 1, a 16-bit reload from the CRC register is caused by a negative transition at the corresponding input pin T2EX/P1.5. In addition, this transition will set flag EXF2, if bit EXEN2 in SFR IEN1 is set. lf the timer 2 interrupt is enabled, setting EXF2 will generate an interrupt (more about interrupts in section 8). The external input pin T2EX is sampled in every machine cycle. When the sampling shows a high in one cycle and a low in the next cycle, a transition will be recognized. The reload of timer 2 registers will then take place in the cycle following the one in which the transition was detected.
Semiconductor Group
86
On-Chip Peripheral Components
Figure 7-34 Special Function Register T2CON 0CFH 0C8H T2PS 0CEH I3FR 0CDH I2FR 0CCH T2R1 0CBH T2R0 0CAH T2CM 0C9H T2I1 0C8H T2I0 T2CON
These bits are not used in combination with timer 2. Timer 2 control register. Bit-addressable register which controls timer 2 function and compare mode of registers CRC, CC1 to CC3.
Bit T2I1 0 0 1 1 T2R1 0 1 1 T2CM I3FR T2I0 0 1 0 1 T2R0 X 0 1
Symbol Timer 2 input selection No input selected, timer 2 stops Timer function input frequency = fOSC/12 (T2PS = 0) or fOSC/24 (T2PS = 1) Counter function, external input signal at pin T2/P1.7 Gated timer function, input controlled by pin T2/P1.7 Timer 2 reload mode selection Reload disabled Mode 0: auto-reload upon timer 2 overflow (TF2) Mode 1: reload upon falling edge at pin T2EX/P1.5 Compare mode bit for registers CRC, CC1 through CC3. When set, compare mode 1 is selected. T2CM = 0 selects compare mode 0. External interrupt 3 falling/rising edge flag, also used for capture function in combination with register CRC (see section 7.5.3). If set, capture to register to CRC (if enabled) will occur on a positive transition at pin P1.0/INT3/CC0. If I3FR is cleared, capture will occur on a negative transition. Prescaler select bit. When set, timer 2 is clocked in the "timer" or "gated timer" function with 1/24 of the oscillator frequency. T2PS = 0 gates fOSC/12 to timer 2. T2PS must be 0 for the counter operation of timer 2.
T2PS
Semiconductor Group
87
On-Chip Peripheral Components
7.5.2
Compare Function of Registers CRC, CC1 to CC3
The compare function of a timer/register combination can be described as follows. The 16-bit value stored in a compare/capture register is compared with the contents of the timer register. lf the count value in the timer register matches the stored value, an appropriate output signal is generated at a corresponding port pin, and an interrupt is requested. The contents of a compare register can be regarded as 'time stamp' at which a dedicated output reacts in a predefined way (either with a positive or negative transition). Variation of this 'time stamp' somehow changes the wave of a rectangular output signal at a port pin. This may - as a variation of the duty cycle of a periodic signal - be used for pulse width modulation as well as for a continually controlled generation of any kind of square wave forms. In the case of the SAB 80(C)515, two compare modes are implemented to cover a wide range of possible applications. The compare modes 0 and 1 are selected by bit T2CM in special function register T2CON (see figure 7-34). In both compare modes, the new value arrives at the port pin 1 within the same machine cycle in which the internal compare signal is activated. The four registers CRC, CC1 to CC3 are multifunctional as they additionally provide a capture, compare or reload capability (the CRC register only, see section 7.5.1). A general selection of the function is done in register CCEN (see figure 7-40). Please note that the compare interrupt CC0 can be programmed to be negative or positive transition activated. The internal compare signal (not the output signal at the port pin!) is active as long as the timer 2 contents is equal to the one of the appropriate compare registers, and it has a rising and a falling edge. Thus, when using the CRC register, it can be selected whether an interrupt should be caused when the compare signal goes active or inactive, depending on bit I3FR in T2CON. For the CC registers 1 to 3 an interrupt is always requested when the compare signal goes active (see figure 7-36). 7.5.2.1 Compare Mode 0 In mode 0, upon matching the timer and compare register contents, the output signal changes from low to high. lt goes back to a low level on timer overflow. As long as compare mode 0 is enabled, the appropriate output pin is controlled by the timer circuit only, and not by the user. Writing to the port will have no effect. Figure 7-35 shows a functional diagram of a port latch in compare mode 0. The port latch is directly controlled by the two signals timer overflow and compare. The input line from the internal bus and the write-to-latch line are disconnected when compare mode 0 is enabled. Compare mode 0 is ideal for generating pulse width modulated output signals, which in turn can be used for digital-to-analog conversion via a filter network or by the controlled device itself (e.g. the inductance of a DC or AC motor). Mode 0 may also be used for providing output clocks with initially defined period and duty cycle. This is the mode which needs the least CPU time. Once set up, the output goes on oscillating without any CPU intervention. Figure 7-36 and 7-37 illustrate the function of compare mode 0.
Semiconductor Group
88
On-Chip Peripheral Components
Figure 7-35 Port Latch in Compare Mode 0
Figure 7-36 Timer 2 with Registers CCx in Compare Mode 0 (CCx stands for CRC, CC1 to CC3; IEXx stands for IEX3 to IEX6)
Semiconductor Group
89
On-Chip Peripheral Components
Timer Count = FFFF H
Timer Count = Reload Value Interrupt can be generated on overflow
Compare Output (P1.x/CCx)
MCT01906
Figure 7-37 Function of Compare Mode 0 Modulation Range in Compare Mode 0 Generally it can be said that for every PWM generation in compare mode 0 with n-bit wide compare registers there are 2n different settings for the duty cycle. Starting with a constant low level (0% duty cycle) as the first setting, the maximum possible duty cycle then would be (1 - 1/2n) x 100% This means that a variation of the duty cycle from 0% to real 100% can never be reached if the compare register and timer register have the same length. There is always a spike which is as long as the timer clock period. This "spike" may either appear when the compare register is set to the reload value (limiting the lower end of the modulation range) or it may occur at the end of a timer period. In a timer 2/CCx register configuration in compare mode 0 this spike is divided into two halves: one at the beginning when the contents of the compare register is equal to the reload value of the timer; the other half when the compare register is equal to the maximum value of the timer register (here: 0FFFFH). Please refer to figure 7-38 where the maximum and minimum duty cycle of a compare output signal is illustrated. Timer 2 is incremented with the machine clock (fOSC/12), thus at 12-MHz operational frequency, these spikes are both approx. 500 ns long.
Semiconductor Group
~ ~
Contents of Timer 2
~ ~
Timer Count = Compare Value
Interrupt can be generated on compare-match
90
On-Chip Peripheral Components
Figure 7-38 Modulation Range of a PWM Signal, Generated with a Timer 2/CCx Register Combination in Compare Mode 0 The following example shows how to calculate the modulation range for a PWM signal. To calculate with reasonable numbers, a reduction of the resolution to 8-bit is used. Otherwise (for the maximum resolution of 16-bit) the modulation range would be so severely limited that it would be negligible. Example: Timer 2 in auto-reload mode; contents of reload register CRC = 0FF00H Restriction of modulation range = 1 x 100% = 0.195% 256 x 2
This leads to a variation of the duty cycle from 0.195% to 99.805% for a timer 2/CCx register configuration when 8 of 16 bits are used.
Semiconductor Group
91
On-Chip Peripheral Components
7.5.2.2 Compare Mode 1 In compare mode 1, the software adaptively determines the transition of the output signal. lt is commonly used when output signals are not related to a constant signal period (as in a standard PWM generation) but must be controlled very precisely with high resolution and without jitter. In compare mode 1, both transitions of a signal can be controlled. Compare outputs in this mode can be regarded as high speed outputs which are independent of the CPU activity. lf mode 1 is enabled, and the software writes to the appropriate output latch at the port, the new value will not appear at the output pin until the next compare match occurs. Thus, one can choose whether the output signal is to make a new transition (1-to-0 or 0-to-1, depending on the actual pinlevel) or should keep its old value at the time the timer 2 count matches the stored compare value. Figure 7-39 shows a functional diagram of a timer/compare register/port latch configuration in compare mode 1. In this function, the port latch consists of two separate latches. The upper latch (which acts as a "shadow latch") can be written under software control, but its value will only be transferred to the output latch (and thus to the port pin) in response to a compare match. Note that the double latch structure is transparent as long as the internal compare signal is active. While the compare signal is active, a write operation to the port will then change both latches. This may become important when driving timer 2 with a slow external clock. In this case the compare signal could be active for many machine cycles in which the CPU could unintentionally change the contents of the port latch. For details see also section 7.5.2.3 "Using Interrupts in Combination with the Compare Function". A read-modify-write instruction (see section 7.1) will read the user-controlled "shadow latch" and write the modified value back to this "shadow-latch". A standard read instruction will - as usual - read the pin of the corresponding compare output.
Semiconductor Group
92
On-Chip Peripheral Components
Figure 7-39 Timer 2 with Registers CCx in Compare Mode 1 (CCx stands for CRC, CC1 to CC3; IEXx stands for IEX3 to IEX6)
Semiconductor Group
93
On-Chip Peripheral Components
Figure 7-40 Special Function Register CCEN 0C1H COCAH3 COCAL3 COCAH2 COCAI2 COCAH1 COCAL1 COCAH0 COCAL0 CCEN Compare/capture enable register selects compare or capture function for register CRC, CC1 to CC3.
Bit COCAH0 0 0 1 1 COCAH1 0 0 1 1 COCAH2 0 0 1 1 COCAH3 0 0 1 1 COCAL0 0 1 0 1 COCAL1 0 1 0 1 COCAL2 0 1 0 1 COCAL3 0 1 0 1
Function Compare/capture mode for CRC register Compare/capture disabled Capture on falling/rising edge at pin P1.0/INT3/CC0 Compare enabled Capture on write operation into register CRCL Compare/capture mode for CC register 1 Compare/capture disabled Capture on rising edge at pin P1.1/INT4/CC1 Compare enabled Capture on write operation into register CCL1 Compare/capture mode for CC register 2 Compare/capture disabled Capture on rising edge at pin P1.2/INT5/CC2 Compare enabled Capture on write operation into register CCL2 Compare/capture mode for CC register 3 Compare/capture disabled Capture on rising edge at pin P1.3/INT6/CC3 Compare enabled Capture on write operation into register CCL3
7.5.2.3 Using Interrupts in Combination with the Compare Function The compare service of registers CRC, CC1, CC2 and CC3 is assigned to alternate output functions at port pins P1.0 to P1.3. Another option of these pins is that they can be used as external interrupt inputs. However, when using the port lines as compare outputs then the input line from the port pin to the interrupt system is disconnected (but the pin's level can still be read under software control). Thus, a change of the pin's level will not cause a setting of the corresponding interrupt flag. In this case, the interrupt input is directly connected to the (internal) compare signal thus providing a compare interrupt.
Semiconductor Group
94
On-Chip Peripheral Components
The compare interrupt can be used very effectively to change the contents of the compare registers or to determine the level of the port outputs for the next "compare match". The principle is, that the internal compare signal (generated at a match between timer count and register contents) not only manipulates the compare output but also sets the corresponding interrupt request flag. Thus, the current task of the CPU is interrupted - of course provided the priority of the compare interrupt is higher than the present task priority - and the corresponding interrupt service routine is called. This service routine then sets up all the necessary parameters for the next compare event. Some advantages in using compare interrupts: Firstly, there is no danger of unintentional overwriting a compare register before a match has been reached. This could happen when the CPU writes to the compare register without knowing about the actual timer 2 count. Secondly, and this is the most interesting advantage of the compare feature, the output pin is exclusively controlled by hardware therefore completely independent from any service delay which in real time applications could be disastrous. The compare interrupt in turn is not sensitive to such delays since it loads the parameters for the next event. This in turn is supposed to happen after a sufficient space of time. Please note two special cases where a program using compare interrupts could show a "surprising" behavior: The first configuration has already been mentioned in the description of compare mode 1. The fact that the compare interrupts are transition activated becomes important when driving timer 2 with a slow external clock. In this case it should be carefully considered that the compare signal is active as long as the timer 2 count is equal to the contents of the corresponding compare register, and that the compare signal has a rising and a falling edge. Furthermore, the "shadow latches" used in compare mode 1 are transparent while the compare signal is active. Thus, with a slow input clock for timer 2, the comparator signal is active for a long time (= high number of machine cycles) and therefore a fast interrupt controlled reload of the compare register could not only change the "shadow latch" - as probably intended - but also the output buffer. When using the CRC , you can select whether an interrupt should be generated when the compare signal goes active or inactive, depending on the status of bit I3FR in T2CON (see figure 8-5). Initializing the interrupt to be negative transition triggered is advisive in the above case. Then the compare signal is already inactive and any write access to the port latch just changes the contents of the "shadow-latch". Please note that for CC registers 1 to 3 an interrupt is always requested when the compare signal goes active.
Semiconductor Group
95
On-Chip Peripheral Components
The second configuration which should be noted is when compare function is combined with negative transition activated interrupts. lf the port latch of port P1.0 contains a 1, the interrupt request flags IEX2 will immediately be set after enabling the compare mode for the CRC register. The reason is that first the external interrupt input is controlled by the pin's level. When the compare option is enabled the interrupt logic input is switched to the internal compare signal, which carries a low level when no true comparison is detected. So the interrupt logic sees a 1-to-0 edge and sets the interrupt request flag. An unintentional generation of an interrupt during compare initialization can be prevented if the request flag is cleared by software after the compare is activated and before the external interrupt is enabled. 7.5.3 Capture Function
Each of the three compare/capture registers CC1 to CC3 and the CRC register can be used to latch the current 16-bit value of the timer 2 registers TL2 and TH2. Two different modes are provided for this function. In mode 0, an external event latches the timer 2 contents to a dedicated capture register. In mode 1, a capture will occur upon writing to the low order byte of the dedicated 16-bit capture register. This mode is provided to allow the software to read the timer 2 contents "on-thefly". In mode 0, the external event causing a capture is - for CC registers 1 to 3: a positive transition at pins CC1 to CC3 of port 1 - for the CRC register: a positive or negative transition at the corresponding pin, depending on the status of the bit I3FR in SFR T2CON. lf the edge flag is cleared, a capture occurs in response to a negative transition; if the edge flag is set a capture occurs in response to a positive transition at pin P1.0/INT3/ CC0. In both cases the appropriate port 1 pin is used as input and the port latch must be programmed to contain a one (1). The external input is sampled in every machine cycle. When the sampled input shows a low (high) level in one cycle and a high (low) in the next cycle, a transition is recognized. The timer 2 contents is latched to the appropriate capture register in the cycle following the one in which the transition was identified. In mode 0 a transition at the external capture inputs of registers CC0 to CC3 will also set the corresponding external interrupt request flags IEX3 to IEX6. lf the interrupts are enabled, an external capture signal will cause the CPU to vector to the appropriate interrupt service routine. In mode 1 a capture occurs in response to a write instruction to the low order byte of a capture register. The write-to-register signal (e.g. write-to-CRCL) is used to initiate a capture. The value written to the dedicated capture register is irrelevant for this function. The timer 2 contents will be latched into the appropriate capture register in the cycle following the write instruction. In this mode no interrupt request will be generated.
Semiconductor Group
96
On-Chip Peripheral Components
Figures 7-41 and 7-42 show functional diagrams of the capture function of timer 2. Figure 7-41 illustrates the operation of the CRC register, while figure 7-42 shows the operation of the compare/ capture registers 1 to 3. The two capture modes can be established individually for each capture register by bits in SFR CCEN (compare/capture enable register). That means, in contrast to the compare modes, it is possible to simultaneously select mode 0 for one capture register and mode 1 for another register. The bit positions and functions of CCEN are listed in figure 7-40.
Figure 7-41 Capture with Register CRC
Semiconductor Group
97
On-Chip Peripheral Components
Figure 7-42 Capture with Registers CC1 to CC3 7.6 Power Saving Modes
For significantly reducing power consumption, the SAB 80(C)515/80(C)535 provides two Power Saving Modes: - The Power-Down Mode Operation of the component stops completely, the oscillator is turned off. Only the internal RAM is supplied with a very low standby current. - The Idle Mode (SAB 80C515/80C535 only) The CPU is gated off from the oscillator. All peripherals are further supplied by the oscillator clock and are able to do their jobs. These modes are described separatly for each component in the following sections. There are numerous applications which require high system security and at the same time reliability in electrically noisy environments. In such applications unintentional entering of the power saving modes must be absolutely avoided. A power saving mode would reduce the controller's perfomance (in case of idle mode) or even stop each operation (in case of power-down mode). This situation might be fatal for the system. Such critical applications often use the watchdog timer to prevent the system from program upsets. Then accidental entering of the power saving modes would even stop the watchdog timer and would circumvent the task of system reliability. The SAB 80C515/80C535 provides software and hardware protection against accidental entering as described above (see chapter 7.6.2).
Semiconductor Group
98
On-Chip Peripheral Components
7.6.1
Power Saving Modes of the SAB 80515/80535
The SAB 80515/80535 allows a reduction of the power consumption using the power-down mode. 7.6.1.1 Power-Down Mode of the SAB 80515/80535 The power-down mode in the SAB 80515/80535 allows a reduction of VCC , to zero while saving 40 bytes of the on-chip RAM through a backup supply connected to the VPD pin. In the following, the terms VCC and VPD are used to specify the voltages on pin VCC and pin VPD, respectively. lf VCC > VPD , the 40 bytes are supplied from VCC . VPD may then below. lf VCC < VPD , the current for the 40 bytes is drawn from VPD . The addresses of these backup-powered RAM locations range from 88 to 127 (58H to 7FH). The current drawn from the backup power supply is typically 1 mA, max. 3 mA. To utilize this feature, the user's system - upon detecting an imminent power failure - would interrupt the processor in some manner to transfer relevant data to the 40-byte on-chip RAM and enable the backup power supply to the VPD pin. Then a reset should be accomplished before VCC falls below its operating limit. When power returns, a power-on reset should be accomplished, and the backup supply needs to stay on long enough to resume normal operation. Figure 7-43 illustrates the timing upon a power failure.
Figure 7-43 Reset and RAM Backup Power Timing of the SAB 80515/80535
Semiconductor Group
99
On-Chip Peripheral Components
7.6.2
Power Saving Modes of the SAB 80515/80535
Dlfferences between the Power-Down Modes of the SAB 80C515/80C535 and the SAB 80515/ 80535 The power-down mode of the SAB 80515/80535 allows retention of 40 bytes on-chip RAM through a backup supply connected to the VPD pin. The ACMOS versions SAB 80C515/80C535 have the following additional features: - The same power supply (pin VCC) for active, power-down (retention of the whole int. RAM area), and idle mode. - An extra pin (PE) that allows enabling/disabling of the power-saving modes. - A software protection that enables the power saving modes via special function register PCON (Power Control Register). Hardware Enable for the Use of the Power Saving Modes To provide power saving modes together with effective protection against unintentional entering of these modes, the SAB 80C515/80C535 has an extra pin for disabling the use of the power saving modes. This pin is called PE (power saving enable), and its function is as follows: PE = 1 (logic high level): Use of the power saving modes is not possible. The instruction sequences used for entering these modes will not affect the normal operation of the device. PE = 0 (logic low level): All power saving modes can be activated as described in the following sections.
When left unconnected, the pin PE is pulled to high level by a weak internal pullup. This is done to provide system protection by default. In addition to the hardware enable/disable of the power saving modes, a double-instruction sequence which is described in the corresponding sections is necessary to enter power-down and idle mode. The combination of all these safety precautions provides a maximum of system protection. Application Example for Switching Pin PE For most applications in noisy environments, certain components external to the chip are used to give warning of a power failure or a turn off of the power supply. These circuits could be used to control the PE pin. The possible steps to go into power-down mode could then be as follows: - A power-fail signal forces the controller to go into a high priority interrupt routine. This interrupt routine saves the actual program status. At the same time pin PE is pulled low by the powerfail signal. - Finally the controller enters power-down mode by executing the relevant double-instruction sequence.
Semiconductor Group
100
On-Chip Peripheral Components
7.6.2.1 Power-Down Mode of the SAB 80C515/80C535 In the power-down mode, the on-chip oscillator is stopped. Therefore, all functions are stopped, only the contents of the on-chip RAM and the SFR's are held. The port pins controlled by their port latches output the values that are held by their SFR'S. The port pins which serve the alternate output functions show the values they had at the end of the last cycle of the instruction which initiated the power-down mode; when enabled, the clockout signal (P1.6/CLKOUT) will stop at low level. ALE and PSEN are held at logic low level (see table 7-10). lf the power-down mode is to be used, the pin PE must be held low. Entering the power-down mode is done by two consecutive instructions immediately following each other. The first instruction has to set the flag bit PDE (PCON.1) and must not set bit PDS (PCON.6). The following instruction has to set the start bit PDS (PCON.6) and must not set bit PDE (PCON.1). The hardware ensures that a concurrent setting of both bits, PDE and PDS, will not initiate the power-down mode. Bit PDE and PDS will automatically be cleared after having been set and the value shown when reading one of these bits is always zero (0). Figure 7-44 shows the special function register PCON. This doubleinstruction sequence is implemented to minimize the chance of unintentionall entering the powerdown mode, which could possibly "freeze" the chip's activity in an undesired status. Note that PCON is not a bit-addressable register, so the above mentioned sequence for entering the power-down mode is composed of byte handling instructions. The following instruction sequence may serve as an example: ORL ORL PCON,#00000010B PCON,#01000000B ;Set bit PDE, ;bit PDS must not be set ;Set bit PDS, ;bit PDE must not be set
The instruction that sets bit PDS is the last instruction executed before going into power-down mode. lf idle mode and power-down mode are invoked simultaneously, the power-down mode takes precedence. The only exit from power-down mode is a hardware reset. Reset will redefine all SFR'S, but will not change the contents of the internal RAM. In the power-down mode, VCC can be reduced to minimize power consumption. Care must be taken, however, to ensure that VCC is not reduced before the power-down mode is invoked, and that VCC is restored to its normal operating level before the power-down mode is terminated. The reset signal that terminates the power-down mode also frees the oscillator. The reset should not be activated before VCC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize (similar to power-on reset).
Semiconductor Group
101
On-Chip Peripheral Components
7.6.2.2 Idle Mode of the SAB 80C515/80C535 In idle mode the oscillator of the SAB 80C515/80C535 continues to run, but the CPU is gated off from the clock signal. However, the interrupt system, the serial channel, the A/D converter and all timers, except for the watchdog timer, are further provided with the clock. The CPU status is preserved in its entirety: the stack pointer, program counter, program status word, accumulator, and all other registers maintain their data during idle mode. The reduction of power consumption, which can be achieved by this feature, depends on the number of peripherals running. lf all timers are stopped and the A/D converter and the serial interface are not running, maximum power reduction can be achieved. This state is also the test condition for the idle ICC (see the DC characteristics in the data sheet). Thus, the user has to make sure that the right peripheral continues to run or is stopped, respectively, during idle. Also, the state of all port pins - either the pins controlled by their latches or controlled by their secondary functions - depends on the status of the controller when entering idle. Normally the port pins hold the logical state they had at the time idle was activated. lf some pins are programmed to serve their alternate functions they still continue to output during idle if the assigned function is on. This applies for the compare outputs as well as for the system clock output signal and the serial interface in case the latter could not finish reception or transmission during normal operation. The control signals ALE and PSEN are held at logic high levels (see table 7-10). During idle, as in normal operating mode, the ports can be used as inputs. Thus, a capture or reload operation as well as an A/D conversion can be triggered, the timers can be used to count external events and external interrupts can be detected.
Semiconductor Group
102
On-Chip Peripheral Components
Table 7-10 Status of External Pins During Idle and Power-Down Mode Outputs Idle ALE PSEN Port 0 Port 1 Port 2 Port 3 Port 4 Port 5 High High Data Data/alternate outputs Data Data/alternate outputs Data Data Last Instruction Executed from Internal Code Memory Power-down Low Low Data Data/ last output Data Data/ last output Data Data Idle High High Float Data/alternate outputs Address Data/alternate outputs Data Data Last Instruction Executed from External Code Memory Power-down Low Low Float Data/ last output Data Data/ last output Data Data
The watchdog timer is the only peripheral which is automatically stopped during idle. The idle mode makes it possible to "freeze" the processor's status for a certain time or until an external event causes the controller to go back into normal operating mode. Since the watchdog timer is stopped during idle mode, this useful feature of the SAB 80C515/80C535 is provided even if the watchdog function is used simultaneously. lf the idle mode is to be used the pin PE must be held low. Entering the idle mode is to be done by two consecutive instructions immediately following each other. The first instruction has to set the flag bit IDLE (PCON.0) and must not set bit IDLS (PCON.5), the following instruction has to set the start bit IDLS (PCON.5) and must not set bit IDLE (PCON.0). The hardware ensures that a concurrent setting of both bits, IDLE and IDLS will not initiate the idle mode. Bits IDLE and IDLS will automatically be cleared after having been set. lt one of these register bits is read the value shown is zero (0). Figure 7-44 shows special function register PCON. This double-instruction sequence is implemented to minimize the chance of unintentionally entering the idle mode. Note that PCON is not a bit-addressable register, so the above mentioned sequence for entering the idle mode is to be done by byte handling instructions.
Semiconductor Group
103
On-Chip Peripheral Components
The following instruction sequence may serve as an exemple: ORL ORL PCON,#00000001B PCON,#00100000B ;Set bit IDLE, ;bit IDLS must not be set ;Set bit IDLS, ;bit IDLE must not be set
The instruction that sets bit IDLS is the last instruction executed before going into idle mode. Terminating the Idle Mode - The idle mode can be terminated by activation of any enabled interrupt. The CPU operation is resumed, the interrupt will be serviced and the next instruction to be executed after the RETI instruction will be the one following the instruction that set the bit IDLS. - The other possibility of terminating the idle mode is a hardware reset. Since the oscillator is still running, the hardware reset is held active for only two machine cycles for a complete reset.
Figure 7-44 Special Function Register PCON (Address 87H) of the SAB 80C515/80C535 87H SMOD PDS IDLS - GF1 GF0 PDE IDLE PCON
These bits are not used in controlling the power saving modes.
Bit PDS IDLS GF1 GF0 PDE IDLE
Function Power-down start bit. The instruction that sets the PDS flag bit is the last instruction before entering the power-down mode. IDLE start bit. The instruction that sets the IDSL flag bit is the last instruction before entering the idle mode. General purpose flag General purpose flag Power-down enable bit. When set, starting the power-down mode is enabled. Idle mode enable bit. When set, starting the idle mode is enabled.
Semiconductor Group
104
On-Chip Peripheral Components
7.7
Watchdog Timer
As a means of graceful recovery from software or hardware upset a watchdog timer is provided in the SAB 80(C)515/80(C)535. lf the software fails to clear the watchdog timer at least every 65532 s, an internal hardware reset will be initiated. The software can be designed such that the watchdog times out if the program does not progress properly. The watchdog will also time out if the software error was due to hardware-related problems. This prevents the controller from malfunctioning for longer than 65 ms if a 12-MHz oscillator is used. The watchdog timer is a 16-bit counter which is incremented once every machine cycle. After an external reset the watchdog timer is disabled and cleared to 0000H. The counter is started by setting bit SWDT (bit 6 in SFR IEN1). After having been started, the bit WDTS (watchdog timer status, bit 6 in SFR IP0) is set. Note that the watchdog timer cannot be stopped by software. lt can only be cleared to 0000H by first setting bit WDT (IEN0.6) and with the next instruction setting SWDT. Bit WDT will automatically be cleared during the second machine cycle after having been set. For this reason, setting SWDT bit has to be a one cycle instruction (e.g. SETB SWDT). This double instruction clearing of the watchdog timer was implemented to minimize the chance of unintentionally clearing the watchdog. To prevent the watchdog from overflowing, it must be cleared periodically. Starting the watchdog timer by setting only bit SWDT does not reload the WDTREL register to the watchdog timer registers WDTL/WDTH. A reload occurs only by using the double instruction refresh sequence SETB WDT / SETB SWDT. lf the software fails to clear the watchdog in time, an internally generated watchdog reset is entered at the counter state FFFCH, which lasts four machine cycles. This internal reset differs from an external reset only to the extent that the watchdog timer is not disabled. Bit WDTS (was set by starting WDT) allows the software to examine from which source the reset was initiated. lf it is set, the reset was caused by a watchdog timer overflow.
Figure 7-45 Special Function Register IEN0 0AFH 0A8H EAL 0AEH WDT 0ADH ET2 0ACH ES 0ABH ET1 0AAH EX1 0A9H ET0 0A8H EX0 IEN0
These bits are not used by the watchdog timer.
Bit WDT
Function Watchdog timer refresh flag. Set to initiate a refresh of the watchdog timer. Must be set directly before SWDT is set to prevent an unintentional refresh of the watchdog timer. WDT is reset by hardware two processor cycles after it has been set.
Semiconductor Group
105
On-Chip Peripheral Components
Figure 7-46 Special Function Register IEN1 0BFH 0BEH 0BDH EX6 0BCH EX5 0BBH EX4 0BAH EX3 0B9H EX2 0B8H EADC IEN1
0B8H EXEN2 SWDT
These bits are not used by the watchdog timer.
Bit SWDT
Function Watchdog timer start/refresh flag. Set to activate/refresh the watchdog timer. When directly set after setting WDT, a watchdog timer refresh is performed. Bit SWDT is reset by hardware two processor cycles after it has been set.
Figure 7-47 Special Function Register IP0 0A9H - WDTS IP0.5 IP0.4 IP0.3 IP0.2 IP0.1 IP0.0 IP0
These bits are not used by the watchdog timer.
Bit WDTS
Function Watchdog timer status flag. Set by hardware when the watchdog timer was started. Can be read by software.
Semiconductor Group
106
On-Chip Peripheral Components
7.8
Oscillator and Clock Circuit
XTAL1 and XTAL2 are the input and output of a single-stage on-chip inverter which can be configured with off-chip components as a Pierce oscillator. The oscillator, in any case, drives the internal clock generator. The clock generator provides the internal clock signals to the chip at half the oscillator frequency. These signals define the internal phases, states and machine cycles, as described in chapter 3. 7.8.1 Crystal Oscillator Mode
Figure 7-48 shows the recommended oscillator circuit.
Figure 7-48 Recommended Oscillator Circuit for the SAB 80(C)515/80(C)535 In this application the on-chip oscillator is used as a crystal-controlled, positive-reactance oscillator (a more detailed schematic is given in figure 7-49 and 7-51). lt is operated in its fundamental response mode as an inductive reactor in parallel resonance with a capacitor external to the chip. The crystal specifications and capacitances are non-critical. In this circuit 30 pF can be used as single capacitance at any frequency together with a good quality crystal. A ceramic resonator can be used in place of the crystal in cost-critical applications. lf a ceramic resonator is used, C1 and C2 are normally selected to be different values. We recommend consulting the manufacturer of the ceramic resonator for value specifications of these capacitors. 7.8.2 Driving for External Source
The SAB 80(C)515/80(C)535 can be driven from an external oscillator. Please note that there is a difference between driving MYMOS and ACMOS devices from an external clock source.
Semiconductor Group
107
On-Chip Peripheral Components
7.8.2.1 Driving the SAB 80515/80535 from External Source For driving the SAB 80515/80535 from an external clock source, the external clock signal is to be applied to XTAL2. A pullup resistor is recommended to increase the noise margin, but is optional if the output high level of the driving gate meets the VIH1 specification of XTAL2. XTAL1 has to be connected to ground (see figure 7-50).
Figure 7-49 On-Chip Oscillator Circuitry
Figure 7-50 External Clock Source
Semiconductor Group
108
On-Chip Peripheral Components
7.8.2.2 Driving the SAB 80C515/80C535 from External Source For driving the SAB 80C515/80C535 from an external clock source, the external clock signal is to be applied to XTAL2, as shown in figure 7-52. A pullup resistor is recommended, but is optional if the output high level of the driving gate corresponds to the VIH1 specification of XTAL2. XTAL1 has to be left unconnected.
Figure 7-51 On-Chip Oscillator Circuitry
Figure 7-52 External Clock Source
Semiconductor Group
109
On-Chip Peripheral Components
7.9
System Clock Output
For peripheral devices requiring a system clock, the SAB 80(C)515/80(C)535 provides a clock output signal derived from the oscillator frequency as an alternate output function on pin P1.6/ CLKOUT. lf bit CLK is set (bit 6 of special function register ADCON, see figure 7-53), a clock signal with 1/12 of the oscillator frequency is gated to pin P1.6/CLKOUT. To use this function the port pin must be programmed to a one (1), which is also the default after reset.
Figure 7-53 Special Function Register ADCON (Address 0D8H) 0DFH 0D8H BD 0DEH CLK 0DDH - 0DCH BSY 0DBH ADM 0DAH MX2 0D9H MX1 0D8H MX0 ADCON
These bits are not used in controlling the clock out functions.
Bit CLK
Function Clockout enable bit. When set, pin P1.6/CLKOUT outputs the system clock which is 1/12 of the oscillator frequency.
The system clock is high during S3P1 and S3P2 of every machine cycle and low during all other states. Thus, the duty cycle of the clock signal is 1:6. Associated with a MOVX instruction the system clock coincides with the last state (S3) in which a RD or WR signal is active. A timing diagram of the system clock output is shown in figure 7-54.
Semiconductor Group
110
On-Chip Peripheral Components
Figure 7-54 Timing Diagram - System Clock Output
Semiconductor Group
111
Interrupt System
8
Interrupt System
The SAB 80C515/80C535 provides 12 interrupt sources with four priority levels. Five interrupts can be generated by the on-chip peripherals (i.e. timer 0, timer 1, timer 2, compare timer, serial interface and A/D converter), and seven interrupts may be triggered externally (see figure 8.1). 8.1 Interrupt Structure
A common mechanism is used to generate the various interrupts, each source having its own request flag(s) located in a special function register (e.g. TCON, IRCON, SCON). Provided that the peripheral or external source meets the condition for an interrupt, the dedicated request flag is set, whether an interrupt is enabled or not. For example, each timer 0 overflow sets the corresponding request flag TF0. lf it is already set, it retains a one (1). But the interrupt is not necessarily serviced. Now each interrupt requested by the corresponding flag can individually be enabled or disabled by the enable bits in SFR's IEN0, IEN1 (see figure 8-2, 8-3). This determines whether the interrupt will actually be performed. In addition, there is a global enable bit for all interrupts which, when cleared, disables all interrupts independent of their individual enable bits.
Semiconductor Group
112
Interrupt System
Figure 8-1 a) Interrupt Structure of the SAB 80(C)515/80(C)535 Semiconductor Group 113
Interrupt System
Figure 8-1 b) Interrupt Structure of the SAB 80(C)515/80(C)535 (cont'd)
Semiconductor Group
114
Interrupt System
Figure 8-2 Special Function Register IEN0 (Address 0A8H) 0AFH 0A8H EAL 0AEH WDT 0ADH ET2 0ACH ES 0ABH ET1 0AAH EX1 0A9H ET0 0A8H EX0 IEN0
This bit is not used for interrupt control.
Bit EX0 ET0 EX1 ET1 ES ET2 EAL
Function Enables or disables external interrupt 0. If EX0 = 0, external interrupt 0 is disabled. Enables or disables the timer 0 overflow interrupt. If ET0 = 0, the timer 0 interrupt is disabled. Enables or disables external interrupt 1. If EX1 = 0, external interrupt 1 is disabled. Enables or disables the timer 1 overflow interrupt. If ET1 = 0, the timer 1 interrupt is disabled. Enables or disables the serial channel interrupt. If ES = 0, the serial channel interrupt is disabled. Enables or disables the timer 2 overflow or external reload interrupt. If ET2 = 0, the timer 2 interrupt is disabled. Enables or disables all interrupts. If EAL = 0, no interrupt will be acknowledged. If EAL = 1, each interrupt source is individually enabled or disabled by setting or clearing its enable bit.
Semiconductor Group
115
Interrupt System
Figure 8-3 Special Function Register IEN1 (Address 0B8H) 0BFH 0BEH 0BDH EX6 0BCH EX5 0BBH EX4 0BAH EX3 0B9H EX2 0B8H EADC IEN1
0B8H EXEN2 SWDT
This bit is not used for interrupt control.
Bit EADC EX2 EX3 EX4 EX5 EX6 EXEN2
Function Enables or disables the A/D converter interrupt. If EADC = 0, the A/D converter interrupt is disabled. Enables or disables external interrupt 2/capture/compare interrupt 4. If EX2 = 0, external interrupt 2 is disabled. Enables or disables external interrupt 3/capture/compare interrupt 0. If EX3 = 0, external interrupt 3 is disabled. Enables or disables external interrupt 4/capture/compare interrupt 0. If EX4 = 0, external interrupt 4 is disabled. Enables or disables external interrupt 5/capture/compare interrupt 0. If EX5 = 0, external interrupt 5 is disabled. Enables or disables external interrupt 6/capture/compare interrupt 0 If EX6 = 0, external interrupt 6 is disabled. Enables or disables the timer 2 external reload interrupt. EXEN2 = 0 disables the timer 2 external reload interrupt. The external reload function is not affected by EXEN2.
In the following the interrupt sources are discussed individually. The external interrupts 0 and 1 (INT0 and INT1) can each be either level-activated or negative transition-activated, depending on bits IT0 and IT1 in register TCON (see figure 8-4). The flags that actually generate these interrupts are bits IE0 and lE1 in TCON. When an external interrupt is generated, the flag that generated this interrupt is cleared by the hardware when the service routine is vectored too, but only if the interrupt was transition-activated. lf the interrupt was level-activated, then the requesting external source directly controls the request flag, rather than the on-chip hardware. The timer 0 and timer 1 interrupts are generated by TF0 and TF1 in register TCON, which are set by a rollover in their respective timer/counter registers (exception see section 7.3.4 for timer 0 in mode 3). When a timer interrupt is generated, the flag that generated it is cleared by the on-chip hardware when the service routine is vectored too.
Semiconductor Group
116
Interrupt System
The serial port interrupt is generated by a logical OR of flag RI and Tl in SFR SCON (see figure 7-7). Neither of these flags is cleared by hardware when the service routine is vectored too. In fact, the service routine will normally have to determine whether it was the receive interrupt flag or the transmission interrupt flag that generated the interrupt, and the bit will have to be cleared by software. The timer 2 interrupt is generated by the logical OR of bit TF2 in register T2CON and bit EXF2 in register IRCON. Figures 8-5 and 8-6 show SFR's T2CON and IRCON. Neither of these flags is cleared by hardware when the service routine is vectored to. In fact, the service routine may have to determine whether it was TF2 or EXF2 that generated the interrupt, and the bit will have to be cleared by software.
Figure 8-4 Special Function Register TCON (Address 88H) 8FH 88H TF1 8EH TR1 C5H TF0 8CH TR0 8BH IE1 8AH IT1 89H IE0 88H IT0 TCON
These bits are not used for interrupt control.
Bit IT0 IE0 IT1 IE1 TF0 TF1
Function Interrupt 0 type control bit. Set/cleared by software to specify falling edge/lowlevel triggered external interrupts. Interrupt 0 edge flag. Set by hardware when external interrupt edge is detected. Cleared when interrupt processed. Interrupt 1 type control bit. Set/cleared by software to specify falling edge/lowlevel triggered external interrupts. Interrupt 1 edge flag. Set by hardware when external interrupt edge is detected. Cleared when interrupt processed. Timer 0 overflow flag. Set by hardware on timer/counter overflow. Cleared by hardware when processor vectors to interrupt routine. Timer 1 overflow flag. Set by hardware on timer/counter overflow. Cleared by hardware when processor vectors to interrupt routine.
The A/D converter interrupt is generated by IADC in register IRCON (see figure 8-6). lt is set some cycles before the result is available. That is, if an interrupt is generated, in any case the converted result in ADDAT is valid on the first instruction of the interrupt service routine (with respect to the minimal interrupt response time). lf continuous conversions are established, IADC is set once during each conversion. lf an A/D converter interrupt is generated, flag IADC will have to be cleared by software.
Semiconductor Group
117
Interrupt System
The external interrupt 2 (INT2/) can be either positive or negative transition-activated depending on bit I2FR in register T2CON (see figure 8-5). The flag that actually generates this interrupt is bit IEX2 in register IRCON. lf an interrupt 2 is generated, flag IEX2 is cleared by hardware when the service routine is vectored too.
Figure 8-5 Special Function Register T2CON (Address 0C8H) 0CFH 0C8H T2PS 0CEH I3FR 0CDH I2FR 0CCH T2R1 0CBH T2R0 0CAH T2CM 0C9H T2I1 0C8H T2I0 T2CON
These bits are not used for interrupt control.
Bit I2FR
Function External interrupt 2 falling/rising edge flag. When set, the interrupt 2 request flag IEX2 will be set on a positive transition at pin P1.4/INT2. I2FR = 0 specifies external interrupt 2 to be negative-transition activated. External interrupt 3 falling/rising edge flag. When set, the interrupt 3 request flag IEX3 will be set on a positive transition at pin P1.0/INT3. I3FR = 0 specifies external interrupt 3 to be negative-transition active.
I3FR
Like the external interrupt 2, the external interrupt 3 (INT3) can be either positive or negative transition-activated, depending on bit I3FR in register T2CON. The flag that actually generates this interrupt is bit IEX3 in register IRCON. In addition, this flag will be set if a compare event occurs at pin P1.0/INT3/CC0, regardless of the compare mode established and the transition at the respective pin. The flag IEX3 is cleared by hardware when the service routine is vectored too. The external interrupts 4 (INT4), 5 (INT5), 6 (INT6) are positive transition-activated. The flags that actually generate these interrupts are bits IEX4, IEX5, and IEX6 in register IRCON (see figure 8-6). In addition, these flags will be set if a compare event occurs at the corresponding output pin P1.1/ INT4/CC1, P1.2/INT5/CC2, and P1.3/INT6/CC3, regardless of the compare mode established and the transition at the respective pin. When an interrupt is generated, the flag that generated it is cleared by the on-chip hardware when the service routine is vectored too.
Semiconductor Group
118
Interrupt System
Figure 8-6 Special Function Register IRCON (Address 0C0H) 0C7H 0C0H EXF2 0C6H TF2 0C5H IEX6 0C4H IEX5 0C3H IEX4 0C2H IEX3 0C1H IEX2 0C0H IADC IRCON
Bit IADC IEX2
Function A/D converter interrupt request flag. Set by hardware at the end of a conversion. Must be cleared by software. External interrupt 2 edge flag. Set by hardware when external interrupt edge was detected or when a compare event occurred at pin 1.4/INT2/CC4. Cleared when interrupt processed. External interrupt 3 edge flag. Set by hardware when external interrupt edge was detected or when a compare event occurred at pin 1.0/INT3/CC0. Cleared when interrupt processed. External interrupt 4 edge flag. Set by hardware when external interrupt edge was detected or when a compare event occurred at pin 1.1/INT4/CC1. Cleared when interrupt processed. External interrupt 5 edge flag. Set by hardware when external interrupt edge was detected or when a compare event occurred at pin 1.2/INT5/CC2. Cleared when interrupt processed. External interrupt 6 edge flag. Set by hardware when external interrupt edge was detected or when a compare event occurred at pin 1.3/INT6/CC3. Cleared when interrupt processed. Timer 2 overflow flag. Set by timer 2 overflow. Must be cleared by software. If the timer 2 interrupt is enabled, TF2 = 1 will cause an interrupt. Timer 2 external reload flag. Set when a reload is caused by a negative transition on pin T2EX while EXEN2 = 1. When the timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector the timer 2 interrupt routine. Can be used as an additional external interrupt when the reload function is not used. EXF2 must be cleared by software.
IEX3
IEX4
IEX5
IEX6
TF2 EXF2
Semiconductor Group
119
Interrupt System
All of these bits that generate interrupts can be set or cleared by software, with the same result as if they had been set or cleared by hardware. That is, interrupts can be generated or pending interrupts can be cancelled by software. The only exceptions are the request flags IE0 and lE1. lf the external interrupts 0 and 1 are programmed to be level-activated, IE0 and lE1 are controlled by the external source via pin INT0 and INT1, respectively. Thus, writing a one to these bits will not set the request flag IE0 and/or lE1. In this mode, interrupts 0 and 1 can only be generated by software and by writing a 0 to the corresponding pins INT0(P3.2) and INT1(P3.3), provided that this will not affect any peripheral circuit connected to the pins. Each of these interrupt sources can be individually enabled or disabled by setting or clearing a bit in the special function registers IEN0 and IEN1 (figures 8-2 and 8-3). Note that IEN0 contains also a global disable bit, EAL, which disables all interrupts at once. Also note that in the SAB 8051 the interrupt priority register IP is located at address 0B8H; in the SAB 80(C)515/80(C)535 this location is occupied by register IEN1. 8.2 Priority Level Structure
As already mentioned above, all interrupt sources are combined as pairs; table 8-1 lists the structure of the interrupt sources.
Table 8-1 Pairs of Interrupt Sources External Interrupt 0 Timer 0 interrupt External interrupt 1 Timer 1 interrupt Serial channel 0 interrupt Timer 2 interrupt A/D Converter Interrupt External interrupt 2 External interrupt 3 External interrupt 4 External interrupt 5 External interrupt 6
Each pair of interrupt sources can be programmed individually to one of four priority levels by setting or clearing one bit in the special function register IP0 and one in IP1 (figure 8-7). A low-priority interrupt can be interrupted by a high-priority interrupt, but not by another interrupt of the same or a lower priority. An interrupt of the highest priority level cannot be interrupted by another interrupt source.
Semiconductor Group
120
Interrupt System
lf two or more requests of different priority levels are received simultaneously, the request of the highest priority is serviced first. lf requests of the same priority level are received simultaneously, an internal polling sequence determines which request is to be serviced first. Thus, within each priority level there is a second priority structure determined by the polling sequence, as follows (see figure 8-8): - Within one pair the "left" interrupt is serviced first - The pairs are serviced from top to bottom of the table.
Figure 8-7 Special Function Registers IP0 and IP1 (Address 0A9H and 0B9H) 0A9H 0B9H - - WDTS - IP0.5 IP1.5 IP0.4 IP1.4 IP0.3 IP1.3 IP0.2 IP1.2 IP0.1 IP1.1 IP0.0 IP1.0 IP0 IP1
These bits are not used for interrupt control. Corresponding bit locations in both registers are used to set the interrupt priority level of an interrupt pair. Bit IP1.x 0 0 1 1 Bit IP1.0/IP0.0 IP1.1/IP0.1 IP1.2/IP0.2 IP1.3/IP0.3 IP1.4/IP0.4 IP1.5/IP0.5 0 1 0 1 Function IP0.x - Set priority level 0 (lowest) Set priority level 1 Set priority level 2 Set priority level 3 (highest) Function IE0/IADC TF0/IEX2 IE1/IEX3 TF1/IEX4 RI + TI/IEX5 TF2 + EXF2/IEX6
Semiconductor Group
121
Interrupt System
Figure 8-8 Priority-Within-Level Structure High IE0 TF0 IE1 TF1 RI + TI TF2 + EXF2 Note: This "priority-within-level" structure is only used to resolve simultaneous requests of the same priority level. 8.3 How Interrupts are Handled Interrupt source IADC IEX2 IEX3 IEX4 IEX5 IEX6 High Low Priority
Low
The interrupt flags are sampled at S5P2 in each machine cycle. The sampled flags are polled during the following machine cycle. lf one of the flags was in a set condition at S5P2 of the preceding cycle, the polling cycle will find it and the interrupt system will generate a LCALL to the appropriate service routine, provided this hardware-generated LCALL is not blocked by any of the following conditions: 1) 2) 3) An interrupt of equal or higher priority is already in progress. The current (polling) cycle is not in the final cycle of the instruction in progress. The instruction in progress is RETI or any write access to registers IEN0, IEN1, IEN2 or IP0 and IP1.
Any of these three conditions will block the generation of the LCALL to the interrupt service routine. Condition 2 ensures that the instruction in progress is completed before vectoring to any service routine. Condition 3 ensures that if the instruction in progress is RETI or any write access to registers IEN0, IEN1 or IP0 and IP1, then at least one more instruction will be executed before any interrupt is vectored too; this delay guarantees that changes of the interrupt status can be observed by the CPU.
Semiconductor Group
122
Interrupt System
The polling cycle is repeated with each machine cycle, and the values polled are the values that were present at S5P2 of the previous machine cycle. Note that if any interrupt flag is active but not being responded to for one of the conditions already mentioned, or if the flag is no longer active when the blocking condition is removed, the denied interrupt will not be serviced. In other words, the fact that the interrupt flag was once active but not serviced is not remembered. Every polling cycle interrogates only the pending interrupt requests. The polling cycle/LCALL sequence is illustrated in figure 8-9.
Figure 8-9 Interrupt Response Timing Diagram Note that if an interrupt of a higher priority level goes active prior to S5P2 in the machine cycle labeled C3 in figure 8-9, then, in accordance with the above rules, it will be vectored too during C5 and C6 without any instruction for the lower priority routine to be executed. Thus, the processor acknowledges an interrupt request by executing a hardware-generated LCALL to the appropriate servicing routine. In some cases it also clears the flag that generated the interrupt, while in other cases it does not; then this has to be done by the user's software. The hardware clears the external interrupt flags IE0 and lE1 only if they were transition-activated. The hardware-generated LCALL pushes the contents of the program counter onto the stack (but it does not save the PSW) and reloads the program counter with an address that depends on the source of the interrupt being vectored too, as shown in the following (table 8-2).
Semiconductor Group
123
Interrupt System
Table 8-2 Interrupt Sources and Vectors Interrupt Request Flags IE0 TF0 IE1 TF1 RI/TI TF2/EXF2 IADC IEX2 IEX3 IEX4 IEX5 IEX6 Interrupt Vector Address 0003H 000BH 0013H 001BH 0023H 002BH 0043H 004BH 0053H 005BH 0063H 006BH Interrupt Source External interrupt 0 Timer overflow External interrupt 1 Timer 1 overflow Serial channel Timer 2 overflow/ext. reload A/D converter External interrupt 2 External interrupt 3 External interrupt 4 External interrupt 5 External interrupt 6
Execution proceeds from that location until the RETI instruction is encountered. The RETI instruction informs the processor that the interrupt routine is no longer in progress, then pops the two top bytes from the stack and reloads the program counter. Execution of the interrupted program continues from the point where it was stopped. Note that the RETI instruction is very important because it informs the processor that the program left the current interrupt priority level. A simple RET instruction would also have returned execution to the interrupted program, but it would have left the interrupt control system thinking an interrupt was still in progress. In this case no interrupt of the same or lower priority level would be acknowledged.
Semiconductor Group
124
Interrupt System
8.4
External Interrupts
The external interrupts 0 and 1 can be programmed to be level-activated or negative-transition activated by setting or clearing bit IT0 or IT1, respectively, in register TCON (see figure 8-4). lf ITx = 0 (x = 0 or 1), external interrupt x is triggered by a detected low level at the INTx pin. lf ITx = 1, external interrupt x is negative edge-triggered. In this mode, if successive samples of the INTx pin show a high in one cycle and a low in the next cycle, interrupt request flag lEx in TCON is set. Flag bit lEx then requests the interrupt. lf the external interrupt 0 or 1 is level-activated, the external source has to hold the request active until the requested interrupt is actually generated. Then it has to deactivate the request before the interrupt service routine is completed, or else another interrupt will be generated. The external interrupts 2 and 3 can be programmed to be negative or positive transition-activated by setting or clearing bit I2FR or I3FR in register T2CON (see figure 8-5). lf IxFR = 0 (x = 2 or 3), external interrupt x is negative transition-activated. lf IxFR = 1, external interrupt is triggered by a positive transition. The external interrupts 4, 5, and 6 are activated by a positive transition. The external timer 2 reload trigger interrupt request flag EXF2 will be activated by a negative transition at pin P1.5/T2EX but only if bit EXEN2 is set. Since the external interrupt pins (INT2 to INT6) are sampled once in each machine cycle, an input high or low should be held for at least 12 oscillator periods to ensure sampling. lf the external interrupt is transition-activated, the external source has to hold the request pin low (high for INT2 and INT3, if it is programmed to be negative transition-active) for at least one cycle, and then hold it high (low) for at least one cycle to ensure that the transition is recognized so that the corresponding interrupt request flag will be set (see figure 8-10). The external interrupt request flags will automatically be cleared by the CPU when the service routine is called.
Semiconductor Group
125
Interrupt System
Figure 8-10 External Interrupt Detection 8.5 Response Time
lf an external interrupt is recognized, its corresponding request flag is set at S5P2 in every machine cycle. The value is not polled by the circuitry until the next machine cycle. lf the request is active and conditions are right for it to be acknowledged, a hardware subroutine call to the requested service routine will be the next instruction to be executed. The call itself takes two cycles. Thus a minimum of three complete machine cycles will elapse between activation and external interrupt request and the beginning of execution of the first instruction of the service routine. A longer response time would be obtained if the request was blocked by one of the three previously listed conditions. lf an interrupt of equal or higher priority is already in progress, the additional wait time obviously depends on the nature of 'the other interrupt's service routine. lf the instruction in progress is not in its final cycle, the additional wait time cannot be more than 3 cycles since the longest instructions (MUL and DIV) are only 4 cycles long; and, if the instruction in progress is RETI or a write access to registers IEN0, IEN1 or IP0, IP1, the additional wait time cannot be more than 5 cycles (a maximum of one more cycle to complete the instruction in progress, plus 4 cycles to complete the next instruction, if the instruction is MUL or DIV). Thus, in a single interrupt system, the response time is always more than 3 cycles and less than 9 cycles.
Semiconductor Group
126
Instruction Set
9
Instruction Set
The SAB 80(C)515/80(C)535 instruction set includes 111 instructions, 49 of which are single-byte, 45 two-byte and 17 three-byte instructions. The instruction opcode format consists of a function mnemonic followed by a "destination, source" operand field. This field specifies the data type and addressing method(s) to be used. Like all other members of the 8051-family, the SAB 80(C)515/80(C)535 can be programmed with the same instruction set common to the basic member, the SAB 8051. Thus, the SAB 80(C)515/80(C)535 is 100% software compatible to the SAB 8051 and may be programmed with 8051 assembler or high-level languages. 9.1 Addressing Modes
The SAB 80(C)515/80(C)535 uses five addressing modes: - - - - - register direct immediate register indirect base register plus index-register indirect
Table 9-1 summarizes the memory spaces which may be accessed by each of the addressing modes. Register Addressing Register addressing accesses the eight working registers (R0 - R7) of the selected register bank. The least significant bit of the instruction opcode indicates which register is to be used. ACC, B, DPTR and CY, the Boolean processor accumulator, can also be addressed as registers. Direct Addressing Direct addressing is the only method of accessing the special function registers. The lower 128 bytes of internal RAM are also directly addressable. Immediate Addressing Immediate addressing allows constants to be part of the instruction in program memory.
Semiconductor Group
127
Instruction Set
Table 9-1 Addressing Modes and Associated Memory Spaces Addressing Modes Register addressing Direct addressing Immediate addressing Register indirect addressing Base register plus index register addressing Register Indirect Addressing Register indirect addressing uses the contents of either R0 or R1 (in the selected register bank) as a pointer to locations in a 256-byte block: the 256 bytes of internal RAM or the lower 256 bytes of external data memory. Note that the special function registers are not accessible by this method. The upper half of the internal RAM can be accessed by indirect addressing only. Access to the full 64 Kbytes of external data memory address space is accomplished by using the 16-bit data pointer. Execution of PUSH and POP instructions also uses register indirect addressing. The stack may reside anywhere in the internal RAM. Base Register plus Index Register Addressing Base register plus index register addressing allows a byte to be accessed from program memory via an indirect move from the location whose address is the sum of a base register (DPTR or PC) and index register, ACC. This mode facilitates look-up table accesses. Boolean Processor The Boolean processor is a bit processor integrated into the SAB 80(C)515/80(C)535. It has its own instruction set, accumulator (the carry flag), bit-addressable RAM and l/O. Associated Memory Spaces R0 through R7 of selected register bank, ACC, B, CY (Bit), DPTR Lower 128 bytes of internal RAM, special function registers Program memory Internal RAM (@R1, @R0, SP), external data memory (@R1, @R0, @DPTR) Program memory (@DPTR + A, @PC + A)
Semiconductor Group
128
Instruction Set
The Bit Manipulation Instructions allow: - - - - - - - set bit clear bit complement bit jump if bit is set jump if bit is not set jump if bit is set and clear bit move bit from / to carry
Addressable bits, or their complements, may be logically AND-ed or OR-ed with the contents of the carry flag. The result is returned to the carry register. 9.2 Introduction to the Instruction Set
The instruction set is divided into four functional groups: - - - - 9.2.1 data transfer arithmetic logic control transfer Data Transfer
Data operations are divided into three classes: - general-purpose - accumulator-specific - address-object None of these operations affects the PSW flag settings except a POP or MOV directly to the PSW.
Semiconductor Group
129
Instruction Set
General-Purpose Transfers - MOV performs a bit or byte transfer from the source operand to the destination operand. - PUSH increments the SP register and then transfers a byte from the source operand to the stack location currently addressed by SP. - POP transfers a byte operand from the stack location addressed by the SP to the destination operand and then decrements SP. Accumulator-Specific Transfers - XCH exchanges the byte source operand with register A (accumulator). - XCHD exchanges the low-order nibble of the source operand byte with the low-order nibble of A. - MOVX performs a byte move between the external data memory and the accumulator. The external address can be specified by the DPTR register (16 bit) or the R1 or R0 register (8 bit). - MOVC moves a byte from program memory to the accumulator. The operand in A is used as an index into a 256-byte table pointed to by the base register (DPTR or PC). The byte operand accessed is transferred to the accumulator. Address-Object Transfer - MOV DPTR, #data loads 16 bits of immediate data into a pair of destination registers, DPH and DPL. 9.2.2 Arithmetic
The SAB 80(C)515/80(C)535 has four basic mathematical operations. Only 8-bit operations using unsigned arithmetic are supported directly. The overflow flag, however, permits the addition and subtraction operation to serve for both unsigned and signed binary integers. Arithmetic can also be performed directly on packed BCD representations. Addition - INC (increment) adds one to the source operand and puts the result in the operand. - ADD adds A to the source operand and returns the result to A. - ADDC (add with carry) adds A and the source operand, then adds one (1) if CY is set, and puts the result in A. - DA (decimal-add-adjust for BCD addition) corrects the sum which results from the binary addition of two-digit decimal operands. The packed decimal sum formed by DA is returned to A. CY is set if the BCD result is greater than 99; otherwise, it is cleared.
Semiconductor Group
130
Instruction Set
Subtraction - SUBB (subtract with borrow) subtracts the second source operand from the the first operand (the accumulator), subtracts one (1) if CY is set and returns the result to A. - DEC (decrement) subtracts one (1) from the source operand and returns the result to the operand. Multiplication - MUL performs an unsigned multiplication of the A register, returning a double byte result. A receives the low-order byte, B receives the high-order byte. OV is cleared if the top half of the result is zero and is set if it is not zero. CY is cleared. AC is unaffected. Division - DIV performs an unsigned division of the A register by the B register; it returns the integer quotient to the A register and returns the fractional remainder to the B register. Division by zero leaves indeterminate data in registers A and B and sets OV; otherwise, OV is cleared. CY is cleared. AC remains unaffected. Flags Unless otherwise stated in the previous descriptions, the flags of PSW are affected as follows: - CY is set if the operation causes a carry to or a borrow from the resulting high-order bit; otherwise CY is cleared. - AC is set if the operation results in a carry from the low-order four bits of the result (during addition), or a borrow from the high-order bits to the low-order bits (during subtraction); otherwise AC is cleared. - OV is set if the operation results in a carry to the high-order bit of the result but not a carry from the bit, or vice versa; otherwise OV is cleared. OV is used in two's-complement arithmetic, because it is set when the signal result cannot be represented in 8 bits. - P is set if the modulo-2 sum of the eight bits in the accumulator is 1 (odd parity); otherwise P is cleared (even parity). When a value is written to the PSW register, the P bit remains unchanged, as it always reflects the parity of A.
Semiconductor Group
131
Instruction Set
9.2.3
Logic
The SAB 80(C)515/80(C)535 performs basic logic operations on both bit and byte operands. Single-Operand Operations - CLR sets A or any directly addressable bit to zero (0). - SETB sets any directly bit-addressable bit to one (1). - CPL is used to complement the contents of the A register without affecting any flag, or any directly addressable bit location. - RL, RLC, RR, RRC, SWAP are the five operations that can be performed on A. RL, rotate left, RR, rotate right, RLC, rotate left through carry, RRC, rotate right through carry, and SWAP, rotate left four. For RLC and RRC the CY flag becomes equal to the last bit rotated out. SWAP rotates A left four places to exchange bits 3 through 0 with bits 7 through 4. Two-Operand Operations - ANL performs bitwise logical AND of two operands (for both bit and byte operands) and returns the result to the location of the first operand. - ORL performs bitwise logical OR of two source operands (for both bit and byte operands) and returns the result to the location of the first operand. - XRL performs logical Exclusive OR of two source operands (byte operands) and returns the result to the location of the first operand. 9.2.4 Control Transfer
There are three classes of control transfer operations: unconditional calls, returns, jumps, conditional jumps, and interrupts. All control transfer operations, some upon a specific condition, cause the program execution to continue a non-sequential location in program memory.
Semiconductor Group
132
Instruction Set
Unconditional Calls, Returns and Jumps Unconditional calls, returns and jumps transfer control from the current value of the program counter to the target address. Both direct and indirect transfers are supported. - ACALL and LCALL push the address of the next instruction onto the stack and then transfer control to the target address. ACALL is a 2-byte instruction used when the target address is in the current 2K page. LCALL is a 3-byte instruction that addresses the full 64K program space. In ACALL, immediate data (i.e. an 11-bit address field) is concatenated to the five most significant bits of the PC (which is pointing to the next instruction). If ACALL is in the last 2 bytes of a 2K page then the call will be made to the next page since the PC will have been incremented to the next instruction prior to execution. - RET transfers control to the return address saved on the stack by a previous call operation and decrements the SP register by two (2) to adjust the SP for the popped address. - AJMP, LJMP and SJMP transfer control to the target operand. The operation of AJMP and LJMP are analogous to ACALL and LCALL. The SJMP (short jump) instruction provides for transfers within a 256-byte range centered about the starting address of the next instruction (- 128 to + 127). - JMP @A + DPTR performs a jump relative to the DPTR register. The operand in A is used as the offset (0 - 255) to the address in the DPTR register. Thus, the effective destination for a jump can be anywhere in the program memory space. Conditional Jumps Conditional jumps perform a jump contingent upon a specific condition. The destination will be within a 256-byte range centered about the starting address of the next instruction (- 128 to + 127). JZ performs a jump if the accumulator is zero. JNZ performs a jump if the accumulator is not zero. JC performs a jump if the carry flag is set. JNC performs a jump if the carry flag is not set. JB performs a jump if the directly addressed bit is set. JNB performs a jump if the directly addressed bit is not set. JBC performs a jump if the directly addressed bit is set and then clears the directly addressed bit. - CJNE compares the first operand to the second operand and performs a jump if they are not equal. CY is set if the first operand is less than the second operand; otherwise it is cleared. Comparisons can be made between A and directly addressable bytes in internal data memory or an immediate value and either A, a register in the selected register bank, or a register indirectly addressable byte of the internal RAM. - DJNZ decrements the source operand and returns the result to the operand. A jump is performed if the result is not zero. The source operand of the DJNZ instruction may be any directly addressable byte in the internal data memory. Either direct or register addressing may be used to address the source operand. Interrupt Returns - RETI transfers control as RET does, but additionally enables interrupts of the current priority level. - - - - - - -
Semiconductor Group
133
Instruction Set
9.3
Instruction Definitions
All 111 instructions of the SAB 80(C)515/80(C)535 can essentially be condensed to 54 basic operations, in the following alphabetically ordered according to the operation mnemonic section.
Instruction CY ADD ADDC SUBB MUL DIV DA RRC RLC CJNE X X X 0 0 X X X X
Flag OV X X X X X AC X X X
Instruction CY SETB C CLR C CPL C ANL C,bit ANL C,/bit ORL C,bit ORL C,/bit MOV C,bit 1 0 X X X X X X
Flag OV AC
A brief example of how the instruction might be used is given as well as its effect on the PSW flags. The number of bytes and machine cycles required, the binary machine language encoding, and a symbolic description or restatement of the function is also provided. Note: Only the carry, auxiliary carry, and overflow flags are discussed. The parity bit is computed after every instruction cycle that alters the accumulator. Similarily, instructions which alter directly addressed registers could affect the other status flags if the instruction is applied to the PSW. Status flags can also be modified by bit manipulation.
Semiconductor Group
134
Instruction Set
Notes on Data Addressing Modes Rn direct @Ri #data #data 16 bit A Working register R0-R7 128 internal RAM locations, any l/O port, control or status register Indirect internal or external RAM location addressed by register R0 or R1 8-bit constant included in instruction 16-bit constant included as bytes 2 and 3 of instruction 128 software flags, any bitaddressable l/O pin, control or status bit Accumulator
Notes on Program Addressing Modes addr16 addr11 rel Destination address for LCALL and LJMP may be anywhere within the 64-Kbyte program memory address space. Destination address for ACALL and AJMP will be within the same 2-Kbyte page of program memory as the first byte of the following instruction. SJMP and all conditional jumps include an 8 bit offset byte. Range is + 127/- 128 bytes relative to the first byte of the following instruction.
(c)
All mnemonics copyrighted:
Intel Corporation 1980
Semiconductor Group
135
Instruction Set
ACALL Function:
addr11 Absolute call ACALL unconditionally calls a subroutine located at the indicated address. The instruction increments the PC twice to obtain the address of the following instruction, then pushes the 16-bit result onto the stack (low-order byte first) and increments the stack pointer twice. The destination address is obtained by successively concatenating the five high-order bits of the incremented PC, op code bits 7-5, and the second byte of the instruction. The subroutine called must therefore start within the same 2K block of program memory as the first byte of the instruction following ACALL. No flags are affected. Initially SP equals 07H. The label "SUBRTN" is at program memory location 0345H. After executing the instruction ACALL SUBRTN
Description:
Example:
at location 0123H, SP will contain 09H, internal RAM location 08H and 09H will contain 25H and 01H, respectively, and the PC will contain 0345H. Operation: ACALL (PC) (PC) + 2 (SP) (SP) + 1 ((SP)) (PC7-0) (SP) (SP) + 1 ((SP)) (PC15-8) (PC10-0) page address a10 a9 a8 1 2 2 0001 a7 a6 a5 a4 a3 a2 a1 a0
Encoding: Bytes: Cycles:
Semiconductor Group
136
Instruction Set
ADD Function:
A, Add ADD adds the byte variable indicated to the accumulator, leaving the result in the accumulator. The carry and auxiliary carry flags are set, respectively, if there is a carry out of bit 7 or bit 3, and cleared otherwise. When adding unsigned integers, the carry flag indicates an overflow occurred. OV is set if there is a carry out of bit 6 but not out of bit 7, or a carry out of bit 7 but not out of bit 6; otherwise OV is cleared. When adding signed integers, OV indicates a negative number produced as the sum of two positive operands, or a positive sum from two negative operands. Four source operand addressing modes are allowed: register, direct, registerindirect, or immediate.
Description:
Example:
The accumulator holds 0C3 H (11000011B) and register 0 holds 0AAH (10101010B). The instruction ADD A,R0
will leave 6DH (01101101B) in the accumulator with the AC flag cleared and both the carry flag and OV set to 1. ADD Operation: A,Rn ADD (A) (A) + (Rn) 0010 1 1 A,direct ADD (A) (A) + (direct) 0010 2 1 0101 direct address 1rrr
Encoding: Bytes: Cycles: ADD Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
137
Instruction Set
ADD Operation:
A, @Ri ADD (A) (A) + ((Ri)) 0010 1 1 A, #data ADD (A) (A) + #data 0010 2 1 0100 immediate data 011i
Encoding: Bytes: Cycles: ADD Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
138
Instruction Set
ADDC Function:
A, < src-byte> Add with carry ADDC simultaneously adds the byte variable indicated, the carry flag and the accumulator contents, leaving the result in the accumulator. The carry and auxiliary carry flags are set, respectively, if there is a carry out of bit 7 or bit 3, and cleared otherwise. When adding unsigned integers, the carry flag indicates an overflow occurred. OV is set if there is a carry out of bit 6 but not out of bit 7, or a carry out of bit 7 but not out of bit 6; otherwise OV is cleared. When adding signed integers, OV indicates a negative number produced as the sum of two positive operands or a positive sum from two negative operands. Four source operand addressing modes are allowed: register, direct, registerindirect, or immediate.
Description:
Example:
The accumulator holds 0C3 H (11000011B) and register 0 holds 0AAH (10101010B) with the carry flag set. The instruction ADDC A,R0
will leave 6EH (01101110B) in the accumulator with AC cleared and both the carry flag and OV set to 1. ADDC Operation: A,Rn ADDC (A) (A) + (C) + (Rn) 0011 1 1 A,direct ADDC (A) (A) + (C) + (direct) 0011 2 1 0101 direct address 1rrr
Encoding: Bytes: Cycles: ADDC Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
139
Instruction Set
ADDC Operation:
A, @Ri ADDC (A) (A) + (C) + ((Ri)) 0011 1 1 A, #data ADDC (A) (A) + (C) + #data 0011 2 1 0100 immediate data 011i
Encoding: Bytes: Cycles: ADDC Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
140
Instruction Set
AJMP Function:
addr11 Absolute jump AJMP transfers program execution to the indicated address, which is formed at runtime by concatenating the high-order five bits of the PC (after incrementing the PC twice), op code bits 7-5, and the second byte of the instruction. The destination must therefore be within the same 2K block of program memory as the first byte of the instruction following AJMP. The label "JMPADR" is at program memory location 0123H. The instruction AJMP JMPADR is at location 0345H and will load the PC with 0123H.
Description:
Example:
Operation:
AJM P (PC) (PC) + 2 (PC10-0) page address a10 a9 a8 0 2 2 0001 a7 a6 a5 a4 a3 a2 a1 a0
Encoding: Bytes: Cycles:
Semiconductor Group
141
Instruction Set
ANL Function:

, Logical AND for byte variables ANL performs the bitwise logical AND operation between the variables indicated and stores the results in the destination variable. No flags are affected. The two operands allow six addressing mode combinations. When the destination is a accumulator, the source can use register, direct, register-indirect, or immediate addressing; when the destination is a direct address, the source can be the accumulator or immediate data. Note: When this instruction is used to modify an output port, the value used as the original port data will be read from the output data latch, not the input pins.
Description:
Example:
If the accumulator holds 0C3H (11000011B) and register 0 holds 0AAH (10101010B) then the instruction ANL A,R0
will leave 81H (10000001B) in the accumulator. When the destination is a directly addressed byte, this instruction will clear combinations of bits in any RAM location or hardware register. The mask byte determining the pattern of bits to be cleared would either be a constant contained in the instruction or a value computed in the accumulator at run-time. The instruction ANL P1, #01110011B
will clear bits 7, 3, and 2 of output port 1. ANL Operation: A,Rn ANL (A) (A) (Rn) 0101 1 1 1rrr
Encoding: Bytes: Cycles:
Semiconductor Group
142
Instruction Set
ANL Operation:
A,direct ANL (A) (A) (direct) 0101 2 1 A, @Ri ANL (A) (A) ((Ri)) 0101 1 1 A, #data ANL (A) (A) #data 0101 2 1 direct,A ANL (direct) (direct) (A) 0101 2 1 0101 direct address 0100 immediate data 011i 0101 direct address
Encoding: Bytes: Cycles: ANL Operation:
Encoding: Bytes: Cycles: ANL Operation:
Encoding: Bytes: Cycles: ANL Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
143
Instruction Set
ANL Operation:
direct, #data ANL (direct) (direct) #data 0101 3 2 0011 direct address immediate data
Encoding: Bytes: Cycles:
Semiconductor Group
144
Instruction Set
ANL Function:
C, Logical AND for bit variables If the Boolean value of the source bit is a logic 0 then clear the carry flag; otherwise leave the carry flag in its current state. A slash ("/" preceding the operand in the assembly language indicates that the logical complement of the addressed bit is used as the source value, but the source bit itself is not affected. No other flags are affected. Only direct bit addressing is allowed for the source operand.
Description:
Example:
Set the carry flag if, and only if, P1.0 = 1, ACC.7 = 1, and OV = 0: MOV ANL ANL C,P1.0 C,ACC.7 C,/OV ; Load carry with input pin state ; AND carry with accumulator bit 7 ; AND with inverse of overflow flag
ANL Operation:
C,bit ANL (C) (C) (bit) 1000 2 2 C,/bit ANL (C) (C) (bit) 1011 2 2 0000 bit address 0010 bit address
Encoding: Bytes: Cycles: ANL Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
145
Instruction Set
CJNE Function:

, < src-byte >, rel Compare and jump if not equal CJNE compares the magnitudes of the tirst two operands, and branches if their values are not equal. The branch destination is computed by adding the signed relative displacement in the last instruction byte to the PC, after incrementing the PC to the start of the next instruction. The carry flag is set if the unsigned integer value of is less than the unsigned integer value of ; otherwise, the carry is cleared. Neither operand is affected. The first two operands allow four addressing mode combinations: the accumulator may be compared with any directly addressed byte or immediate data, and any indirect RAM location or working register can be compared with an immediate constant.
Description:
Example:
The accumulator contains 34 H. Register 7 contains 56H. The first instruction in the sequence ; NOT_EQ ; CJNE ... JC ... R7, # 60H, NOT_EQ ..... REQ_LOW ..... ; R7 = 60H ; If R7 < 60H ; R7 > 60H
sets the carry flag and branches to the instruction at label NOT_EQ. By testing the carry flag, this instruction determines whether R7 is greater or less than 60H. If the data being presented to port 1 is also 34 H, then the instruction WAIT: CJNE A,P1,WAIT clears the carry flag and continues with the next instruction in sequence, since the accumulator does equal the data read from P1. (If some other value was input on P1, the program will loop at this point until the P1 data changes to 34 H).
Semiconductor Group
146
Instruction Set
CJNE Operation:
A,direct,rel (PC) (PC) + 3 if (A) < > (direct) then (PC) (PC) + relative offset if (A) < (direct) then (C) 1 else (C) 0 1011 3 2 A, #data,rel (PC) (PC) + 3 if (A) < > data then (PC) (PC) + relative offset if (A) data then (C) 1 else (C) 0 1011 3 2 RN, #data, rel (PC) (PC) + 3 if (Rn) < > data then (PC) (PC) + relative offset if (Rn) < data then (C) 1 else (C) 0 1011 3 2 1rrr immediate data rel. address 0100 immediate data rel. address 0101 direct address rel. address
Encoding: Bytes: Cycles: CJNE Operation:
Encoding: Bytes: Cycles: CJNE Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
147
Instruction Set
CJNE Operation:
@Ri, #data,rel (PC) (PC) + 3 if ((Ri)) < > data then (PC) (PC) + relative offset if ((Ri)) < data then (C) 1 else (C) 0 1011 3 2 011i immediate data rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
148
Instruction Set
CLR Function:
A Clear accumulator The accumulator is cleared (all bits set to zero). No flags are affected. The accumulator contains 5CH (01011100B). The instruction CLR A will leave the accumulator set to 00H (00000000B).
Description: Example:
Operation:
CLR (A) 0 1110 1 1 0100
Encoding: Bytes: Cycles:
Semiconductor Group
149
Instruction Set
CLR Function:
bit Clear bit The indicated bit is cleared (reset to zero). No other flags are affected. CLR can operate on the carry flag or any directly addressable bit. Port 1 has previously been written with 5D H (01011101B). The instruction CLR P1.2 will leave the port set to 59H (01011001B).
Description: Example:
CLR Operation:
C CLR (C) 0 1100 1 1 bit CLR (bit) 0 1100 2 1 0010 bit address 0011
Encoding: Bytes: Cycles: CLR Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
150
Instruction Set
CPL Function:
A Complement accumulator Each bit of the accumulator is logically complemented (one's complement). Bits which previously contained a one are changed to zero and vice versa. No flags are affected. The accumulator contains 5CH (01011100B). The instruction CPL A will leave the accumulator set to 0A3H (10100011 B).
Description:
Example:
Operation:
CPL (A) (A) 1111 1 1 0100
Encoding: Bytes: Cycles:
Semiconductor Group
151
Instruction Set
CPL Function:
bit Complement bit The bit variable specified is complemented. A bit which had been a one is changed to zero and vice versa. No other flags are affected. CPL can operate on the carry or any directly addressable bit. Note: When this instruction is used to modify an output pin, the value used as the original data will be read from the output data latch, not the input pin.
Description:
Example:
Port 1 has previously been written with 5DH (01011101B). The instruction sequence CPL CPL P1.1 P1.2
will leave the port set to 5BH (01011011B). CPL Operation: C CPL (C) (C) 1011 1 1 bit CPL (bit) (bit) 1011 2 1 0010 bit address 0011
Encoding: Bytes: Cycles: CPL Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
152
Instruction Set
DA Function:
A Decimal adjust accumulator for addition DA A adjusts the eight-bit value in the accumulator resulting from the earlier addition of two variables (each in packed BCD format), producing two four-bit digits. Any ADD or ADDC instruction may have been used to perform the addition. If accumulator bits 3-0 are greater than nine (xxxx1010-xxxx1111), or if the AC flag is one, six is added to the accumulator producing the proper BCD digit in the loworder nibble. This internal addition would set the carry flag if a carry-out of the loworder four-bit field propagated through all high-order bits, but it would not clear the carry flag otherwise. If the carry flag is now set, or if the four high-order bits now exceed nine (1010xxxx1111xxxx), these high-order bits are incremented by six, producing the proper BCD digit in the high-order nibble. Again, this would set the carry flag if there was a carryout of the high-order bits, but wouldn't clear the carry. The carry flag thus indicates if the sum of the original two BCD variables is greater than 100, allowing multiple precision decimal addition. OV is not affected. All of this occurs during the one instruction cycle. Essentially; this instruction performs the decimal conversion by adding 00H, 06H, 60H, or 66H to the accumulator, depending on initial accumulator and PSW conditions. Note: DA A cannot simply convert a hexadecimal number in the accumulator to BCD notation, nor does DA A apply to decimal subtraction.
Description:
Example:
The accumulator holds the value 56H (01010110B) representing the packed BCD digits of the decimal number 56. Register 3 contains the value 67H (01100111B) representing the packed BCD digits of the decimal number 67. The carry flag is set. The instruction sequence ADDC DA A,R3 A
will first perform a standard two's-complement binary addition, resulting in the value 0BEH (10111110B) in the accumulator. The carry and auxiliary carry flags will be cleared. The decimal adjust instruction will then alter the accumulator to the value 24H (00100100B), indicating the packed BCD digits of the decimal number 24, the loworder two digits of the decimal sum of 56, 67, and the carry-in. The carry flag will be set by the decimal adjust instruction, indicating that a decimal overflow occurred. The true sum 56, 67, and 1 is 124.
Semiconductor Group
153
Instruction Set
BCD variables can be incremented or decremented by adding 01H or 99H. If the accumulator initially holds 30H (representing the digits of 30 decimal), then the instruction sequence ADD DA A, #99H A
will leave the carry set and 29H in the accumulator, since 30 + 99 = 129. The loworder byte of the sum can be interpreted to mean 30 - 1 = 29. Operation: DA contents of accumulator are BCD if [[(A3-0) > 9] [(AC) = 1]] then (A3-0) (A3-0) + 6 and if [[(A7-4) > 9] [(C) = 1]] then (A7-4) (A7-4) + 6 1101 1 1 0100
Encoding: Bytes: Cycles:
Semiconductor Group
154
Instruction Set
DEC Function:
byte Decrement The variable indicated is decremented by 1. An original value of 00H will underflow to 0FFH. No flags are affected. Four operand addressing modes are allowed: accumulator, register, direct, or register-indirect. Note: When this instruction is used to modify an output port, the value used as the original port data will be read from the output data latch, not the input pins.
Description:
Example:
Register 0 contains 7FH (01111111B). Internal RAM locations 7EH and 7FH contain 00H and 40H, respectively. The instruction sequence DEC DEC DEC @R0 R0 @R0
will leave register 0 set to 7EH and internal RAM locations 7EH and 7FH set to 0FFH and 3FH. DEC Operation: A DEC (A) (A) - 1 0001 1 1 Rn DEC (Rn) (Rn) - 1 0001 1 1 1rrr 0100
Encoding: Bytes: Cycles: DEC Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
155
Instruction Set
DEC Operation:
direct DEC (direct) (direct) - 1 0001 2 1 @Ri DEC ((Ri)) ((Ri)) - 1 0001 1 1 011i 0101 direct address
Encoding: Bytes: Cycles: DEC Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
156
Instruction Set
DIV Function:
AB Divide DIV AB divides the unsigned eight-bit integer in the accumulator by the unsigned eight-bit integer in register B. The accumulator receives the integer part of the quotient; register B receives the integer remainder. The carry and OV flags will be cleared.
Description:
Exception: If B had originally contained 00H, the values returned in the accumulator and B register will be undefined and the overflow flag will be set. The carry flag is cleared in any case.
Example: The accumulator contains 251 (0FBH or 11111011B) and B contains 18 (12H or 00010010B). The instruction DIV AB
will leave 13 in the accumulator (0DH or 00001101 B) and the value 17 (11H or 00010001B) in B, since 251 = (13x18) + 17. Carry and OV will both be cleared. Operation: DIV (A15-8) (B7-0) (A) / (B)
Encoding: Bytes: Cycles:
1000 1 4
0100
Semiconductor Group
157
Instruction Set
DJNZ Function:
, < rel-addr> Decrement and jump if not zero DJNZ decrements the location indicated by 1, and branches to the address indicated by the second operand if the resulting value is not zero. An original value of 00H will underflow to 0FFH. No flags are affected. The branch destination would be computed by adding the signed relative-displacement value in the last instruction byte to the PC, after incrementing the PC to the first byte of the following instruction. The location decremented may be a register or directly addressed byte. Note: When this instruction is used to modify an output port, the value used as the original port data will be read from the output data latch, not the input pins.
Description:
Example:
Internal RAM locations 40H, 50H, and 60H contain the values, 01H, 70H, and 15H, respectively. The instruction sequence DJNZ 40H,LABEL_1 DJNZ 50H,LABEL_2 DJNZ 60H,LABEL_3 will cause a jump to the instruction at label LABEL_2 with the values 00 H, 6FH, and 15H in the three RAM locations. The first jump was not taken because the result was zero. This instruction provides a simple way of executing a program loop a given number of times, or for adding a moderate time delay (from 2 to 512 machine cycles) with a single instruction. The instruction sequence MOV TOGGLE: CPL DJNZ R2, #8 P1.7 R2,TOGGLE
will toggle P1.7 eight times, causing four output pulses to appear at bit 7 of output port 1. Each pulse will last three machine cycles; two for DJNZ and one to alter the pin.
Semiconductor Group
158
Instruction Set
DJNZ Operation:
Rn,rel DJNZ (PC) (PC) + 2 (Rn) (Rn) - 1 if (Rn) > 0 or (Rn) < 0 then (PC) (PC) + rel 1101 2 2 direct,rel DJNZ (PC) (PC) + 2 (direct) (direct) - 1 if (direct) > 0 or (direct) < 0 then (PC) (PC) + rel 1101 3 2 0101 direct address rel. address 1rrr rel. address
Encoding: Bytes: Cycles: DJNZ Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
159
Instruction Set
INC Function:
Increment INC increments the indicated variable by 1. An original value of 0FF H will overflow to 00H. No flags are affected. Three addressing modes are allowed: register, direct, or register-indirect. Note: When this instruction is used to modify an output port, the value used as the original port data will be read from the output data latch, not the input pins.
Description:
Example:
Register 0 contains 7EH (01111110B). Internal RAM locations 7EH and 7FH contain 0FFH and 40H, respectively. The instruction sequence INC INC INC @R0 R0 @R0
will leave register 0 set to 7FH and internal RAM locations 7EH and 7FH holding (respectively) 00H and 41H. INC Operation: A INC (A) (A) + 1 0000 1 1 Rn INC (Rn) (Rn) + 1 0000 1 1 1rrr 0100
Encoding: Bytes: Cycles: INC Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
160
Instruction Set
INC Operation:
direct INC (direct) (direct) + 1 0000 2 1 @Ri INC ((Ri)) ((Ri)) + 1 0000 1 1 011i 0101 direct address
Encoding: Bytes: Cycles: INC Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
161
Instruction Set
INC Function:
DPTR Increment data pointer Increment the 16-bit data pointer by 1. A 16-bit increment (modulo 2 16) is performed; an overflow of the low-order byte of the data pointer (DPL) from 0FFH to 00H will increment the high-order byte (DPH). No flags are affected. This is the only 16-bit register which can be incremented.
Description:
Example:
Registers DPH and DPL contain 12H and 0FEH, respectively. The instruction sequence INC INC INC DPTR DPTR DPTR
will change DPH and DPL to 13H and 01H. Operation: INC (DPTR) (DPTR) + 1 1010 1 2 0011
Encoding: Bytes: Cycles:
Semiconductor Group
162
Instruction Set
JB Function:
bit,rel Jump if bit is set If the indicated bit is a one, jump to the address indicated; otherwise proceed with the next instruction. The branch destination is computed by adding the signed relative-displacement in the third instruction byte to the PC, after incrementing the PC to the first byte of the next instruction. The bit tested is not modified. No flags are affected. The data present at input port 1 is 11001010B. The accumulator holds 56 (01010110B). The instruction sequence JB JB P1.2,LABEL1 ACC.2,LABEL2
Description:
Example:
will cause program execution to branch to the instruction at label LABEL2. Operation: JB (PC) (PC) + 3 if (bit) = 1 then (PC) (PC) + rel 0010 3 2 0000 bit address rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
163
Instruction Set
JBC Function:
bit,rel Jump if bit is set and clear bit If the indicated bit is one, branch to the address indicated; otherwise proceed with the next instruction. In either case, clear the designated bit. The branch destination is computed by adding the signed relative displacement in the third instruction byte to the PC, after incrementing the PC to the first byte of the next instruction. No flags are affected. Note: When this instruction is used to test an output pin, the value used as the original data will be read from the output data latch, not the input pin.
Description:
Example:
The accumulator holds 56H (01010110B). The instruction sequence JBC JBC ACC.3,LABEL1 ACC.2,LABEL2
will cause program execution to continue at the instruction identified by the label LABEL2, with the accumulator modified to 52H (01010010B). Operation: JBC (PC) (PC) + 3 if (bit) = 1 then (bit) 0 (PC) (PC) + rel 0001 3 2 0000 bit address rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
164
Instruction Set
JC Function:
rel Jump if carry is set If the carry flag is set, branch to the address indicated; otherwise proceed with the next instruction. The branch destination is computed by adding the signed relativedisplacement in the second instruction byte to the PC, after incrementing the PC twice. No flags are affected. The carry flag is cleared. The instruction sequence JC CPL JC LABEL1 C LABEL2
Description:
Example:
will set the carry and cause program execution to continue at the instruction identified by the label LABEL2. Operation: JC (PC) (PC) + 2 if (C) = 1 then (PC) (PC) + rel 0100 2 2 0000 rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
165
Instruction Set
JMP Function:
@A + DPTR Jump indirect Add the eight-bit unsigned contents of the accumulator with the sixteen-bit data pointer, and load the resulting sum to the program counter. This will be the address for subsequent instruction fetches. Sixteen-bit addition is performed (modulo 216): a carry-out from the low-order eight bits propagates through the higher-order bits. Neither the accumulator nor the data pointer is altered. No flags are affected. An even number from 0 to 6 is in the accumulator. The following sequence of instructions will branch to one of four AJMP instructions in a jump table starting at JMP_TBL: MOV JMP JMP_TBL: AJMP AJMP AJMP AJMP DPTR, #JMP_TBL @A + DPTR LABEL0 LABEL1 LABEL2 LABEL3
Description:
Example:
If the accumulator equals 04 H when starting this sequence, execution will jump to label LABEL2. Remember that AJMP is a two-byte instruction, so the jump instructions start at every other address. Operation: JMP (PC) (A) + (DPTR) 0111 1 2 0011
Encoding: Bytes: Cycles:
Semiconductor Group
166
Instruction Set
JNB Function:
bit,rel Jump if bit is not set If the indicated bit is a zero, branch to the indicated address; otherwise proceed with the next instruction. The branch destination is computed by adding the signed relative-displacement in the third instruction byte to the PC, after incrementing the PC to the first byte of the next instruction. The bit tested is not modified. No flags are affected. The data present at input port 1 is 11001010B. The accumulator holds 56 H (01010110B). The instruction sequence JNB JNB P1.3,LABEL1 ACC.3,LABEL2
Description:
Example:
will cause program execution to continue at the instruction at label LABEL2. Operation: JNB (PC) (PC) + 3 if (bit) = 0 then (PC) (PC) + rel. 0011 3 2 0000 bit address rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
167
Instruction Set
JNC Function:
rel Jump if carry is not set If the carry flag is a zero, branch to the address indicated; otherwise proceed with the next instruction. The branch destination is computed by adding the signed relative-displacement in the second instruction byte to the PC, after incrementing the PC twice to point to the next instruction. The carry flag is not modified. The carry flag is set. The instruction sequence JNC CPL JNC LABEL1 C LABEL2
Description:
Example:
will clear the carry and cause program execution to continue at the instruction identified by the label LABEL2. Operation: JNC (PC) (PC) + 2 if (C) = 0 then (PC) (PC) + rel 0101 2 2 0000 rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
168
Instruction Set
JNZ Function:
rel Jump if accumulator is not zero If any bit of the accumulator is a one, branch to the indicated address; otherwise proceed with the next instruction. The branch destination is computed by adding the signed relative-displacement in the second instruction byte to the PC, after incrementing the PC twice. The accumulator is not modified. No flags are affected. The accumulator originally holds 00H. The instruction sequence JNZ INC JNZ LABEL1 A LABEL2
Description:
Example:
will set the accumulator to 01H and continue at label LABEL2. Operation: JNZ (PC) (PC) + 2 if (A) 0 then (PC) (PC) + rel. 0111 2 2 0000 rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
169
Instruction Set
JZ Function:
rel Jump if accumulator is zero If all bits of the accumulator are zero, branch to the address indicated; otherwise proceed with the next instruction. The branch destination is computed by adding the signed relative-displacement in the second instruction byte to the PC, after incrementing the PC twice. The accumulator is not modified. No flags are affected. The accumulator originally contains 01 H. The instruction sequence JZ DEC JZ LABEL1 A LABEL2
Description:
Example:
will change the accumulator to 00H and cause program execution to continue at the instruction identified by the label LABEL2. Operation: JZ (PC) (PC) + 2 if (A) = 0 then (PC) (PC) + rel 0110 2 2 0000 rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
170
Instruction Set
LCALL Function:
addr16 Long call LCALL calls a subroutine located at the indicated address. The instruction adds three to the program counter to generate the address of the next instruction and then pushes the 16-bit result onto the stack (low byte first), incrementing the stack pointer by two. The high-order and low-order bytes of the PC are then loaded, respectively, with the second and third bytes of the LCALL instruction. Program execution continues with the instruction at this address. The subroutine may therefore begin anywhere in the full 64 Kbyte program memory address space. No flags are affected. Initially the stack pointer equals 07H. The label "SUBRTN" is assigned to program memory location 1234H. After executing the instruction LCALL SUBRTN at location 0123H, the stack pointer will contain 09H, internal RAM locations 08H and 09H will contain 26H and 01H, and the PC will contain 1234H.
Description:
Example:
Operation:
LCALL (PC) (PC) + 3 (SP) (SP) + 1 ((SP)) (PC7-0) (SP) (SP) + 1 ((SP)) (PC15-8) (PC) addr15-0 0001 3 2 0010 addr15 . . addr8 addr7 . . addr0
Encoding: Bytes: Cycles:
Semiconductor Group
171
Instruction Set
LJMP Function:
addr16 Long jump LJMP causes an unconditional branch to the indicated address, by loading the highorder and low-order bytes of the PC (respectively) with the second and third instruction bytes. The destination may therefore be anywhere in the full 64K program memory address space. No flags are affected. The label "JMPADR" is assigned to the instruction at program memory location 1234H. The instruction LJMP JMPADR at location 0123H will load the program counter with 1234H.
Description:
Example:
Operation:
LJMP (PC) addr15-0 0000 3 2 0010 addr15 . . . addr8 addr7 . . . addr0
Encoding: Bytes: Cycles:
Semiconductor Group
172
Instruction Set
MOV Function:

, Move byte variable The byte variable indicated by the second operand is copied into the location specified by the first operand. The source byte is not affected. No other register or flag is affected. This is by far the most flexible operation. Fifteen combinations of source and destination addressing modes are allowed.
Description:
Example:
Internal RAM location 30 H holds 40H. The value of RAM location 40 H is 10H. The data present at input port 1 is 11001010B (0CAH). MOV MOV MOV MOV MOV MOV R0, #30H A, @R0 R1,A B, @R1 @R1,P1 P2,P1 ; R0 < = 30H ; A < = 40H ; R1 < = 40H ; B < = 10H ; RAM (40H) < = 0CAH ; P2 < = 0CAH
leaves the value 30H in register 0, 40H in both the accumulator and register 1, 10H in register B, and 0CAH (11001010B) both in RAM location 40H and output on port 2. MOV Operation: A,Rn MOV (A) (Rn) 1110 1 1 A,direct *) MOV (A) (direct) 1110 2 1 0101 direct address 1rrr
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles:
*) MOV A,ACC is not a valid instruction.
Semiconductor Group
173
Instruction Set
MOV Operation:
A,@Ri MOV (A) ((Ri)) 1110 1 1 A, #data MOV (A) #data 0111 2 1 Rn,A MOV (Rn) (A) 1111 1 1 Rn,direct MOV (Rn) (direct) 1010 2 2 1rrr direct address 1rrr 0100 immediate data 011i
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
174
Instruction Set
MOV Operation:
Rn, #data MOV (Rn) #data 0111 2 1 direct,A MOV (direct) (A) 1111 2 1 direct,Rn MOV (direct) (Rn) 1000 2 2 direct,direct MOV (direct) (direct) 1000 3 2 0101 dir.addr. (src) dir.addr. (dest) 1rrr direct address 0101 direct address 1rrr immediate data
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
175
Instruction Set
MOV Operation:
direct, @ Ri MOV (direct) ((Ri)) 1000 2 2 direct, #data MOV (direct) #data 0111 3 2 @ Ri,A MOV ((Ri)) (A) 1111 1 1 @ Ri,direct MOV ((Ri)) (direct) 1010 2 2 011i direct address 011i 0101 direct address immediate data 011i direct address
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles: MOV Ooeration:
Encoding: Bytes: Cycles:
Semiconductor Group
176
Instruction Set
MOV Operation:
@ Ri,#data MOV ((Ri)) #data 0111 2 1 011i immediate data
Encoding: Bytes: Cycles:
Semiconductor Group
177
Instruction Set
MOV Function:

, Move bit data The Boolean variable indicated by the second operand is copied into the location specified by the first operand. One of the operands must be the carry flag; the other may be any directly addressable bit. No other register or flag is affected. The carry flag is originally set. The data present at input port 3 is 11000101B. The data previously written to output port 1 is 35 H (00110101B). MOV MOV MOV P1.3,C C,P3.3 P1.2,C
Description:
Example:
will leave the carry cleared and change port 1 to 39H (00111001 B). MOV Operation: C,bit MOV (C) (bit) 1010 2 1 bit,C MOV (bit) (C) 1001 2 2 0010 bit address 0010 bit address
Encoding: Bytes: Cycles: MOV Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
178
Instruction Set
MOV Function:
DPTR, #data16 Load data pointer with a 16-bit constant The data pointer is loaded with the 16-bit constant indicated. The 16 bit constant is loaded into the second and third bytes of the instruction. The second byte (DPH) is the high-order byte, while the third byte (DPL) holds the low-order byte. No flags are affected. This is the only instruction which moves 16 bits of data at once.
Description:
Example:
The instruction MOV DPTR, #1234H
will load the value 1234H into the data pointer: DPH will hold 12H and DPL will hold 34H. Operation: MOV (DPTR) #data15-0 DPH DPL #data15-8 1001 3 2 0000
#data7-0 immed. data 15 . . . 8 immed. data 7 . . . 0
Encoding: Bytes: Cycles:
Semiconductor Group
179
Instruction Set
MOVC Function:
A, @A + Move code byte The MOVC instructions load the accumulator with a code byte, or constant from program memory. The address of the byte fetched is the sum of the original unsigned eight-bit accumulator contents and the contents of a sixteen-bit base register, which may be either the data pointer or the PC. In the latter case, the PC is incremented to the address of the following instruction before being added to the accumulator; otherwise the base register is not altered. Sixteen-bit addition is performed so a carry-out from the low-order eight bits may propagate through higher-order bits. No flags are affected. A value between 0 and 3 is in the accumulator. The following instructions will translate the value in the accumulator to one of four values defined by the DB (define byte) directive. REL_PC: INC MOVC RET DB DB DB DB A A, @A + PC 66H 77H 88H 99H
Description:
Example:
If the subroutine is called with the accumulator equal to 01H, it will return with 77H in the accumulator. The INC A before the MOVC instruction is needed to "get around" the RET instruction above the table. If several bytes of code separated the MOVC from the table, the corresponding number would be added to the accumulator instead. MOVC Operation: A, @A + DPTR MOVC (A) ((A) + (DPTR)) 1001 1 2 0 01 1
Encoding: Bytes: Cycles:
Semiconductor Group
180
Instruction Set
MOVC Operation:
A, @A + PC MOVC (PC) (PC) + 1 (A) ((A) + (PC)) 1000 1 2 0 01 1
Encoding: Bytes: Cycles:
Semiconductor Group
181
Instruction Set
MOVX Function:

, Move external The MOVX instructions transfer data between the accumulator and a byte of external data memory, hence the "X" appended to MOV. There are two types of instructions, differing in whether they provide an eight bit or sixteen-bit indirect address to the external data RAM. In the first type, the contents of R0 or R1 in the current register bank provide an eight-bit address multiplexed with data on P0. Eight bits are sufficient for external l/O expansion decoding or a relatively small RAM array. For somewhat larger arrays, any output port pins can be used to output higher-order address bits. These pins would be controlled by an output instruction preceding the MOVX. In the second type of MOVX instructions, the data pointer generates a sixteen-bit address. P2 outputs the high-order eight address bits (the contents of DPH) while P0 multiplexes the low-order eight bits (DPL) with data. The P2 special function register retains its previous contents while the P2 output buffers are emitting the contents of DPH. This form is faster and more efficient when accessing very large data arrays (up to 64 Kbyte), since no additional instructions are needed to set up the output ports. It is possible in some situations to mix the two MOVX types. A large RAM array with its high-order address lines driven by P2 can be addressed via the data pointer, or with code to output high-order address bits to P2 followed by a MOVX instruction using R0 or R1.
Description:
Example:
An external 256 byte RAM using multiplexed address/data lines (e.g. an SAB 8155 RAM/I/O/timer) is connected to the SAB 80(c)5XX port 0. Port 3 provides control lines for the external RAM. Ports 1 and 2 are used for normal l/O. Registers 0 and 1 contain 12H and 34H. Location 34H of the external RAM holds the value 56 H. The instruction sequence MOVX MOVX A, @R1 @R0,A
copies the value 56H into both the accumulator and external RAM location 12H.
Semiconductor Group
182
Instruction Set
MOVX Operation:
A,@Ri MOVX (A) ((Ri)) 1110 1 2 A,@DPTR MOVX (A) ((DPTR)) 1110 1 2 @Ri,A MOVX ((Ri)) (A) 1111 1 2 @DPTR,A MOVX ((DPTR)) (A) 1111 1 2 0000 001i 0000 001i
Encoding: Bytes: Cycles: MOVX Operation:
Encoding: Bytes: Cycles: MOVX Operation:
Encoding: Bytes: Cycles: MOVX Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
183
Instruction Set
MUL Function:
AB Multiply MUL AB multiplies the unsigned eight-bit integers in the accumulator and register B. The low-order byte of the sixteen-bit product is left in the accumulator, and the high-order byte in B. If the product is greater than 255 (0FFH) the overflow flag is set; otherwise it is cleared. The carry flag is always cleared. Originally the accumulator holds the value 80 (50H). Register B holds the value 160 (0A0H). The instruction MUL AB will give the product 12,800 (3200H), so B is changed to 32H (00110010B) and the accumulator is cleared. The overflow flag is set, carry is cleared.
Description:
Example:
Operation:
MUL (A7-0) (A) x (B) (B15-8)
Encoding: Bytes: Cycles:
1010 1 4
0100
Semiconductor Group
184
Instruction Set
NOP Function: Description: Example: No operation Execution continues at the following instruction. Other than the PC, no registers or flags are affected. It is desired to produce a low-going output pulse on bit 7 of port 2 lasting exactly 5 cycles. A simple SETB/CLR sequence would generate a one-cycle pulse, so four additional cycles must be inserted. This may be done (assuming no interrupts are enabled) with the instruction sequence CLR P2.7 NOP NOP NOP NOP SETB P2.7 Operation: Encoding: Bytes: Cycles: NOP 0000 1 1 0000
Semiconductor Group
185
Instruction Set
ORL Function:

Logical OR for byte variables ORL performs the bitwise logical OR operation between the indicated variables, storing the results in the destination byte. No flags are affected . The two operands allow six addressing mode combinations. When the destination is the accumulator, the source can use register, direct, register-indirect, or immediate addressing; when the destination is a direct address, the source can be the accumulator or immediate data. Note: When this instruction is used to modify an output port, the value used as the original port data will be read from the output data latch, not the input pins.
Description:
Example:
If the accumulator holds 0C3H (11000011B) and R0 holds 55H (01010101B) then the instruction ORL A,R0
will leave the accumulator holding the value 0D7H (11010111B). When the destination is a directly addressed byte, the instruction can set combinations of bits in any RAM location or hardware register. The pattern of bits to be set is determined by a mask byte, which may be either a constant data value in the instruction or a variable computed in the accumulator at run-time. The instruction ORL P1,#00110010B
will set bits 5, 4, and 1 of output port 1. ORL Operation: A,Rn ORL (A) (A) (Rn) 0100 1 1 1rrr
Encoding: Bytes: Cycles:
Semiconductor Group
186
Instruction Set
ORL Operation:
A,direct ORL (A) (A) (direct) 0100 2 1 A,@Ri ORL (A) (A) ((Ri)) 0100 1 1 A,#data ORL (A) (A) #data 0100 2 1 direct,A ORL (direct) (direct) (A) 0100 2 1 0010 direct address 0100 immediate data 011i 0101 direct address
Encoding: Bytes: Cycles: ORL Operation:
Encoding: Bytes: Cycles: ORL Operation:
Encoding: Bytes: Cycles: ORL Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
187
Instruction Set
ORL Operation:
direct, #data ORL (direct) (direct) #data 0100 3 2 0011 direct address immediate data
Encoding: Bytes: Cycles:
Semiconductor Group
188
Instruction Set
ORL Function:
C, Logical OR for bit variables Set the carry flag if the Boolean value is a logic 1; leave the carry in its current state otherwise. A slash ("/") preceding the operand in the assembly language indicates that the logical complement of the addressed bit is used as the source value, but the source bit itself is not affected. No other flags are affected. Set the carry flag if, and only if, P1.0 = 1, ACC.7 = 1, or OV = 0: MOV ORL ORL C,P1.0 C,ACC.7 C,/OV ; Load carry with input pin P1.0 ; OR carry with the accumulator bit 7 ; OR carry with the inverse of OV
Description:
Example:
ORL Operation:
C,bit ORL (C) (C) (bit) 0111 2 2 C,/bit ORL (C) (C) (bit) 1010 2 2 0000 bit address 0010 bit address
Encoding: Bytes: Cycles: ORL Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
189
Instruction Set
POP Function:
direct Pop from stack The contents of the internal RAM location addressed by the stack pointer is read, and the stack pointer is decremented by one. The value read is the transfer to the directly addressed byte indicated. No flags are affected. The stack pointer originally contains the value 32 H, and internal RAM locations 30H through 32H contain the values 20H, 23H, and 01H, respectively. The instruction sequence POP POP DPH DPL
Description:
Example:
will leave the stack pointer equal to the value 30H and the data pointer set to 0123H. At this point the instruction POP SP
will leave the stack pointer set to 20H. Note that in this special case the stack pointer was decremented to 2FH before being loaded with the value popped (20H). Operation: POP (direct) ((SP)) (SP) (SP) - 1 1101 2 2 0000 direct address
Encoding: Bytes: Cycles:
Semiconductor Group
190
Instruction Set
PUSH Function:
direct Push onto stack The stack pointer is incremented by one. The contents of the indicated variable is then copied into the internal RAM location addressed by the stack pointer. Otherwise no flags are affected. On entering an interrupt routine the stack pointer contains 09H. The data pointer holds the value 0123H. The instruction sequence PUSH PUSH DPL DPH
Description:
Example:
will leave the stack pointer set to 0BH and store 23H and 01H in internal RAM locations 0AH and 0BH, respectively. Operation: PUSH (SP) (SP) + 1 ((SP)) (direct) 1100 2 2 0000 direct address
Encoding: Bytes: Cycles:
Semiconductor Group
191
Instruction Set
RET Function: Description: Return from subroutine RET pops the high and low-order bytes of the PC successively from the stack, decrementing the stack pointer by two. Program execution continues at the resulting address, generally the instruction immediately following an ACALL or LCALL. No flags are affected. The stack pointer originally contains the value 0B H. Internal RAM locations 0AH and 0BH contain the values 23H and 01H, respectively. The instruction RET will leave the stack pointer equal to the value 09H. Program execution will continue at location 0123H. Operation: RET (PC15-8) ((SP)) (SP) (SP) - 1 (PC7-0) ((SP)) (SP) (SP) - 1 0010 1 2 0010
Example:
Encoding: Bytes: Cycles:
Semiconductor Group
192
Instruction Set
RETI Function: Description: Return from interrupt RETI pops the high and low-order bytes of the PC successively from the stack, and restores the interrupt logic to accept additional interrupts at the same priority level as the one just processed. The stack pointer is left decremented by two. No other registers are affected; the PSW is not automatically restored to its pre-interrupt status. Program execution continues at the resulting address, which is generally the instruction immediately after the point at which the interrupt request was detected. If a lower or same-level interrupt is pending when the RETI instruction is executed, that one instruction will be executed before the pending interrupt is processed. The stack pointer originally contains the value 0BH. An interrupt was detected during the instruction ending at location 0122H. Internal RAM locations 0AH and 0BH contain the values 23H and 01H, respectively. The instruction RETI will leave the stack pointer equal to 09H and return program execution to location 0123H. RETI (PC15-8) ((SP)) (SP) (SP) - 1 (PC7-0) ((SP)) (SP) (SP) - 1 0011 1 2 0010
Example:
Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
193
Instruction Set
RL Function:
A Rotate accumulator left The eight bits in the accumulator are rotated one bit to the left. Bit 7 is rotated into the bit 0 position. No flags are affected. The accumulator holds the value 0C5H (11000101B). The instruction RL A leaves the accumulator holding the value 8BH (10001011B) with the carry unaffected.
Description: Example:
Operation:
RL (An + 1) (An) n = 0-6 (A0) (A7) 0010 1 1 0011
Encoding: Bytes: Cycles:
Semiconductor Group
194
Instruction Set
RLC Function:
A Rotate accumulator left through carry flag The eight bits in the accumulator and the carry flag are together rotated one bit to the left. Bit 7 moves into the carry flag; the original state of the carry flag moves into the bit 0 position. No other flags are affected. The accumulator holds the value 0C5H (11000101B), and the carry is zero. The instruction RLC A
Description:
Example:
leaves the accumulator holding the value 8AH (10001010B) with the carry set. Operation: RLC (An + 1) (An) n = 0-6 (A0) (C) (C) (A7) 0011 1 1 0011
Encoding: Bytes: Cycles:
Semiconductor Group
195
Instruction Set
RR Function:
A Rotate accumulator right The eight bits in the accumulator are rotated one bit to the right. Bit 0 is rotated into the bit 7 position. No flags are affected. The accumulator holds the value 0C5H (11000101B). The instruction RR A leaves the accumulator holding the value 0E2H (11100010B) with the carry unaffected.
Description: Example:
Operation:
RR (An) (An + 1) n = 0-6 (A7) (A0) 0000 1 1 0011
Encoding: Bytes: Cycles:
Semiconductor Group
196
Instruction Set
RRC Function:
A Rotate accumulator right through carry flag The eight bits in the accumulator and the carry flag are together rotated one bit to the right. Bit 0 moves into the carry flag; the original value of the carry flag moves into the bit 7 position. No other flags are affected. The accumulator holds the value 0C5H (11000101B), the carry is zero. The instruction RRC A
Description:
Example:
leaves the accumulator holding the value 62H (01100010B) with the carry set. Operation: RRC (An) (An + 1) n=0-6 (A7) (C) (C) (A0) 0001 1 1 0011
Encoding: Bytes: Cycles:
Semiconductor Group
197
Instruction Set
SETB Function:
Set bit SETB sets the indicated bit to one. SETB can operate on the carry flag or any directiy addressable bit. No other flags are affected. The carry flag is cleared. Output port 1 has been written with the value 34H (00110100B). The instructions SETB SETB C P1.0
Description: Example:
will leave the carry flag set to 1 and change the data output on port 1 to 35H (00110101B). SETB Operation: C SETB (C) 1 1101 1 1 bit SETB (bit) 1 1101 2 1 0010 bit address 0011
Encoding: Bytes: Cycles: SETB Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
198
Instruction Set
SJMP Function:
rel Short jump Program control branches unconditionally to the address indicated. The branch destination is computed by adding the signed displacement in the second instruction byte to the PC, after incrementing the PC twice. Therefore, the range of destinations allowed is from 128 bytes preceding this instruction to 127 bytes following it. The label "RELADR" is assigned to an instruction at program memory location 0123H. The instruction SJMP RELADR will assemble into location 0100H. After the instruction is executed, the PC will contain the value 0123H. Note: Under the above conditions the instruction following SJMP will be at 102H. Therefore, the displacement byte of the instruction will be the relative offset (0123H0102H) = 21H. In other words, an SJMP with a displacement of 0FEH would be a one-instruction infinite loop.
Description:
Example:
Operation:
SJMP (PC) (PC) + 2 (PC) (PC) + rel 1000 2 2 0000 rel. address
Encoding: Bytes: Cycles:
Semiconductor Group
199
Instruction Set
SUBB Function:
A, Subtract with borrow SUBB subtracts the indicated variable and the carry flag together from the accumulator, leaving the result in the accumulator. SUBB sets the carry (borrow) flag if a borrow is needed for bit 7, and clears C otherwise. (If C was set before executing a SUBB instruction, this indicates that a borrow was needed for the previous step in a multiple precision subtraction, so the carry is subtracted from the accumulator along with the source operand). AC is set if a borrow is needed for bit 3, and cleared otherwise. OV is set if a borrow is needed into bit 6 but not into bit 7, or into bit 7 but not bit 6. When subtracting signed integers OV indicates a negative number produced when a negative value is subtracted from a positive value, or a positive result when a positive number is subtracted from a negative number. The source operand allows four addressing modes: register, direct, registerindirect, or immediate.
Description:
Example:
The accumulator holds 0C9H (11001001B), register 2 holds 54H (01010100B), and the carry flag is set. The instruction SUBB A,R2
will leave the value 74H (01110100B) in the accumulator, with the carry flag and AC cleared but OV set. Notice that 0C9H minus 54H is 75H. The difference between this and the above result is due to the (borrow) flag being set before the operation. If the state of the carry is not known before starting a single or multiple-precision subtraction, it should be explicitly cleared by a CLR C instruction. SUBB Operation: Bytes: Cycles: A,Rn SUBB (A) (A) - (C) - (Rn) 1 1
Semiconductor Group
200
Instruction Set
SUBB Operation:
A,direct SUBB (A) (A) - (C) - (direct) 1001 2 1 A, @ Ri SUBB (A) (A) - (C) - ((Ri)) 1001 1 1 A, #data SUBB (A) (A) - (C) - #data 1001 2 1 0100 immediate data 011i 0101 direct address
Encoding: Bytes: Cycles: SUBB Operation:
Encoding: Bytes: Cycles: SUBB Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
201
Instruction Set
SWAP Function:
A Swap nibbles within the accumulator SWAP A interchanges the low and high-order nibbles (four-bit fields) of the accumulator (bits 3-0 and bits 7-4). The operation can also be thought of as a fourbit rotate instruction. No flags are affected. The accumulator holds the value 0C5H (11000101B). The instruction SWAP A leaves the accumulator holding the value 5CH (01011100B).
Description:
Example:
Operation:
SWAP (A3-0) (A7-4), (A7-4) (A3-0) 1100 1 1 0100
Encoding: Bytes: Cycles:
Semiconductor Group
202
Instruction Set
XCH Function:
A, Exchange accumulator with byte variable XCH loads the accumulator with the contents of the indicated variable, at the same time writing the original accumulator contents to the indicated variable. The source/ destination operand can use register, direct, or register-indirect addressing. R0 contains the address 20H. The accumulator holds the value 3FH (00111111B). Internal RAM location 20H holds the value 75H (01110101B). The instruction XCH A, @R0 will leave RAM location 20H holding the value 3FH (00111111 B) and 75H (01110101B) in the accumulator.
Description:
Example:
XCH Operation:
A,Rn XCH (A) (Rn) 1100 1 1 A,direct XCH (A) (direct) 1100 2 1 0101 direct address 1rrr
Encoding: Bytes: Cycles: XCH Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
203
Instruction Set
XCH Operation:
A, @ Ri XCH (A) ((Ri)) 1100 1 1 011i
Encoding: Bytes: Cycles:
Semiconductor Group
204
Instruction Set
XCHD Function:
A,@Ri Exchange digit XCHD exchanges the low-order nibble of the accumulator (bits 3-0, generally representing a hexadecimal or BCD digit), with that of the internal RAM location indirectly addressed by the specified register. The high-order nibbles (bits 7-4) of each register are not affected. No flags are affected. R0 contains the address 20H. The accumulator holds the value 36H (00110110B). Internal RAM location 20H holds the value 75H (01110101B). The instruction XCHD A, @ R0 will leave RAM location 20H holding the value 76H (01110110B) and 35H (00110101B) in the accumulator.
Description:
Example:
Operation:
XCHD (A3-0)

((Ri)3-0) 011i
Encoding: Bytes: Cycles:
1101 1 1
Semiconductor Group
205
Instruction Set
XRL Function:

, Logical Exclusive OR for byte variables XRL performs the bitwise logical Exclusive OR operation between the indicated variables, storing the results in the destination. No flags are affected. The two operands allow six addressing mode combinations. When the destination is the accumulator, the source can use register, direct, register-indirect, or immediate addressing; when the destination is a direct address, the source can be accumulator or immediate data. Note: When this instruction is used to modify an output port, the value used as the original port data will be read from the output data latch, not the input pins.
Description:
Example:
If the accumulator holds 0C3H (11000011B) and register 0 holds 0AAH (10101010B) then the instruction XRL A,R0
will leave the accumulator holding the value 69H (01101001B). When the destination is a directly addressed byte, this instruction can complement combinations of bits in any RAM location or hardware register. The pattern of bits to be complemented is then determined by a mask byte, either a constant contained in the instruction or a variable computed in the accumulator at run-time. The instruction XRL P1,#00110001B
will complement bits 5, 4, and 0 of output port 1. XRL Operation: A,Rn XRL2 (A) (A) v (Rn) 0110 1 1 1rrr
Encoding: Bytes: Cycles:
Semiconductor Group
206
Instruction Set
XRL Operation:
A,direct XRL (A) (A) v (direct) 0110 2 1 A, @ Ri XRL (A) (A) v ((Ri)) 0110 1 1 A, #data XRL (A) (A) v #data 0110 2 1 direct,A XRL (direct) (direct) v (A) 0110 2 1 0010 direct address 0100 immediate data 011i 0101 direct address
Encoding: Bytes: Cycles: XRL Operation:
Encoding: Bytes: Cycles: XRL Operation:
Encoding: Bytes: Cycles: XRL Operation:
Encoding: Bytes: Cycles:
Semiconductor Group
207
Instruction Set
XRL Operation:
direct, #data XRL (direct) (direct) v #data 0110 3 2 0011 direct address immediate data
Encoding: Bytes: Cycles:
Semiconductor Group
208
Instruction Set
Instruction Set Summary Mnemonic Arithmetic Operations ADD ADD ADD ADD A,Rn A,direct A, @Ri A,#data Add register to accumulator Add direct byte to accumulator Add indirect RAM to accumulator Add immediate data to accumulator Add register to accumulator with carry flag Add direct byte to A with carry flag Add indirect RAM to A with carry flag Add immediate data to A with carry flag Subtract register from A with borrow Subtract direct byte from A with borrow Subtract indirect RAM from A with borrow Subtract immediate data from A with borrow Increment accumulator Increment register Increment direct byte Increment indirect RAM Decrement accumulator Decrement register Decrement direct byte Decrement indirect RAM Increment data pointer Multiply A and B Divide A by B Decimal adjust accumulator 1 2 1 2 1 2 1 2 1 2 1 2 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 4 1 Description Byte Cycle
ADDC A,Rn ADDC A,direct ADDC A, @Ri ADDC A, #data SUBB SUBB SUBB SUBB INC INC INC INC DEC DEC DEC DEC INC MUL DIV DA A,Rn A,direct A,@Ri A,#data A Rn direct @Ri A Rn direct @Ri DPTR AB AB A
Semiconductor Group
209
Instruction Set
Instruction Set Summary (cont'd) Mnemonic Logic Operations ANL ANL ANL ANL ANL ANL ORL ORL ORL ORL ORL ORL XRL XRL XRL XRL XRL XRL CLR CPL RL RLC RR RRC A,Rn A,direct A,@Ri A,#data direct,A direct,#data A,Rn A,direct A,@Ri A,#data direct,A direct,#data A,Rn A direct A,@Ri A,#data direct,A direct,#data A A A A A A AND register to accumulator AND direct byte to accumulator AND indirect RAM to accumulator AND immediate data to accumulator AND accumulator to direct byte AND immediate data to direct byte OR register to accumulator OR direct byte to accumulator OR indirect RAM to accumulator OR immediate data to accumulator OR accumulator to direct byte OR immediate data to direct byte Exclusive OR register to accumulator Exclusive OR direct byte to accumulator Exclusive OR indirect RAM to accumulator Exclusive OR immediate data to accumulator Exclusive OR accumulator to direct byte Exclusive OR immediate data to direct byte Clear accumulator Complement accumulator Rotate accumulator left Rotate accumulator left through carry Rotate accumulator right Rotate accumulator right through carry Swap nibbles within the accumulator 1 2 1 2 2 3 1 2 1 2 2 3 1 2 1 2 2 3 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 1 1 1 1 1 2 1 1 1 1 1 1 1 Description Byte Cycle
SWAP A
Semiconductor Group
210
Instruction Set
Instruction Set Summary (cont'd) Mnemonic Data Transfer MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV A,Rn A,direct A,@Ri A,#data Rn,A Rn,direct Rn,#data direct,A direct,Rn direct,direct direct,@Ri direct,#data @Ri,A @Ri,direct @Ri, #data
*)
Description
Byte
Cycle
Move register to accumulator Move direct byte to accumulator Move indirect RAM to accumulator Move immediate data to accumulator Move accumulator to register Move direct byte to register Move immediate data to register Move accumulator to direct byte Move register to direct byte Move direct byte to direct byte Move indirect RAM to direct byte Move immediate data to direct byte Move accumulator to indirect RAM Move direct byte to indirect RAM Move immediate data to indirect RAM Move code byte relative to DPTR to accumulator Move code byte relative to PC to accumulator Move external RAM (8-bit addr.) to A Move external RAM (16-bit addr.) to A Move A to external RAM (8-bit addr.) Move A to external RAM (16-bit addr.) Push direct byte onto stack Pop direct byte from stack Exchange register with accumulator Exchange direct byte with accumulator Exchange indirect RAM with accumulator Exchange low-order nibble indir. RAM with A
1 2 1 2 1 2 2 2 2 3 2 3 1 2 2 3 1 1 1 1 1 1 2 2 1 2 1 1
1 1 1 1 1 2 1 1 2 2 2 2 1 2 1 2 2 2 2 2 2 2 2 2 1 1 1 1
DPTR, #data16 Load data pointer with a 16-bit constant
MOVC A,@A + DPTR MOVC A,@A + PC MOVX A,@Ri MOVX A,@DPTR MOVX @Ri,A MOVX @DPTR,A PUSH direct POP XCH XCH XCH direct A,Rn A,direct A,@Ri
XCHD A,@Ri
*) MOV A,ACC is not a valid instruction
Semiconductor Group
211
Instruction Set
Instruction Set Summary (cont'd) Mnemonic Description Byte Cycle
Boolean Variable Manipulation CLR CLR SETB SETB CPL CPL ANL ANL ORL ORL MOV MOV C bit C bit C bit C,bit C,/bit C,bit C,/bit C,bit bit,C Clear carry flag Clear direct bit Set carry flag Set direct bit Complement carry flag Complement direct bit AND direct bit to carry flag AND complement of direct bit to carry OR direct bit to carry flag OR complement of direct bit to carry Move direct bit to carry flag Move carry flag to direct bit 1 2 1 2 1 2 2 2 2 2 2 2 1 1 1 1 1 1 2 2 2 2 1 2
Program and Machine Control ACALL addr11 LCALL addr16 RET RETI AJMP LJMP SJMP JMP JZ JNZ JC JNC JB JNB JBC CJNE addr11 addr16 rel @A + DPTR rel rel rel rel bit,rel bit,rel bit,rel A,direct,rel Absolute subroutine call Long subroutine call Return from subroutine Return from interrupt Absolute jump Long iump Short jump (relative addr.) Jump indirect relative to the DPTR Jump if accumulator is zero Jump if accumulator is not zero Jump if carry flag is set Jump if carry flag is not set Jump if direct bit is set Jump if direct bit is not set Jump if direct bit is set and clear bit Compare direct byte to A and jump if not equal 2 3 1 1 2 3 2 1 2 2 2 2 3 3 3 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
Semiconductor Group
212
Instruction Set
Instruction Set Summary (cont'd) Mnemonic Description Byte Cycle
Program and Machine Control (cont'd) CJNE CJNE CJNE DJNZ DJNZ NOP A,#data,rel Rn,#data rel @Ri,#data,rel Rn,rel direct,rel Compare immediate to A and jump if not equal Compare immed. to reg. and jump if not equal Compare immed. to ind. and jump if not equal Decrement register and jump if not zero Decrement direct byte and jump if not zero No operation 3 3 3 2 3 1 2 2 2 2 2 1
Semiconductor Group
213
High-Performance 8-Bit CMOS Single-Chip Microcontroller
Preliminary SAB 80C515/80C515-16 SAB 80C535/80C535-16
q q q q q q q q
SAB 80C515/80C535
CMOS microcontroller with factory mask-programmable ROM CMOS microcontroller for external ROM
q q q q q q q q q q
q
8 K x 8 ROM (SAB 80C515 only) 256 x 8 RAM Six 8-bit I/O ports, one input port for digital or analog input Three 16-bit timer/counters Highly flexible reload, capture, compare capabilities Full-duplex serial channel Twelve interrupt vectors, four priority levels 8-bit A/D converter with 8 multiplexed inputs and programmable internal reference voltages 16-bit watchdog timer
Boolean processor Most instructions execute in 1 s (750 ns) 4 s (3 s) multiply and divide External memory expandable up to 128 Kbytes Backwardly compatible with SAB 8051 Functionally compatible with SAB 80515 Idle and power-down mode Plastic leaded chip carrier package: P-LCC-68 Plastic Metric Quad Flat Package P-MQFP-80 Two temperature ranges available: 0 to 70 C (for 12, 16, 20 MHz) - 40 to 85 C (for 12, 16 MHz)
The SAB 80C515/80C535 is a powerful member of the Siemens SAB 8051 family of 8-bit microcontrollers. It is designed in Siemens ACMOS technology and is functionally compatible with the SAB 80515/80535 devices designed in MYMOS technology. The SAB 80C515/80C535 is a stand-alone, high-performance single-chip microcontroller based on the SAB 8051/80C51 architecture. While maintaining all the SAB 80C51 operating characteristics, the SAB 80C515/80C535 incorporates several enhancements which significantly increase design flexibility and overall system performance. In addition, the low-power properties of Siemens ACMOS technology allow applications where power consumption and dissipation are critical. Furthermore, the SAB 80C515/80C535 has two software-selectable modes of reduced activity for further power reduction: idle and powerdown mode. The SAB 80C535 is identical with the SAB 80C515 except that it lacks the on-chip program memory. The SAB 80C515/80C535 is supplied in a 68-pin plastic leaded chip carrier package (P-LCC-68) or in a plastic metric quad flat package (P-MQFP-80). There are versions for 12, 16 and 20 MHz operation and for extended temperature ranges - 40 to 85 C. Versions for extended temperature range - 40 to + 110 C are available on request.
Semiconductor Group
214
Device Specifications
Semiconductor Group
215
Device Specifications
Ordering Information Type SAB 80C515-N SAB 80C535-N SAB 80C515-N-T40/85 Ordering Code Package Description 8-Bit CMOS Microcontroller with mask-programmable ROM, 12 MHz for external memory, 12 MHz with mask-programmable ROM, 12 MHz ext. temperature - 40 to + 85 C for external memory, 12 MHz ext. temperature - 40 to + 85 C with mask-programmable ROM, 16 MHz for external memory, 16 MHz for external memory, 16 MHz ext. temperature - 40 to + 85 C for external memory, 20 MHz for external memory, 12 MHz with mask-programmable ROM, 12 MHz for external memory, 12 MHz ext. temperature - 40 to + 85 C with mask-programmable ROM, 12 MHz ext. temperature - 40 to + 85 C
Q 67120-DXXXX P-LCC-68 Q 67120-C0508 P-LCC-68 Q 67120-DXXXX P-LCC-68
SAB 80C535-N-T40/85 SAB 80C515-16-N SAB 80C535-16-N SAB 80C535-16-NT40/85 SAB 80C535-20-N SAB 80C535-M SAB 80C515-M SAB 80C535-M-T40/85 SAB 80C515-M-T40/85
Q 67120-C0510
P-LCC-68
Q 67120-DXXXX P-LCC-68 Q 67120-C0509 Q 67120-C0562 Q 67120-C0778 Q67120-C0857 Q67120-DXXXX Q67120-C0937 Q67120-DXXXX P-LCC-68 P-LCC-68 P-LCC-68 P-MQFP-80 P-MQFP-80 P-MQFP-80 P-MQFP-80
Notes:
Versions for extended temperature range - 40 to + 110 C on request. The ordering number of ROM types (DXXXX extension) is defined after program release (verification) of the customer.
Semiconductor Group
216
Device Specifications
Pin Configuration (P-LCC-68)
Semiconductor Group
217
Device Specifications
RESET N.C. VAREF VAGND P6.7 / AIN7 P6.6 / AIN6 P6.5 / AIN5 P6.4 / AIN4 P6.3 / AIN3 P6.2 / AIN2 P6.1 / AIN1 P6.0 / AIN0 N.C. N.C. P3.0 / RXD0 P3.1 / TXD0 P3.2 / INT0 P3.3 / INT1 P3.4 / T0 P3.5 / T1
80 1
P4.7 P4.6 P4.5 P4.4 P4.3 PE P4.2 P4.1 P4.0 N.C. N.C. VCC N.C. P5.0 P5.1 P5.2 P5.3 P5.4 P5.5 P5.6
75 70 65 61 60 5 55
SAB 80C535 / 80C515
10
P-MQFP-80 Package
50
15 45
20 21
25
30
35
41 40
P5.7 P0.7 / AD7 P0.6 / AD6 P0.5 / AD5 P0.4 / AD4 P0.3 / AD3 P0.2 / AD2 P0.1 / AD1 P0.0 / AD0 N.C. N.C. EA ALE PSEN N.C. P2.7 / A15 P2.6 / A14 P2.5 / A13 P2.4 / A12 P2.3 / A11
N.C. pins must not be connected.
Pin Configuration (P-MQFP-80)
Semiconductor Group
P3.6 / WR P3.7 / RD N.C. P1.7 / T2 P1.6 / CLKOUT P1.5 / T2EX P1.4 / INT2 P1.3 / INT6 / CC3 P1.2 / INT5 / CC2 P1.1 / INT4 / CC1 P1.0 / INT3 / CC0 N.C. VCC VSS N.C. XTAL2 XTAL1 P2.0 / A8 P2.1 / A9 P2.2 / A10
218
Device Specifications
Logic Symbol
Semiconductor Group
219
Device Specifications
Pin Definitions and Functions Symbol Pin Pin Input (I) Function P-LCC-68 P-MQFP-80 Output (O) 72-74, 76-80 I/O Port 4 is an 8-bit bidirectional I/O port with internal pullup resistors. Port 4 pins that have 1's written to them are pulled high by the internal pullup resistors, and in that state can be used as inputs. As inputs, port 4 pins being externally pulled low will source current (I I L, in the DC characteristics) because of the internal pullup resistors. Power saving mode enable A low level on this pin enables the use of the power saving modes (idle mode and power-down mode). When PE is held on high level it is impossible to enter the power saving modes. Reset pin A low level on this pin for the duration of two machine cycles while the oscillator is running resets the SAB 80C515. A small internal pullup resistor permits power-on reset using only a capacitor connected to V SS. Reference voltage for the A/D converter Reference ground for the A/D converter Port 6 is an 8-bit undirectional input port. Port pins can be used for digital input if voltage levels simultaneously meet the specifications for high/low input voltages and for the eight multiplexed analog inputs of the A/D converter.
P4.0-P4.7 1-3, 5-9
PE
4
75
I
RESET
10
1
I
V AREF VAGND
11 12
3 4 5-12
P6.7-P6.0 13-20
Semiconductor Group
220
Device Specifications
Pin Definitions and Functions (cont'd) Symbol Pin Pin Input (I) Function P-LCC-68 P-MQFP-80 Output (O) 15-22 I/O Port 3 is an 8-bit bidirectional I/O port with internal pullup resistors. Port 3 pins that have1's written to them are pulled high by the internal pullup resistors, and in that state can be used as inputs. As inputs, port 3 pins being externally pulled low will source current (IIL, in the DC characteristics) because of the internal pullup resistors. Port 3 also contains the interrupt, timer, serial port and external memory strobe pins that are used by various options. The output latch corresponding to a secondary function must be programmed to a one (1) for that function to operate. The secondary functions are assigned to the pins of port 3, as follows: - RxD (P3.0): serial port's receiver data input (asynchronous) or data input/ output (synchronous) - TxD (P3.1): serial port's transmitter data output (asynchronous) or clock output (synchronous) - INT0 (P3.2): interrupt 0 input/timer 0 gate control input - INT1 (P3.3): interrupt 1 input/timer 1 gate control input - T0 (P3.4): counter 0 input - T1 (P3.5): counter 1 input - WR (P3.6): the write control signal latches the data byte from port 0 into the external data memory - RD (P3.7): the read control signal enables the external data memory to port 0
P3.0-P3.7 21-28
Semiconductor Group
221
Device Specifications
Pin Definitions and Functions (cont'd) Symbol Pin Pin Input (I) Function P-LCC-68 P-MQFP-80 Output (O) 24-31 I/O Port 1 is an 8-bit bidirectional I/O port with internal pullup resistors. Port 1 pins that have 1's written to them are pulled high by the internal pullup resistors, and in that state can be used as inputs. As inputs, port 1 pins being externally pulled low will source current (I I L in the DC characteristics) because of the internal pullup resistors. The port is used for the low-order address byte during program verification. Port 1 also contains the interrupt, timer, clock, capture and compare pins that are used by various options. The output latch corresponding to a secondary function must be programmed to a one (1) for that function to operate (except when used for the compare functions). The secondary functions are assigned to the port 1 pins as follows: - INT3/CC0 (P1.0): interrupt 3 input/ compare 0 output/capture 0 input - INT4/CC1 (P1.1): interrupt 4 input/ compare 1 output/capture 1 input - INT5/CC2 (P1.2): interrupt 5 input/ compare 2 output/capture 2 input - INT6/CC3 (P1.3): interrupt 6 input/ compare 3 output/capture 3 input - INT2 (P1.4): interrupt 2 input - T2EX (P1.5): timer 2 external reload trigger input - CLKOUT (P1.6): system clock output - T2 (P1.7): counter 2 input
P1.7-P1.0 29-36
Semiconductor Group
222
Device Specifications
Pin Definitions and Functions (cont'd) Symbol XTAL2 XTAL1 Pin Pin Input (I) Function P-LCC-68 P-MQFP-80 Output (O) 39 40 36 37 XTAL2 Input to the inverting oscillator amplifier and input to the internal clock generator circuits. XTAL1 Output of the inverting oscillator amplifier. To drive the device from an external clock source, XTAL2 should be driven, while XTAL1 is left unconnected. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is divided down by a divide-by-two flip-flop. Minimum and maximum high and low times and rise/fall times specified in the AC characteristics must be observed. I/O Port 2 is an 8-bit bidirectional I/O port with internal pullup resistors. Port 2 pins that have 1's written to them are pulled high by the internal pullup resistors, and in that state can be used as inputs. As inputs, port 2 pins being externally pulled low will source current (I I L, in the DC characteristics) because of the internal pullup resistors. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX@DPTR). In this application it uses strong internal pullup resistors when issuing 1's. During accesses to external data memory that use 8-bit addresses (MOVX@Ri), port 2 issues the contents of the P2 special function register.
P2.0-P2.7 41-48
38-45
Semiconductor Group
223
Device Specifications
Pin Definitions and Functions (cont'd) Symbol PSEN Pin Pin Input (I) Function P-LCC-68 P-MQFP-80 Output (O) 49 47 O The Program store enable output is a control signal that enables the external program memory to the bus during external fetch operations. It is activated every six oscillator periods, except during external data memory accesses. The signal remains high during internal program execution. The Address latch enable output is used for latching the address into external memory during normal operation. It is activated every six oscillator periods, except during an external data memory access. External access enable When held high, the SAB 80C515 executes instructions from the internal ROM as long as the PC is less than 8192. When held low, the SAB 80C515 fetches all instructions from external program memory. For the SAB 80C535 this pin must be tied low. Port 0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1's written to them float, and in that state can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application it uses strong internal pullup resistors when issuing 1's. Port 0 also outputs the code bytes during program verification in the SAB 80C515. External pullup resistors are required during program verification.
ALE
50
48
O
EA
51
49
I
P0.0-P0.7 52-59
52-59
I/O
Semiconductor Group
224
Device Specifications
Pin Definitions and Functions (cont'd) Symbol Pin Pin Input (I) Function P-LCC-68 P-MQFP-80 Output (O) 60-67 I/O Port 5 is an 8-bit bidirectional I/O port with internal pullup resistors. Port 5 pins that have 1's written to them are pulled high by the internal pullup resistors, and in that state can be used as inputs. As inputs, port 5 pins being externally pulled low will source current (I IL in the DC characteristics) because of the internal pullup resistors. Supply voltage during normal, idle, and power-down operation. Internally connected to pin 68. Ground (0 V) Supply voltage during normal, idle, and power-down operation. Internally connected to pin 37. Not connected These pins of the P-MQFP-80 package must not be connected
P5.7-P5.0 60-67
VCC
37
33
-
VSS VCC
38 68
34 69
- -
N. C.
-
2, 13, 14, 23, 32, 35, 46, 50, 51, 68, 70, 71
-
Semiconductor Group
225
Device Specifications
Figure 1 Block Diagram Semiconductor Group 226
Device Specifications
Functional Description The members of the SAB 80515 family of microcontrollers are: - SAB 80C515: Microcontroller, designed in Siemens ACMOS technology, with 8 Kbyte factory mask-programmable ROM - SAB 80C535: ROM-less version of the SAB 80C515 - SAB 80515: Microcontroller, designed in Siemens MYMOS technology, with 8 Kbyte factory mask-programmable ROM - SAB 80535: ROM-less version of the SAB 80515 The SAB 80C535 is identical to the SAB 80C515, except that it lacks the on-chip ROM. In this data sheet the term "SAB 80C515" is used to refer to both the SAB 80C515 and SAB 80C535, unless otherwise noted. Principles of Architecture The architecture of the SAB 80C515 is based on the SAB 8051/SAB 80C51 microcontroller family. The following features of the SAB 80C515 are fully compatible with the SAB 80C51 features: - - - - - - Instruction set External memory expansion interface (port 0 and port 2) Full-duplex serial port Timer/counter 0 and 1 Alternate functions on port 3 The lower 128 bytes of internal RAM and the lower 4 Kbytes of internal ROM
The SAB 80C515 additionally contains 128 bytes of internal RAM and 4 Kbytes of internal ROM, which results in a total of 256 bytes of RAM and 8 Kbytes of ROM on-chip. The SAB 80C515 has a new 16-bit timer/counter with a 2:1 prescaler, reload mode, compare and capture capability. It also contains at 16-bit watchdog timer, an 8-bit A/D converter with programmable reference voltages, two additional quasi-bidirectional 8-bit ports, one 8-bit input port for analog or digital signals, and a programmable clock output (f OSC/12). Furthermore, the SAB 80C515 has a powerful interrupt structure with 12 vectors and 4 programmable priority levels. Figure 1 shows a block diagram of the SAB 80C515.
Semiconductor Group
227
Device Specifications
CPU The SAB 80C515 is efficient both as a controller and as an arithmetic processor. It has extensive facilities for binary and BCD arithmetic and excels in its bit-handling capabilities. Efficient use of program memory results from an instruction set consisting of 44 % one-byte, 41 % two-byte, and 15 % three-byte instructions. With a 12 MHz crystal, 58 % of the instructions execute in 1.0 s. Memory Organization The SAB 80C515 manipulates operands in the four memory address spaces described below: Figure 1 illustrates the memory address spaces of the SAB 80C515. Program Memory The SAB 80C515 has 8 Kbyte of on-chip ROM, while the SAB 80C535 has no internal ROM. The program memory can be externally expanded up to 64 Kbytes. If the EA pin is held high, the SAB 80C515 executes out of internal ROM unless the address exceeds 1FFFH. Locations 2000H through 0FFFFH are then fetched from the external program memory. If the EA pin is held now, the SAB 80C515 fetches all instructions from the external program memory. Since the SAB 80C535 has no internal ROM, pin EA must be tied low when using this component. Data Memory The data memory address space consists of an internal and an external memory space. The internal data memory is divided into three physically separate and distinct blocks: the lower 128 bytes of RAM, the upper 128 bytes of RAM, and the 128 byte special function register (SRF) area. While the upper 128 bytes of data memory and the SFR area share the same address locations, they are accessed through different addressing modes. The lower 128 bytes of data memory can be accessed through direct or register indirect addressing; the upper 128 bytes of RAM can be accessed through register indirect addressing; the special function registers are accessible through direct addressing. Four 8-register banks, each bank consisting of eight 8-bit multi-purpose registers, occupy locations 0 through 1FH in the lower RAM area. The next 16 bytes, locations 20H through 2FH, contain 128 directly addressable bit locations. The stack can be located anywhere in the internal data memory address space, and the stack depth can be expanded up to 256 bytes. The external data memory can be expanded up to 64 Kbytes and can be accessed by instructions that use a 16-bit or an 8-bit address.
Semiconductor Group
228
Device Specifications
Figure 2 Memory Address Spaces
Semiconductor Group
229
Device Specifications
Special Function Registers All registers, except the program counter and the four general purpose register banks, reside in the special function register area. The special function registers include arithmetic registers, pointers, and registers that provide an interface between the CPU and the on-chip peripherals. There are also 128 directly addressable bits within the SFR area. All special function registers are listed in table 1 and table 2. In table 1 they are organized in numeric order of their addresses. In table 3 they are organized in groups which refer to the functional blocks of the SAB 80C515. Table 1: Special Function Register Address 80H 81H 82H 83H 84H 85H 86H 87H 88H 89H 8AH 8BH 8CH 8DH 8EH 8FH 90H 91H 92H 93H 94H 95H 96H 97H
1) 2)
Register P0 1) SP DPL DPH reserved reserved reserved PCON TCON 1) TMOD TL0 TL1 TH0 TH1 reserved reserved P1 1) reserved reserved reserved reserved reserved reserved reserved
Contents after Reset 0FFH 07H 00H 00H XXH 2) XXH 2) XXH 2) 000X 0000B 2) 00H 00H 00H 00H 00H 00H XXH 2) XXH 2) 0FFH XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2)
Address 98H 99H 9AH 9BH 9CH 9DH 9EH 9FH A0H A1H A2H A3H A4H A5H A6H A7H A8H A9H AAH ABH ACH ADH AEH AFH
Register SCON 1) SBUF reserved reserved reserved reserved reserved reserved P2 1) reserved reserved reserved reserved reserved reserved reserved IEN0 1) IP0 reserved reserved reserved reserved reserved reserved
Contents after Reset 00H XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) 0FFH XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) 00H X000 0000B 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2)
Bit-addressable Special Function Register X means that the value is indeterminate and the location is reserved
Semiconductor Group
230
Device Specifications
Table 1:Special Function Register (cont'd) Address B0H B1H B2H B3H B4H B5H B6H B7H B8H B9H BAH BBH BCH BDH BSH BFH C0H C1H C2H C3H C4H C5H C6H C7H C8H C9H CAH CBH CCH CDH CEH CFH
1) 2)
Register P3 1) reserved reserved reserved reserved reserved reserved reserved IEN1 1) IP1 reserved reserved reserved reserved reserved reserved IRCON 1) CCEN CCL1 CCH1 CCL2 CCH2 CCL3 CCH3 T2CON 1) reserved CRCL CRCH TL2 TH2 reserved reserved
Contents after Reset 0FFH XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) 00H XX00 0000B 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) 00H 00H 00H 00H 00H 00H 00H 00H 00H XXH 2) 00H 00H 00H 00H XXH 2) XXH 2)
Address D0H D1H D2H D3H D4H D5H D6H D7H D8H D9H DAH DBH DCH DDH DEH DFH E0H E1H E2H E3H E4H E5H E6H E7H E8H E9H EAH EBH ECH EDH EEH EFH
Register PSW 1) reserved reserved reserved reserved reserved reserved reserved ADCON1) ADDAT DAPR P6 reserved reserved reserved reserved ACC 1) reserved reserved reserved reserved reserved reserved reserved P4 1) reserved reserved reserved reserved reserved reserved reserved
Contents after Reset 00H XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) 00X0 0000B 00H 00H XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) 00H XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) 0FFH XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2)
2)
Bit-addressable Special Function Register X means that the value is indeterminate and the location is reserved
Semiconductor Group
231
Device Specifications
Table 1:Special Function Register (cont'd) Address F0H F1H F2H F3H F4H F5H F6H F7H
1) 2)
Register B 1) reserved reserved reserved reserved reserved reserved reserved
Contents after Reset 00H XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2)
Address F8H F9H FAH FBH FCH FDH FEH FFH
Register P5 1) reserved reserved reserved reserved reserved reserved reserved
Contents after Reset 0FFH XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2) XXH 2)
Bit-addressable Special Function Register X means that the value is indeterminate and the location is reserved
Semiconductor Group
232
Device Specifications
Table 2: Special Function Registers - Functional Blocks Block CPU Symbol ACC B DPH DPL PSW SP ADCON ADDAT DAPR EN0 IEN1 IP0 IP1 IRCON TCON 2) T2CON 2) CCEN CCH1 CCH2 CCH3 CCL1 CCL2 CCL3 CRCH CRCL TH2 TL2 T2CON Name Accumulator B-Register Data Pointer, High Byte Data Pointer, Low Byte Program Status Word Register Stack Pointer A/D Converter Control Register A/D Converter Data Register D/A Converter Program Register Interrupt Enable Register 0 Interrupt Enable Register 1 Interrupt Priority Register 0 Interrupt Priority Register 1 Interrupt Request Control Register Timer Control Register Timer 2 Control Register Comp./Capture Enable Reg. Comp./Capture Reg. 1, High Byte Comp./Capture Reg. 2, High Byte Comp./Capture Reg. 3, High Byte Comp./Capture Reg. 1, Low Byte Comp./Capture Reg. 2, Low Byte Comp./Capture Reg. 3, Low Byte Com./Rel./Capt. Reg. High Byte Com./Rel./Capt. Reg. Low Byte Timer 2, High Byte Timer 2, Low Byte Timer 2 Control Register Address 0E0H 1) 0F0H 1) 83H 82H 0D0H 1) 81H 0D8H 1) 0D9H 0DAH 0A8H 1) 0B8H 1) 0A9H 0B9H 0C0H 1) 88H 1) 0C8H 1) 0C1H 0C3H 0C5H 0C7H 0C2H 0C4H 0C6H 0CBH 0CAH 0CDH 0CCH 0C8H 1) Contents after Reset 00H 00H 00H 00H 00H 07H 00X0 0000B 00H 00H
2)
A/DConverter Interrupt System
00H 00H 00H X000 0000B 2) XX00 0000B 3) 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H
Compare/ CaptureUnit (CCU)
1) 2)
3)
Bit-addressable special function registers This special function register is listed repeatedly since some bits of it also belong to other functional blocks. X means that the value is indeterminate and the location is reserved
Semiconductor Group
233
Device Specifications
Table 2: Special Function Registers- Functional Blocks (cont'd) Block Ports Symbol P0 P1 P2 P3 P4 P5 P6 PCON ADCON 2) PCON 2) SBUF SCON TCON TH0 TH1 TL0 TL1 TMOD IEN0 2) IEN1 2) IP0 2) IP1 2) Name Port 0 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6, Analog/Digital Input Power Control Register A/D Converter Control Reg. Power Control Register Serial Channel Buffer Reg. Serial Channel Control Reg. Timer Control Register Timer 0, High Byte Timer 1, High Byte Timer 0, Low Byte Timer 1, Low Byte Timer Mode Register Interrupt Enable Register 0 Interrupt Enable Register 1 Interrupt Priority Register 0 Interrupt Priority Register 1 Address 80H 1) 90H 1) 0A0H 1) 0B0H 1) 0E8H 1) 0F8H 1) 0DBH 87H 0D8H 1) 87H 99H 98H 1) 88H 1) 8CH 8DH 8AH 8BH 89H 0A8H 1) 0B8H 1) 0A9H 0B9H Contents after Reset 0FFH 0FFH 0FFH 0FFH 0FFH 0FFH 000X 0000B 2) 00X0 0000B 2) 000X 0000B 2) 0XXH 3) 00H 00H 00H 00H 00H 00H 00H 00H 00H X000 0000B 2) XX00 0000B 3)
Pow.Sav.M odes Serial Channels
Timer 0/ Timer 1
Watchdog
1) 2)
3)
Bit-addressable special function registers This special function register is listed repeatedly since some bits of it also belong to other functional blocks. X means that the value is indeterminate and the location is reserved
Semiconductor Group
234
Device Specifications
I/O Ports The SAB 80C515 has six 8-bit I/O ports and one 8-bit input port. Port 0 is an open-drain bidirectional I/O port, while ports 1 to 5 are quasi-bidirectional I/O ports with internal pullup resistors. That means, when configured as inputs, ports 1 to 5 will be pulled high and will source current when externally pulled low. Port 0 will float when configured as input. Port 0 and port 2 can be used to expand the program and data memory externally. During an access to external memory, port 0 emits the low-order address byte and reads/writes the data byte, while port 2 emits the high-order address byte. In this function, port 0 is not an open-drain port, but uses a strong internal pullup FET. Ports 1 and 3 are provided for several alternate functions, as listed below: Port P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 Symbol INT3/CC0 INT4/CC1 INT5/CC2 INT6/CC3 INT2 T2EX CLKOUT T2 RxD TxD INT0 INT1 T0 T1 WR RD Function External interrupt 3 input, compare 0 output, capture 0 input External interrupt 4 input, compare 1 output, capture 1 input External interrupt 5 input, compare 2 output, capture 2 input External interrupt 6 input, compare 3 output, capture 3 input External interrupt 2 input Timer 2 external reload trigger input System clock output Timer 2 external count or gate input Serial port's receiver data input (asynchronous) or data input/output (synchronous) Serial port's transmitter data output (asynchronous) or clock output (synchronous) External interrupt 0 input, timer 0 gate control External interrupt 1 input, timer 1 gate control Timer 0 external counter input Timer 1 external counter input External data memory write strobe External data memory read strobe
The SAB 80C515 has dual-purpose input port. As the ANx lines in the SAB 80515 (NMOS version), the eight port lines at port 6 can be used as analog inputs. But if the input voltages at port 6 meet the specified digital input levels (VIL an d VIH), the port can also be used as digital input port. Reading the special function register P6 allows the user to input the digital values currently applied to the port pins. It is not necessary to select these modes by software; the voltages applied at port 6 pins can be converted to digital values using the A/D converter and at the same time the pins can be read via SFR P6. It must be noted, however, that the results in port P6 bits will be indeterminate if the levels at the corresponding pins are not within their respective V IL/ VIH specifications. Furthermore, it is not possible to use port P6 as output lines. Special function register P6 is located at address 0DBH.
Semiconductor Group
235
Device Specifications
Timer/Counters The SAB 80C515 contains three 16-bit timers/counters which are useful in many applications for timing and counting. The input clock for each timer/counter is 1/12 of the oscillator frequency in the timer operation or can be taken from an external clock source for the counter operation (maximum count rate is 1/24 of the oscillator frequency). - Timer/Counter 0 and 1 These timers/counters can operate in four modes: Mode 0: 8-bit timer/counter with 32:1 prescaler Mode 1: 16-bit timer/counter Mode 2: 8-bit timer/counter with 8-bit auto-reload Mode 3: Timer/counter 0 is configured as one 8-bit timer/counter and one 8-bit timer; Timer/counter 1 in this mode holds its count. External inputs INT0 and INT1 can be programmed to function as a gate for timer/counters 0 and 1 to facilitate pulse width measurements. - Timer/Counter 2 Timer/counter 2 of the SAB 80C515 is a 16-bit timer/counter with several additional features. It offers a 2:1 prescaler, a selectable gate function, and compare, capture and reload functions. Corresponding to the 16-bit timer register there are four 16-bit capture/compare registers, one of them can be used to perform a 16-bit reload on a timer overflow or external event. Each of these registers corresponds to a pin of port 1 for capture input/compare output. Figure 3 shows a block diagram of timer/counter 2. Reload A 16-bit reload can be performed with the 16-bit CRC register consisting of CRCL and CRCH. There are two modes from which to select: Mode 0: Reload is caused by a timer 2 overflow (auto-reload). Mode 1: Reload is caused in response to a negative transition at pin T2EX (P1.5), which can also request an interrupt. Capture This feature permits saving the actual timer/counter contents into a selected register upon an external event or a software write operation. Two modes are provided to latch the current 16-bit value in timer 2 registers TL2 and TH2 into a dedicated capture register: Mode 0: Capture is performed in response to a transition at the corresponding port 1 pins CC0 to CC3. Mode 1: Write operation into the low-order byte of the dedicated capture register causes the timer 2 contents to be latched into this register.
Semiconductor Group
236
Device Specifications
Compare In the compare mode, the 16-bit values stored in the dedicated compare registers are compared to the contents of the timer 2 registers. If the count value in the timer 2 registers matches one of the stored values, an appropriate output signal is generated and an interrupt is requested. Two compare modes are provided: Mode 0: Upon a match the output signal changes from low to high. It goes back to a low level when timer 2 overflows. Mode 1: The transition of the output signal can be determined by software. A timer 2 overflow causes no output change .
Figure 3 Block Diagram of Timer/Counter 2 Semiconductor Group 237
Device Specifications
Serial Port The serial port of the SAB 80C515 enables full duplex communication between microcontrollers or between microcontroller and peripheral devices. The serial port can operate in 4 modes: Mode 0: Shift register mode. Serial data enters and exits through RxD. TxD outputs the shift clock. 8-bits are transmitted/received: 8 data bits (LSB first). The baud rate is fixed at 1/12 of the oscillator frequency. Mode 1: 10-bits are transmitted (through RxD) or received (through TxD): a start bit (0), 8 data bits (LSB first), and a stop bit (1). The baud rate is variable. Mode 2: 11-bits are transmitted (through RxD) or received (through TxD): a start bit (0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). The baud rate is programmable to either 1/32 or 1/64 of the oscillator frequency. Mode 3: 11-bits are transmitted (through TxD) or received (through RxD): a start bit (0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). Mode 3 is identical to mode 2 except for the baud rate. The baud rate in mode 3 is variable. The variable baud rates in modes 1 and 3 can be generated by timer 1 or an internal baud rate generator. A/D Converter The 8-bit A/D converter of the SAB 80C515 has eight multiplexed analog inputs (Port 6) and uses the successive approximation method. There are three characteristic time frames in a conversion cycle (see A/D converter characteristics): the conversion time tC, which is the time required for one conversion; the sample time tS which is included in the conversion time and is measured from the start of the conversion; the load time tL, which in turn is part of the sample time and also is measured from the conversion start. Within the load time tL, the analog input capacitance CI must be loaded to the analog inpult voltage level. For the rest of the sample time tS, after the load time has passed, the selected analog input must be held constant. During the rest of the conversion time tC the conversion itself is actually performed. Conversion can be programmed to be single or continuous; at the end of a conversion an interrupt can be generated. A unique feature is the capability of internal reference voltage programming. The internal reference voltages V I ntAREF and V I ntAGND for the A/D converter both are programmable to one of 16 steps with respect to the external reference voltages. This feature permits a conversion with a smaller internal reference voltage range to gain a higher resolution. In addition, the internal reference voltages can easily be adapted by software to the desired analog input voltage range. Figure 4 shows a block diagram of the A/D converter.
Semiconductor Group
238
Device Specifications
Figure 4 Block Diagram of the A/D Converter
Semiconductor Group
239
Device Specifications
Interrupt Structure The SAB 80C515 has 12 interrupt vectors with the following vector addresses and request flags: Table 3 Interrupt Sources and Vectors Source (Request Flags) IE0 TF0 IE1 TF1 RI + TI TF2 + EXF2 IADC IEX2 IEX3 IEX4 IEX5 IEX6 Vector Address 0003H 000BH 0013H 001BH 0023H 002BH 0043H 004BH 0053H 005BH 0063H 006BH Vector External interrupt 0 Timer 0 interrupt External interrupt 1 Timer 1 interrupt Serial port interrupt Timer 2 interrupt A/D converter interrupt External interrupt 2 External interrupt 3 External interrupt 4 External interrupt 5 External interrupt 6
Each interrupt vector can be individually enabled/disabled. The minimum response time to an interrupt request is more than 3 machine cycles and less than 9 machine cycles. Figure 5 shows the interrupt request sources. External interrupts 0 and 1 can be activated by a low-level or a negative transition (selectable) at their corresponding input pin, external interrupts 2 and 3 can be programmed for triggering on a negative or a positive transition. The external interrupts 3 or 6 are combined with the corresponding alternate functions compare (output) and capture (input) on port 1. For programming of the priority levels the interrupt vectors are combined to pairs. Each pair can be programmed individually to one of four priority levels by setting or clearing one bit in the special function register IP0 and one in IP1. Figure 6 shows the priority level structure.
Semiconductor Group
240
Device Specifications
Figure 5 Interrupt Request Sources Semiconductor Group 241
Device Specifications
Figure 6 Interrupt Priority Level Structure Semiconductor Group 242
Device Specifications
Watchdog Timer This feature is provided as a means of graceful recovery from a software upset. After an external reset, the watchdog timer is cleared and stopped. It can be started and cleared by software, but it cannot be stopped during active mode of the device. If the software fails to clear the watchdog timer at least every 65532 machine cycles (about 65 ms if a 12 MHz oscillator frequency is used), an internal reset will be initiated. The reset cause (external reset or reset caused by the watchdog) can be examined by software. To clear the watchdog, two bits in two different special function registers must be set by two consecutive instructions (bits IEN0.6 and IEN1.6). This is done to prevent the watchdog from being cleared by unexpected opcodes. It must be noted, however, that the watchdog timer is halted during the idle mode and powerdown mode of the processor (see section "Power Saving Modes" below). Therefore, it is possible to use the idle mode in combination with the watchdog timer function. But even the watchdog timer cannot reset the device when one of the power saving modes has been is entered accidentally. For these reasons several precautions are taken against unintentional entering of the powerdown or idle mode (see below). Power Saving Modes The ACMOS technology of the SAB 80C515 allows two new power saving modes of the device: The idle mode and the power-down mode. These modes replace the power-down supply mode via pin V PD of the SAB 80515 (NMOS). The SAB 80C515 is supplied via pins V CC also during idle and power-down operation. However, there are applications where unintentional entering of these power saving modes must be absolutely avoided. Such critical applications often use the watchdog timer to prevent the system from program upsets. Then accidental entering of the power saving modes would even stop the watchdog timer and would circumvent the watchdog timer's task of system protection. Thus, the SAB 80C515 has an extra pin that allows it to disable both of the power saving modes. When pin PE is held high, idle mode and power-down mode are completely disabled and the instruction sequences that are used for entering these modes (see below) will NOT affect the normal operations of the device. When PE is held low, the use of the idle mode and power-down mode is possible as described in the following sections. Pin PE has a weak internal pullup resistor. Thus, when left open, the power saving modes are disabled. The Special Function Register PCON In the NMOS version SAB 80515 the SFR PCON (address 87H) contains only bit SMOD; in the CMOS version SAB 80C515 there are more bits used (see table 4). The bits PDE, PDS and IDLE, IDLS select the power-down mode or the idle mode, respectively, when the use of the power saving modes is enabled by pin PE (see next page).
Semiconductor Group
243
Device Specifications
If the power-down mode and the idle mode are set at the same time, power-down takes precedence. Furthermore, register PCON contains two general purpose flags. For example, the flag bits GF0 and GF1 can be used to give an indication if an interrupt occurred during normal operation or during an idle. Then an instruction that activates Idle can also set one or both flag bits. When idle is terminated by an interrupt, the interrupt service routine can examine the flag bits. The reset value of PCON is 000X0000B. Table 4 SFR PCON (87H) SMOD 7 Symbol SMOD PDS PDS 6 IDLS 5 Position PCON.7 PCON.6 - 4 Function When set, the baud rate of the serial channel in mode 1, 2, 3 is doubled. Power-down start bit. The instruction that sets the PDS flag bit is the last instruction before entering the power-down mode. Idle start bit. The instruction that sets the IDLS flag bit is the last instruction before entering the idle mode. Reserved General purpose flag General purpose flag Power-down enable bit. When set, starting of the powerdown mode is enabled. Idle mode enable bit. When set, starting of the idle mode is enabled. GF1 3 GF0 2 PDE 1 IDLE 0 87H
IDLS - GF1 GF0 PDE IDLE
PCON.5 PCON.4 PCON.3 PCON.2 PCON.1 PCON.0
Idle Mode In the idle mode the oscillator of the SAB 80C515 continues to run, but the CPU is gated off from the clock signal. However, the interrupt system, the serial port, the A/D converter, and all timers with the exception of the watchdog timer are further provided with the clock. The CPU status is preserved in its entirety: the stack pointer, program counter, program status word, accumulator, and all other registers maintain their data during idle mode. The reduction of power consumption, which can be achieved by this feature depends on the number of peripherals running.
Semiconductor Group
244
Device Specifications
If all timers are stopped and the A/D converter and the serial interface are not running, the maximum power reduction can be achieved. This state is also the test condition for the idle mode ICC (see DC characteristics, note 5). So the user has to take care which peripheral should continue to run and which has to be stopped during idle mode. Also the state of all port pins - either the pins controlled by their latches or controlled by their secondary functions - depends on the status of the controller when entering idle mode. Normally the port pins hold the logical state they had at the time idle mode was activated. If some pins are programmed to serve their alternate functions they still continue to output during idle mode if the assigned function is on. This applies to the compare outputs as well as to the clock output signal or to the serial interface in case it cannot finish reception or transmission during normal operation. The control signals ALE and PSEN hold at logic high levels (see table 5). Table 5 Status of External Pins During Idle and Power-Down Mode Last instruction executed from internal code memory Outputs ALE PSEN PORT 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 Idle High High Data Data/alternate outputs Data Data/alternate outputs Data Data Power-down Low Low Data Data/last output Data Data/last output Data Data Last instruction executed from external code memory Idle High High Float Data/alternate outputs Address Data/alternate outputs Data Data Power-down Low Low Float Data/last output Data Data/last output Data Data
As in normal operation mode, the ports can be used as inputs during idle mode. Thus a capture or reload operation can be triggered, the timers can be used to count external events, and external interrupts will be detected. The idle mode is a useful feature which makes it possible to "freeze" the processor's status - either for a predefined time, or until an external event reverts the controller to normal operation, as discussed below. The watchdog timer is the only peripheral which is automatically stopped during idle mode. If it were not disabled on entering idle mode, the watchdog timer would reset the controller, thus abandoning the idle mode.
Semiconductor Group
245
Device Specifications
When idle mode is used, pin PE must be held on low level. The idle mode is then entered by two consecutive instructions. The first instruction sets the flag bit IDLE (PCON.0) and must not set bit IDLS (PCON.5), the following instruction sets the start bit IDLS (PCON.5) and must not set bit IDLE (PCON.0). The hardware ensures that a concurrent setting of both bits, IDLE and IDLS, does not initiate the idle mode. Bits IDLE and IDLS will automatically be cleared after being set. If one of these register bits is read the value that appears is 0 (see table 4). This double instruction is implemented to minimize the chance of an unintentional entering of the idle mode which would leave the watchdog timer's task of system protection without effect. Note that PCON is not a bit-addressable register, so the above mentioned sequence for entering the idle mode is obtained by byte-handling instructions, as shown in the following example: ORL ORL PCON,#00000001B PCON,#00100000B ;Set bit IDLE, bit IDLS must not be set
;Set
bit IDLS, bit IDLE must not be set
The instruction that sets bit IDLS is the last instruction executed before going into idle mode. There are two ways to terminate the idle mode: - The idle mode can be terminated by activating any enable interrupt. This interrupt will be serviced and normally the instruction to be executed following the RETI instruction will be the one following the instruction that sets the bit IDLS. - The other way to terminate the idle mode, is a hardware reset. Since the oscillator is still running, the hardware reset must be held active only for two machine cycles for a complete reset. Power-Down Mode In the power-down mode, the on-chip oscillator is stopped. Therefore all functions are stopped; only the contents of the on-chip RAM and the SFR's are maintained.The port pins controlled by their port latches output the values that are held by their SFR's. The port pins which serve the alternate output functions show the values they had at the end of the last cycle of the instruction which initiated the power-down mode; when the clockout signal (CLKOUT, P1.6) is enabled, it will stop at low level. ALE and PSEN hold at logic low level (see table 5). To enter the power-down mode the pin PE must be on low level. The power-down mode then is entered by two consecutive instructions. The first instruction has to set the flag bit PDE (PCON.1) and must not set bit PDS (PCON.6), the following instruction has to set the start bit PDS (PCON.6) and must not set bit PDE (PCON.1). The hardware ensures that a concurrent setting of both bits, PDE and PDS, does not initiate the power-down mode. Bits PDE and PDS will automatically be cleared after having been set and the value shown by reading one of these bits is always 0 (see table 4). This double instruction is implemented to minimize the chance of unintentionally entering the power-down mode which could possibly "freeze" the chip's activity in an undesired status.
Semiconductor Group
246
Device Specifications
Note that PCON is not a bit-addressable register, so the above mentioned sequence for entering the power-down mode is obtained by byte-handling instructions, as shown in the following example: ORL ORL PCON,#00000010B PCON,#01000000B ;Set bit PDE, bit PDS must not be set ;Set bit PDS, bit PDE must not be set
The instruction that sets bit PDS is the last instruction executed before going into power-down mode. The only exit from power-down mode is a hardware reset. Reset will redefine all SFR's, but will not change the contents of the internal RAM. In the power-down mode of operation, VCC can be reduced to minimize power consumption. It must be ensured, however, that VCC is not reduced before the power- down mode is invoked, and that VCC is restored to its normal operating level, before the power-down mode is terminated. The reset signal that terminates the power-down mode also restarts the oscillator. The reset should not be activated before VCC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize (similar to power-on reset). Differences in Pin Assignments of the SAB 80C515 and SAB 80515 Since the SAB 80C515 is designed in CMOS technology, this device requires no V B B pin, because the die's substrate is internally connected to V CC. Furthermore, the RAM backup power supply via pin V PD is replaced by the software- controlled power-down mode and power supply via V CC. Therefore, pins V B B and V PD of the NMOS version SAB 80515 are used for other functions in the SAB 80C515. Pin 4 (the former pin V PD) is the new PE pin which enables the use of the power saving modes. Pin 37 (the former pin V BB) becomes an additional V CC pin. Thus, it is possible to insert a decoupling capacitor between pin 37 (VCC) and pin 38 (VSS) very close to the device, thereby avoiding long wiring and reducing the voltage distortion resulting from high dynamic current peaks. There is a difference between the NMOS and CMOS version concerning the clock circuitry. When the device is driven from an external source, pin XTAL2 must be driven by the clock signal; pin XTAL1, however, must be left open in the SAB 80C515 (must be tied low in the NMOS version). When using the oscillator with a crystal there is no difference in the circuitry. Thus, due to its pin compatibility the SAB 80C515 normally substitutes any SAB 80515 without redesign of the user's printed circuit board, but the user has to take care that the two VCC pins are hardwired on-chip. In any case, it is recommended that power is supplied on both VCC pins of the SAB 80C515 to improve the power supply to the chip. If the power saving modes are to be used, pin PE must be tied low, otherwise these modes are disabled.
Semiconductor Group
247
Device Specifications
Instruction Set The SAB 80C515 / 83C535 has the same instruction set as the industry standard 8051 microcontroller. A pocket guide is available which contains the complete instruction set in functional and hexadecimal order. Furtheron it provides helpful information about Special Function Registers, Interrupt Vectors and Assembler Directives. Literature Information Title Microcontroller Family SAB 8051 Pocket Guide Ordering No. B158-H6579-X-X-7600
Semiconductor Group
248
Device Specifications
Absolute Maximum Ratings Ambient temperature under bias SAB 80C515 SAB 80C515-T3 Storage temperature Voltage on V CC pins with respect to ground (VSS) Voltage on any pin with respect to ground (VSS) Input current on any pin during overload condition Absolute sum of all input currents during overload condition Power disipation 0 to 70 C - 40 to 85 C - 65 to 150 C - 0.5 to 6.5 V - 0.5 to VCC + 0.5 V - 10 mA to + 10 mA |100 mA| 2W
Note Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage of the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for longer periods may affect device reliability. During overload conditions (V I N > V CC or V I N < V SS) the Voltage on VCC pins with respect to ground (VSS) must not exeed the values defined by the absolute maximum ratings.
DC Characteristics V CC = 5 V 10 %; VSS = 0 V
T A = 0 to 70 C for the SAB 80C515/80C535 T A = - 40 to 85 C for the SAB 80C515/80C535-T3 Symbol Limit values min. max. 0.2 VCC - 0.1 0.2 VCC - 0.3 VCC + 0.5 VCC + 0.5 VCC + 0.5 - 0.45
V -
Parameter
Unit
Test condition
Input low voltage (except EA) Input low voltage (EA) Input high voltage (except RESET and XTAL2) Input high voltage to XTAL2 Input high voltage to RESET Output low voltage, ports 1, 2, 3, 4, 5
Notes see page 251.
VI L V I L1 VI H V I H1 V I H2 VOL
- 0.5 - 0.5 0.2 VCC + 0.9 0.7 VCC 0.6 VCC
-
V
-
V
-
V
-
V
-
V
I OL = 1.6 mA 1)
Semiconductor Group
249
Device Specifications
DC Characteristics (cont'd) Parameter Symbol Limit values min. Output low voltage, port 0, ALE, PSEN Output high voltage, ports 1, 2, 3, 4, 5 Output high voltage (port 0 in external bus mode, ALE, PSEN) VOL1 VOH V OH1
-
Unit
Test condition
max. 0.45
- - - -
V V V V V A A A A A A pF
I OL = 3.2 mA 1) I OH = - 80 A I OH = - 10 A I OH = - 400 A I OH = - 40 A 2) VI N = 0.45 V VI N = 0.45 V VI N = 0.45 V VI N = 0.45 V VI N = 2 V 0.45 < V I N < V CC f C = 1 MHz, T A = 25 C VCC = 5 V 4) VCC = 5 V 5) VCC = 5 V 4) VCC = 5 V 5) VCC = 2 V to 5.5 V 3)
2.4 0.9 V C C 2.4 0.9 V C C - 10 - 10 - - - 65 - -
Logic 0 input current, ports 1, 2, IIL 3, 4, 5 Input low current to RESET for reset Input low current (XTAL2) Input low current (PE) IIL2 I I L3 I I L4
- 70 - 100 - 15 - 20 - 650 1 10
Logical 1-to-0 transition current, ITL ports 1, 2, 3, 4, 5 Input leakage current (port 0, port 6, AN0-7, EA) Pin capacitance Power-supply current: 6) Active mode, 12 MHz 6) Idle mode, 12 MHz 6) Active mode, 16 MHz 6) Idle mode, 16 MHz Power-down mode IL I CI O
- ICC - ICC - ICC - ICC - IPD
- - - - -
35 13 46 17 50
mA mA mA mA A
Notes see page 251.
Semiconductor Group
250
Device Specifications
Notes for page 249 and 250: 1) Capacitive loading on ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOL of ALE and ports 1, 3, 4 and 5. The noise is due to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operation. In the worst case (capacitive loading > 100 pF), the noise pulse on ALE line may exceed 0.8 V. Then, it may be desirable to qualify ALE with a Schmitttrigger, or use an address latch with a Schmitttrigger strobe input. 2) Capacitive loading on ports 0 and 2 may cause the VOH on ALE and PSEN to momentarily fall below the 0.9 VCC specification when the address bits are stabilizing. 3) Power-down ICC is measured with: EA = Port 0 = Port 6 = V CC; XTAL1 = N.C.; XTAL2 = V SS; RESET = VCC; VAGND = V SS; all other pins are disconnected. 4) ICC(active mode) is measured with: XTAL2 driven with the clock signal according to the figure below; XTAL1 = N.C.; EA = Port 0 = Port 6 = VCC; RESET = V SS; all other pins are disconnected. ICC might be slightly higher if a crystal oscillator is used. 5) ICC (idle mode) is measured with: XTAL2 driven with the clock signal according to the figure below; XTAL1 = N.C.; EA = V SS; Port 0 = Port 6 VCC; RESET = VCC; all other pins are disconnected; all on-chip peripherals are disabled. 6) ICC at other frequencies is given by: Active mode: ICC max (mA) = 2.67 x f OSC (MHz) + 3.00 Idle mode: ICC max (mA) = 0.88 x f OSC (MHz) + 2.50 where f OSC is the oscillator frequency in MHz. ICC max is given in mA and measured at VCC = 5 V (see also notes 4 and 5)
Semiconductor Group
251
Device Specifications
A/D Converter Characteristics V CC = 5 V 10 %; VSS = 0 V; V AREF = V CC 5 %; V AGND = VSS 0.2 V; V I ntAREF - VI ntAGND 1 V; T A = 0 to 70 C for SAB 80C515/80C535 T A = - 40 to 85 C for SAB 80C515/80C535-T40/85 Parameter Symbol min. Analog input voltage Analog input capacitance Load time Sample time (incl. load time) Conversion time (incl. sample time) Total unadjusted error V AINPUT CI tL tS tC
TUE
Limit values typ.
-
Unit
Test condition
max. V AREF + 0.2 45 2 t CY 7 t CY 13 t CY 2 V pF s s s LSB
9)
VAGND - 0.2 - - - - -
25 - - - 1
7)
- - - V I ntAREF = VAREF = VCC V I ntAGND = V AGND = VSS7)
8) 8)
VAREF supply current
Internal reference error
7)
I REF V I nt REFERR
- -
-
5 30
mA mV
The output impedance of the analog source must be low enough to assure full loading of the sample capacitance (C I ) during load time (t L ) . After charging of the internal capacitance (C I ) i n the load time (t L ) the analog input must be held constant for the rest of the sample time (tS ) The differential impedance r D of the analog reference voltage source must be less than 1 k at reference supply voltage. Exceeding these limit values at one or more input channels will cause additional current which is sinked / sourced at these channels. This may also affect the accuracy of other channels which are operated within these specifications.
8)
9)
Semiconductor Group
252
Device Specifications
AC Characteristics V CC = 5 V 10%; V SS = 0 V (C L for Port 0, ALE and PSEN outputs = 100 pF; C L for all outputs = 80 pF); T A = 0 to 70 C for SAB 80C515/80C535 T A = - 40 to 85 C for SAB 80C515/80C535-T40/85 Parameter Symbol 12 MHz clock min. Program Memory Characteristics ALE pulse width Address setup to ALE Address hold after ALE ALE to valid instruction in ALE to PSEN PSEN pulse width t LHLL t AVLL t LLAX t LLIV t LLPL t PLPH 127 53 48 - 58 215 - 0 - 75 - 0 302 - 150 - 63 - - - 233 - 2 t C LCL - 40 t C LCL - 30 t C LCL - 35 - t C LCL - 25 3 t C LCL - 35 - 0
-
Limit values Variable clock 1/tCLCL = 3.5 MHz to 12 MHz min. max.
Unit
max.
- - - 4 t C LCL - 100 -
ns ns ns ns ns ns
PSEN to valid instruction t PLIV in Input instruction hold after PSEN Input instruction float after PSEN Address valid after PSEN Address to valid instruction in Address float to PSEN
1)
3 t C LCL - 100
-
ns ns ns ns
t PXIX t PXIZ 1) t PXAV 1) t A VIV t A ZPL
t C LCL - 20
t C LCL - 8
-
5 t C LCL - 115
-
ns ns
0
Interfacing the SAB 80C515 to devices with float times up to 75 ns is permissible. This limited bus contention will not cause any damage to port 0 drivers.
Semiconductor Group
253
Device Specifications
AC Characteristics (cont'd) Parameter Symbol 12 MHz clock min. External Data Memory Characteristics RD pulse width WR pulse width Address hold after ALE RD to valid data in DATA hold after RD Data float after RD ALE to valid data in Address to valid data in ALE to WR or RD WR or RD high to ALE high Address valid to WR Data valid to WR transition Data setup before WR Data hold after WR Address float after RD t RLRH t WLWH t LLAX2 tRLDV t RHDX t RHDZ t LLDV t AVDV t LLWL t WHLH t AVWL t QVWX tQVWH tWHQX tRLAZ 400 400 132 - 0 - - - 200 43 203 33 288 13 - - - - 252 - 97 517 585 300 123 - - - - 0 6 tCLCL - 100 6 tCLCL - 100 2 tCLCL - 35
- - - -
Limit values Variable clock 1/tCLCL = 3.5 MHz to 12 MHz min. max.
Unit
max.
ns ns ns ns ns
5 tCLCL - 165
0
- - -
2 tCLCL - 70 8 tCLCL - 150 9 tCLCL - 165 3 tCLCL + 50 tCLCL + 40 - - - - 0
ns ns ns ns ns ns ns ns ns ns
3 tCLCL - 50 tCLCL - 40 4 tCLCL - 130 tCLCL - 50 7 tCLCL - 150 tCLCL - 50 -
Semiconductor Group
254
Device Specifications
AC Characteristics (cont'd) Parameter Symbol Limit values Variable clock Frequ. = 3.5 MHz to 12 MHz min. External Clock Drive Oscillator period Oscillator frequency High time Low time Rise time Fall time tCLCL 1/tCLCL t CHCX tCLCX tCLCH tCHCL 83.3 0.5 20 20
- -
Unit
max.
285 12
- -
ns MHz ns ns ns ns
20 20
t CLCL VCC- 0.5V
0.7 VCC 0.2 VCC- 0.1
0.45V
t CHCL
t CLCX t CLCH
t CHCX
MCT00033
External Clock Cycle
Semiconductor Group
255
Device Specifications
AC Characteristics (cont'd) Parameter Symbol 12 MHz clock Limit values Variable clock 1/tCLCL = 3.5 MHz to 12 MHz min. max. Unit
min. System Clock Timing ALE to CLKOUT CLKOUT high time CLKOUT low time CLKOUT low to ALE high tLLSH tSHSL tSLSH tSLLH 543 127 793 43
max.
- - - 123
7 tCLCL - 40 2 tCLCL - 40 10 tCLCL - 40 tCLCL - 40
- - - tCLCL + 40
ns ns ns ns
System Clock Timing
Semiconductor Group
256
Device Specifications
AC Characteristics for SAB 80C515-16/80C535-16 VCC = 5 V 10 %; VSS = 0 V (C L for Port 0, ALE and PSEN outputs = 100 pF; C L for all outputs = 80 pF) T A = 0 to 70 C for SAB 80C515-16/80C535-16 T A = - 40 to 85 C for SAB 80C515-16/80C535-16-T40/85 Parameter Symbol 16 MHz clock min. Program Memory Characteristics ALE pulse width Address setup to ALE Address hold after ALE ALE to valid instruction in ALE to PSEN PSEN pulse width t LHLL t AVLL t LLAX t LLIV t LLPL t PLPH 85 33 28
- - - -
Limit values Variable clock 1/tCLCL = 3.5 MHz to 16 MHz min. max.
Unit
max.
2 t C LC L - 40 tCLCL - 30 tCLCL - 35
-
- - -
ns ns ns ns ns ns
150
-
4 tCLCL - 100
-
38 153
-
tCLCL - 25 3 tCLCL - 35
PSEN to valid instruction t PLIV in Input instruction hold after PSEN Input instruction float after PSEN Address valid after PSEN Address to valid instruction in Address float to PSEN
1)
88
-
-
3 tCLCL - 100
-
ns ns
t PXIX
0
0
t PXIZ 1)
-
43
-
tCLCL - 20
ns
t PXAV1) t AVIV t AZPL
55
-
tCLCL - 8 198
- -
ns 5 tCLCL - 115
-
ns ns
0
0
Interfacing the SAB 80C515-16 to devices with float times up to 55 ns is permissible. This limited bus contention will not cause any damage to port 0 drivers.
Semiconductor Group
257
Device Specifications
AC Characteristics (cont'd) Parameter Symbol 16 MHz clock min. External Data Memory Characteristics RDpulse width WR pulse width Address hold after ALE RD to valid data in Data hold after RD Data float after RD ALE to valid data in Address to valid data in ALE to WR or RD WR or RD high to ALE high Address valid to WR Data valid to WR transition Data setup before WR Data hold after WR Address float after RD tRLRH tWLWH tLLAX2 tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tWHLH tAVWL tQVWX tQVWH tWHQX tRLAZ 275 275 90 - 0 - - - 138 23 120 13 288 13 - - - - 148 - 55 350 398 238 103 - - - - 0 6 tCLCL - 100 6 tCLCL - 100 2 tCLCL - 35 - 0 - - - 3 tCLCL - 50 tCLCL - 40 4 tCLCL - 130 tCLCL - 50 7 tCLCL - 150 tCLCL - 50 - - - - 5 tCLCL - 165 - 2 tCLCL - 70 8tCLCL - 150 9 tCLCL - 165 3 tCLCL + 50 tCLCL + 40 - - - - 0 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns max. Limit values Variable clock 1/tCLCL = 3.5 MHz to 16 MHz min. max. Unit
Semiconductor Group
258
Device Specifications
AC Characteristics (cont'd) Parameter Symbol Limit values Variable clock Frequ. = 3.5 MHz to 16 MHz min. External Clock Drive Oscillator period Oscillator frequency High time Low time Rise time Fall time tCLCL 1/tCLCL tCHCX tCLCX tCLCH tCHCL 62.5 0.5 15 15
- -
Unit
max.
285 16
- -
ns MHz ns ns ns ns
15 15
t CLCL VCC- 0.5V
0.7 VCC 0.2 VCC- 0.1
0.45V
t CHCL
t CLCX t CLCH
t CHCX
MCT00033
External Clock Cycle
Semiconductor Group
259
Device Specifications
AC Characteristics (cont'd) Parameter Symbol 16 MHz clock Limit values Variable clock 1/tCLCL = 3.5 MHz to 16 MHz min. max. Unit
min. System Clock Timing ALE to CLK OUT CLK OUT high time CLK OUT low time CLK OUT low to ALE high tLLSH tSHSL tSLSH tSLLH 398 85 585 23
max.
- - - 103
7 tCLCL - 40 2 tCLCL - 40 10 tCLCL - 40 tCLCL - 40
- - - tCLCL + 40
ns ns ns ns
System Clock Timing
Semiconductor Group
260
Device Specifications
AC Characteristics for SAB 80C515-20 / 80C535-20 VCC = 5 V 10 %; VSS = 0 V TA = 0 C to + 70 C (CL for port 0, ALE and PSEN outputs = 100 pF; CL for all other outputs = 80 pF) Parameter Symbol 20 MHz clock min. Program Memory Characteristics ALE pulse width Address setup to ALE Address hold after ALE ALE low to valid instr in ALE to PSEN PSEN pulse width PSEN to valid instr in Input instruction hold after PSEN Input instruction float after PSEN Address valid after PSEN Address to valid instr in Address float to PSEN tLHLL tAVLL tLLAX tLLIV tLLPL tPLPH tPLIV tPXIX tPXIZ*) tPXAV*) tAVIV tAZPL 60 20 20 - 25 115 - 0 - 47 - 0 - - - 100 - - 75 - 40 - 190 - 2 tCLCL - 40 tCLCL - 30 tCLCL - 30 - tCLCL - 25 3 tCLCL - 35 - 0 - tCLCL - 3 - 0 - - - 4 tCLCL- 100 - - 3 tCLCL - 75 - tCLCL - 10 - 5 tCLCL - 60 - ns ns ns ns ns ns ns ns ns ns ns ns max. Limit values Variable clock 1/tCLCL = 3.5 MHz to 20 MHz min. max. Unit
*) Interfacing the SAB 80C515 / 80C535 microcontrollers to devices with float times up to 45 ns is permissible.
This limited bus contention will not cause any damage to port 0 drivers.
Semiconductor Group
261
Device Specifications
AC Characteristics (cont'd) Parameter Symbol 20 MHz clock min. External Data Memory Characteristics RD pulse width WR pulse width Address hold after ALE RD to valid data in Data hold after RD Data float after RD ALE to valid data in Address to valid data in ALE to WR or RD Address valid to WR or RD WR or RD high to ALE high Data valid to WR transition Data setup before WR Data hold after WR Address float after RD tRLRH tWLWH tLLAX2 tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tAVWL tWHLH tQVWX tQVWH tWHQX tRLAZ 200 200 65 - 0 - - - 100 70 20 5 200 10 - - - - 155 - 40 250 285 200 - 80 - - - 0 6 tCLCL - 100 6 tCLCL - 100 2 tCLCL - 35 - 0 - - - 3 tCLCL - 50 4 tCLCL - 130 tCLCL - 30 tCLCL - 45 7 tCLCL - 150 tCLCL - 40 - - - - 5 tCLCL - 95 - 2 tCLCL - 60 8 tCLCL - 150 9 tCLCL - 165 3 tCLCL + 50 - tCLCL + 30 - - - 0 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns max. Limit values Variable clock 1/tCLCL = 3.5 MHz to 20 MHz min. max. Unit
Semiconductor Group
262
Device Specifications
AC Characteristics (cont'd) Parameter Symbol Limit Values Variable clock 1/tCLCL = 3.5 MHz to 20 MHz min. External Clock Drive Oscillator period High time Low time Rise time Fall time tCLCL tCHCX tCLCX tCLCH tCHCL 50 12 12 - - 285 tCLCL - tCLCX tCLCL - tCHCX 12 12 ns ns ns ns ns max. Unit
External Clock Cycle
Semiconductor Group
263
Device Specifications
AC Characteristics (cont'd) Parameter Symbol 20 MHz clock min. System Clock Timing ALE to CLKOUT CLKOUT high time CLKOUT low time CLKOUT low to ALE high tLLSH tSHSL tSLSH tSLLH 310 60 460 10 - - - 90 7 tCLCL - 40 2 tCLCL - 40 10 tCLCL - 40 tCLCL - 40 - - - tCLCL + 40 ns ns ns ns max. Limit values Variable clock 1/tCLCL = 3.5 MHz to 20 MHz min. max. Unit
External Clock Cycle
Semiconductor Group
264
Device Specifications
ROM Verification Characteristics T A = 25 C 5 C; V CC = 5 V 10 %; V SS = 0 V Parameter Symbol min. Limit values max. Unit
ROM Verification Address to valid data ENABLE to valid data Data float after ENABLE Oscillator frequency Address to valid data tAVQV tELQV tEHOZ 1/tCLCL1 tAVQV
- -
48 tCLCL 48 tCLCL 48 tCLCL 6 48 tCLCL
ns ns ns MHz ns
0 4
-
P1.0 - P1.7 P2.0 - P2.4
Address
t AVQV
Port 0
Data OUT
t ELQV
t EHQZ
P2.7 ENABLE
MCT00049
Address: P1.0 - P1.7 = A0 - A7 P2.0 - P2.4 = A8 - A12 P0.0 - P0.7 = D0 - D7 Data:
Inputs: P2.5 - P2.6, PSEN = VSS ALE, EA = V IH RESET = V SS
ROM Verification
Semiconductor Group
265
Device Specifications
Waveforms
t LHLL
ALE
t AVLL t
LLIV
t PLPH t LLPL t PLIV
PSEN
t AZPL t LLAX
t PXAV t PXIZ t PXIX
Port 0
A0 - A7
Instr.IN
A0 - A7
t AVIV
Port 2
A8 - A15
A8 - A15
MCT00096
Program Memory Read Cycle
t WHLH
ALE
PSEN
t LLDV t LLWL
RD
t RLRH
t RLDV t AVLL t LLAX2 t RLAZ
Port 0 A0 - A7 from Ri or DPL Data IN
t RHDZ t RHDX
A0 - A7 from PCL Instr. IN
t AVWL t AVDV
Port 2
P2.0 - P2.7 or A8 - A15 from DPH
A8 - A15 from PCH
MCT00097
Data Memory Read Cycle Semiconductor Group 266
Device Specifications
t WHLH
ALE
PSEN
t LLWL
WR
t WLWH
t QVWX t AVLL t LLAX2
A0 - A7 from Ri or DPL
t WHQX t QVWH
Data OUT A0 - A7 from PCL Instr.IN
Port 0
t AVWL
Port 2 P2.0 - P2.7 or A8 - A15 from DPH A8 - A15 from PCH
MCT00098
AC inputs during testing are driven at
V C C - 0.5 V for a logic '1' and 0.45 V for a logic '0'. Timing measurements are made at V I H min for a logic '1' and V I L max for a logic '0'.
Data Memory Write Cycle
For timing purposes a port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV deviation from the load voltage V O H/V O L occurs. I O L/I O H 20 mA.
Recommended Oscillator Circuits
Semiconductor Group
267
Device Specifications
AC Testing: Input, Output Waveforms
AC Testing: Float Waveforms
Semiconductor Group
268
Device Specifications
Package Outlines
Plastic Package, P-LCC-68 - SMD (Plastic Leaded Chip-Carrier)
Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book "Package Information". SMD = Surface Mounted Device Dimensions in mm
Semiconductor Group
269
Device Specifications
Package Outlines Plastic Package, P-MQFP-80 - SMD (Plastic Metric Quad Flat Package)
Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book "Package Information". SMD = Surface Mounted Device Dimensions in mm
Semiconductor Group
270

▲Up To Search▲

Price & Availability of SAB80515

	To Download SAB80515 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .